Remove silly "Naffy, the Wonder Porpoise" attribution and add more
justifiable (and overdue) attribution to Bruce Evans. Look at it
as a delete and add operation batched together, not a substitution. :-)
notice, performed all of the structural changes necessary to get this thing
to work with the unidirectional-DMA version of voxware.
This work is -not- complete, but it's in far better shape than it was, and
I may not touch it again for another few months.
in read() and write(). FNONBLOCK is valid in ioctl() and close().
The bug caused hung ptys when a process talked to itself using nonblocking
i/o and exited while the slave pty had output to flush. ttywait() was
called and hung. Signals didn't work because the process was exiting.
`comcontrol /dev/ttyp0 drainwait 1' worked to terminate the wait. This
shows that comcontrol is not limited to hardware control. It has no i386
or driver dependencies and doesn't belong in src/sbin/i386.
Bruce
to emit spurious page outside of object type messages. It is not
a fatal condition anyway, so the message will be omitted for
release. Also, the code that "clips" the allocation size, associated
with the above problem, was fixed.
The ``flags 1'' in the fdc line is now only needed for owners of an
Insight tape (perhaps there aren't any? Mine is disfunctional). All
other probes are safe wrt. to the motor-control line of floppy disk
drives. Document the flag in LINT finally.
fragmented.
Added support for Cogent em100 boards.
Fixed bug that caused BPF to toggle the card to UTP.
Various other improvements.
Submitted by: Matt Thomas and David Greenman
Change IPTOS_PREC_ROUTINE to 0 (was conflict with IPTOS_LOWDELAY) according
to RFC 791 (unchanged since it) and BSDI 2.0 style
Submitted by: Igor Sviridov <siac@ua.net>
initializing proc0's frame base, too, using cpu_set_init_frame(). It's
a kludge because that macro is intended to be used only for init, but
does what we want nonetheless.
loading kernel
worm.o: Undefined symbol `_STUNIT' referenced from text segment
I copied the STUNIT definition from the old scsiconf.c into this file to
work around this problem.
if the 'time on a node is 0,..
tell the world it is the same as 'boottime'.
This is becasue 'time' is not set up when we create the nodes,
so we can't set them then.
Added CONTROL device that only does user-ioctl and nothing else;
Added protection so user-ioctl requires write access;
Clean up scsiconf.h a little. It needs more work.
the lookup fails. Updated callers to deal with this. Call in_pcblookuphash
instead of in_pcblookup() in in_pcbconnect; this improves performance of
UDP output by about 17% in the standard case.
space for the hash list buckets and is a little faster. The features
of tailq aren't needed. Increased the size of the object hash table
to improve performance. In the future, this will be changed so that
the table is sized dynamically.
as side-effect, removed some legacy code that was necessary
when we called vm_fault inside of vm_fault_quick instead of using
the kernel/user space byte move routines.
(2GB). If this limit is not imposed, then filesystem corruption will
ensue when files larger than 2GB are created. This is temporary,
and the underlying limitation will be removed later.
algorithm is used on aic7770 Rev E or higher chips to improve perfomance.
This required a hardware change but we don't know exactly what (most
likely some special register to do fast SCB indexing into host memory),
and we are not at all sure that there are more than 4 SCBs on these
chips. This probe will still classify the revision of the aic7xxx, but
we now default to 4 SCBs (at least until we know more of what was done).
This also fixes a bug in the timeout routine where we cleared a flag
too soon making it imposible to enter one section of the routine.
Submitted by: Timeout bug - Dan Eischen <deischen@iworks.InterWorks.org>
interrupts to zero to start with. This is the value we return in
most cases. The sense code then outbs the apropriate value to cause
sense retrieval. The return value was uninitialized before this
change (something that was an okay thing with the old sequencer code,
but not with the semantics of the new).
This problem caused us to always retrieve sense upon recieving a non
zero status byte. This is exactly what was happening for the "target
busy" status returned by exabyte tape drives when they rewind or
power on with a tape installed. The request sense proved fatal.
This should fix the tape problems.
but it outlines what I'm GOING to do to this file.
It's sort of an unignorable notification of coming changes..
This is a bit rude I understand.. but I can't afford to haqve the
diskslice code drifting off too much further from a workable system
and I think I need to jump in now to make it obvious what has to be done
before it's too late.
appologies to bruce in advance.
