related cleanups:
- Require each driver to initalize a mutex in the scsi_low_softc that
is shared with the scsi_low code. This mutex is used for CAM SIMs,
timers, and interrupt handlers.
- Replace the osdep function switch with direct calls to the relevant
CAM functions and direct manipulation of timers via callout(9).
- Collapse the CAM-specific scsi_low_osdep_interface substructure
directly into scsi_low_softc.
- Use bus_*() instead of bus_space_*().
- Return BUS_PROBE_DEFAULT from probe routines instead of 0.
- No need to zero softcs.
- Pass 0ul and ~0ul instead of 0 and ~0 to bus_alloc_resource().
- Spell "dettach" as "detach".
- Remove unused 'dvname' variables.
- De-spl().
Tested by: no one
drivers:
- Remove scsi_low_pisa.*, they were unused.
- Remove <compat/netbsd/physio_proc.h> and calls to the stubs in that
header. They were empty nops.
- Retire sl_xname and use device_get_nameunit() and device_printf() with
the underlying device_t instead.
- Remove unused {ct,ncv,nsp,stg}print() functions.
- Remove empty SOFT_INTR_REQUIRED() macro and the unused sl_irq member.
NetBSD/pc98 was never merged into the main NetBSD tree and is no longer
developed. Adding locking to these drivers would have made the compat
shims hard to impossible to maintain, so remove the shims to ease
future changes.
These changes were verified by md5. Some additional shims can be removed
that do affect the compiled results that I will probably do in another
round.
Approved by: nyan (tentatively)
Provide a backwards compatible way to have the extra macro by defining
PCCARD_API_LEVEL 5 before including pccarddevs for driver writers that
want/need to have the same driver on 5 and 6 with pccard attachments.
Approved by: re (dwhite)
o Add needed headers.
o Add nsp_producs[] product data and nsp_match() function.
o Change nsp_pccard_method[] to support both OLDCARD and NEWCARD.
o Add warning to fall back to PIO mode when it cannot use SMIT mode.
This is needed because memories are not allocated with NEWCARD now.
Submitted by: takawata
Approved by: re
A nsp chip does suspend I/O write by 512bytes burst write,
though the chip only has 48 bytes FIFO. The chip assert I/O WAIT
signal to PC-Card bus after the CPU writes more than 48 bytes to
the chip if the SCSI device does not respond immediately in supsend
I/O burst write. If the device does not respond for a while it might
cause PC-Card bus timeout.
The previous work around was to wait the request from SCSI device.
But there are some devices which request bytes for synchronous transfer
immediately. So current work aound is to fill 32bytes FIFO, wait for
FIFO empty and burst write 512-32 bytes for every 512 bytes block.
Submitted-by: Honda-san (the author of the driver)
Obtained-from: NetBSD/pc98
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
o Offset and period in synch messages and width negotiation should be
done for per target not per lun. Move these from *lun_info to
*targ_info.
o Change in handling XPT_RESET_DEV and XPT_GET_TRAN_SETTINGS .
o Change CAM_* xpt_done return values.
o Busy loop did not timeout. Change this to timeout as original NetBSD/pc98.
Reviewed by: bsd-nomads ML
used in lower layer (scsi_low.c).
The flag of ncv for KME KXLC004 was chaged from 0x1 to 0x100.
The flag of nsp for PIO mode was chaged from 0x1 to 0x100.
(a NetBSD port for NEC PC-98x1 machines). They are ncv for NCR 53C500,
nsp for Workbit Ninja SCSI-3, and stg for TMC 18C30 and 18C50.
I thank NetBSD/pc98 and bsd-nomads people.
Obtained from: NetBSD/pc98
