instead of old "ignore-and-return 0" in r287789. This broke arp -da /
ndp -cn behavior (they exit on rtsock command failure). Fix this by
translating LLE_IFADDR to RTM_PINNED flag, passing it to userland and
making arp/ndp ignore these entries in batched delete.
MFC after: 2 weeks
These are only handled as 'build-tools' in Makefile.inc1. This causes
'make clean' from the top of the tree to not clean the directories. It also
effectively has kept them disconnected and risks them bitrotting. The
buildworld process never cleans them either.
Connect them so they will always be built, cleaned, etc, but never installed.
Discussed with: imp (briefly)
Sponsored by: EMC / Isilon Storage Division
ndiscvt uses 16 entry array for words into which it parses
comma-separated lists of strings, like AddReg line in
[somesection]
AddReg = foo.reg, bar.reg, baz.reg, quiz.reg
Overflows were not checked so it crashed on a line with 17 words
encountered in some Broadcom/Dell Wireless 1704 802.11b-g-n driver
So extend the array up to 32 entries and add an overflow check.
Reviewed by: bapt
Approved by: bapt
MFC after: 2 weeks
Differential Revision: D3713
- Use NI_MAXHOST-long buffer for getnameinfo().
Although INET6_ADDRSTRLEN was designed to hold the longest
IPv6 address in IPv4-mapped address format a long time ago,
getnameinfo() can return scope identifier in addition to it.
MFC after: 1 day
in -a flag.
- Fix a bug that sockaddr_in was used where sockaddr_in6 should have
been used. This was not actually harmful because offsetof(struct
sockaddr_in, sin_port) is equal to offsetof(struct sockaddr_in6,
sin6_port).
MFC after: 1 day
- Return an error if no matching device is found when the locate command is run
- Enhance the locate command to be able to address drive bays with no disk, or where the SES controller has not made the mapping to the device name
- Added the fault command, similar to locate, but a different SES property. On some of my controllers locate blinks the activity light, others the fault light. The fault command keeps the fault light on constant.
- Improve the usage() output and use it everywhere
- Added the map command, displays all elements connected to each (or the specified) ses(4) controller
- Added the status command, returns the overall status of the ses(4) controller
Reviewed by: wblock (man page, earlier version)
Approved by: bapt (mentor)
MFC after: 3 weeks
Relnotes: yes
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D3580
that checksum of vdev label should be checked (which is not done
currently).
No functional change.
While I'm there, raise WARNS to 2.
Reviewed by: allanjude
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D3508
resolvconf.conf so that resolvconf won't replace the manually configured
forwarders with dynamically configured ones the next time the lease is
renewed.
Some more automated I2C controllers cannot explicitly create
START/STOP/etc. conditions on the bus.
Instead, the correct condition is set automatically according
to the pending transfer status.
This particular behavior can cause trouble if some I2C slave
requires sending address offset within the chip followed by
the actual data or command. In that case we cannot assume that
the driver will not STOP immediately after sending
offset.
To avoid that, do not split offset transfer from data transfer
for default transmission modes and do exactly that if requested
in command line (stop-start and repeated-start modes).
This more generic approach should cover special cases like
the one described.
Reviewed by: imp
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Mark the user has having been edited if -d option is passed to usermod and
so the request change of home directory actually happen
PR: 203052
Reported by: lenzi.sergio@gmail.com
MFC after: 2 days
