- Don't short-circuit aging tests for unmapped objects. This biases
against unmapped file pages and transient mappings.
- Always honor PGA_REFERENCED. We can now use this after soft busying
to lazily restart the LRU.
- Don't transition directly from active to cached bypassing the inactive
queue. This frees recently used data much too early.
- Rename actcount to act_delta to be more consistent with use and meaning.
Reviewed by: kib, alc
Sponsored by: EMC / Isilon Storage Division
all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and
for general purpose monitoring without tapping any cxgbe or cxl ifnet
directly.
Tracers on the T4/T5 chips provide access to Ethernet frames exactly as
they were received from or transmitted on the wire. On transmit, a
tracer will capture a frame after TSO segmentation, hw VLAN tag
insertion, hw L3 & L4 checksum insertion, etc. It will also capture
frames generated by the TCP offload engine (TOE traffic is normally
invisible to the kernel). On receive, a tracer will capture a frame
before hw VLAN extraction, runt filtering, other badness filtering,
before the steering/drop/L2-rewrite filters or the TOE have had a go at
it, and of course before sw LRO in the driver.
There are 4 tracers on a chip. A tracer can trace only in one direction
(tx or rx). For now cxgbetool will set up tracers to capture the first
128B of every transmitted or received frame on a given port. This is a
small subset of what the hardware can do. A pseudo ifnet with the same
name as the nexus driver (t4nex0 or t5nex0) will be created for tracing.
The data delivered to this ifnet is an additional copy made inside the
chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual.
/* watch cxl0, which is the first port hanging off t5nex0. */
# cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting)
# cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving)
# cxgbetool t5nex0 tracer list
# tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire
If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K
"frames" with no L3/L4 checksum but this will show you the frames that
were actually transmitted.
/* all done */
# cxgbetool t5nex0 tracer 0 disable
# cxgbetool t5nex0 tracer 1 disable
# cxgbetool t5nex0 tracer list
# ifconfig t5nex0 destroy
The BSD-licensed patch(1) command has matured and it's behaviour
can be considered equivalent to the older version of GNU patch
in the tree.
The switch has been extensively tested [1] and only two ports
presented regressions, which have since been fixed.
For convenience a new WITH_GNU_PATCH option is available,
but it will likely be removed in the near future.
PR: 176313
Approved by: portmgr
sysctl tree.
* Create a net.link.lagg.X.lacp node
* Add a debug node under that for tx_test and rx_test
* Add lacp_strict_mode, defaulting to 1
tx_test and rx_test are still a bitmap of unit numbers for now.
At some point it would be nice to create child nodes of the lagg bundle
for each sub-interface, and then populate those with various knobs
and statistics.
Sponsored by: Netflix
This eliminates some unusual uses of that API in favor of more typical
uses of kmem_malloc().
Discussed with: kib/alc
Tested by: pho
Sponsored by: EMC / Isilon Storage Division
Before this change path matching had the following features:
- for device nodes the patterns were matched against full path
- in the above case '/' in a path could be matched by a wildcard
- for directories and links only the last component was matched
So, for example, a pattern like 're*' could match the following entries:
- re0 device
- responder/u0 device
- zvol/recpool directory
Although it was possible to work around this behavior (once it was spotted
and understood), it was very confusing and contrary to documentation.
Now we always match a full path for all types of devfs entries (devices,
directories, links) and a '/' has to be matched explicitly.
This behavior follows the shell globbing rules.
This change is originally developed by Jaakko Heinonen.
Many thanks!
PR: kern/122838
Submitted by: jh
MFC after: 4 weeks
Introduce $BASEBITSDIR for clarity and in order to avoid repeating this
mistake in the future. Fixing this ensures that we pick up the newly built
boot code and loader native to the target, which is especially relevant
when cross-building release images.
- It is pointless to specify an endianess for ISO 9660 images so strip that.
MFC after: 3 days
is picked up when defined. Previously, ffs_subr.c was always built without
support for opposite endianess as it doesn't include makefs.h on its own.
MFC after: 3 days
and protocol 1 are USB ethernet adapters. This avoids keeping and updating
the product list every now and then. This patch will add support for the
USB ethernet interface found in the IPAD.
MFC after: 1 week
GCC can generate bogus dwarf attributes with DW_AT_byte_size
set to 0xFFFFFFFF.
The issue was originaly detected in NetBSD but it has been
adapted for portability and to avoid compiler warnings.
Reference:
https://www.illumos.org/issues/3776
Obtained from: NetBSD
MFC after: 1 month
- NOTE_TRACK has never triggered a NOTE_TRACK event from the parent pid.
If NOTE_FORK is set, the listener will get a NOTE_FORK event from
the parent pid, but not a separate NOTE_TRACK event.
- Explicitly note that the event added to monitor the child process
preserves the fflags from the original event.
- Move the description of NOTE_TRACKERR under NOTE_TRACK as it is not a
bit for the user to set (which is what this list pupports to be).
Also, explicitly note that if an error occurs, the NOTE_CHILD event
will not be generated.
MFC after: 1 week
we call device-specific probe functions, which can (and typically will)
set the device description based on low-level device probe information.
In the end we never actually used the device description that we so
carefully maintained in the PCI match table. By setting the device
description after we call uart_probe(), we'll print the more user-
friendly description by default.
- Only enable UDP/TCP hardware checksums if CSUM_UDP or CSUM_TCP is set.
- Only enable IP hardware checksums if CSUM_IP is set.
PR: kern/180430
Submitted by: Meny Yossefi <menyy@mellanox.com>
MFC after: 1 week
as in <sys/dirent.h>
ext2_readdir() has always been very fs specific and different
with respect to its ufs_ counterpart. Recent changes from UFS
have made it possible to share more closely the implementation.
MFUFS r252438:
Always start parsing at DIRBLKSIZ aligned offset, skip first entries if
uio_offset is not DIRBLKSIZ aligned. Return EINVAL if buffer is too
small for single entry.
Preallocate buffer for cookies.
Skip entries with zero inode number.
Reviewed by: gleb, Zheng Liu
MFC after: 1 month
Replace the RESET blocks with regular functions and a reset() function that
calls them all.
This code generation tool is unusual and does not appear to provide much
benefit. I do not think isolating the knowledge about which modules need to
be reset is worth an almost 500-line build tool and wider scope for
variables used by the reset functions.
Also, relying on reset functions is often wrong: the cleanup should be done
in exception handlers so that no stale state remains after 'command eval'
and the like.
These cleanup operations are not needed because they are already performed
after an optimized command substitution (whether there was an error or not).
SVN r95378 refactored ahc_9005_subdevinfo_valid out into a separate
function but swapped the vendor/subvendor and device/subdevice pairs of
the parameters.
Found by: Coverity Prevent, CID 744931
Reviewed by: gibbs
This function is called 4 times in this file, with swapped parameter
ordering. Fix the function definition instead of all the call sites.
16bit/stereo or 8bit/mono playback is unaffected and was probably
working fine before, this should fix 16bit/mono and 8bit/stereo
playback.
Found by: Coverity Scan, CID 1006688
locks don't accidentally appear to have been already
initialized.
In particular, this fixes a consistent kernel crash on
armv6 with:
panic: lock "vm map (user)" 0xc09cc050 already initialized
that appeared with r251709.
PR: arm/180820
Kernel include files (i.e. sys/*.h) come first; normally, include
<sys/types.h> OR <sys/param.h>, but not both. <sys/types.h> includes
<sys/cdefs.h>, and it is okay to depend on that.
to those that are universally administered. While it is possible to
add locally administered MAC addresses, it's unclear whether those
are (expected) to be more unique than random multicast MAC addresses
or not.
With many U-Boot configurations assigning fixed and non-official MAC
addresses to ethernet ports and without setting the 'X' flag, this
change may have very little value in the embedded (development)
space. Uniqueness of the universally administered addresses is non-
existent on the (H/W) bench and questionable under the (S/W) desk.
In short: this change is aimed at production environments...
it gets built 16 times in parallel in the same location.
While we are at it, until we finish getting rid of fmake,
be explicit about the make we want to use, thus avoid the problem
of the temp make being the wrong version.
Reviewed by: obrien
