This includes a new summary mode (-s) for camcontrol defects that
quickly tells the user the most important thing: how many defects
are in the requested list. The actual location of the defects is
less important.
Modern drives frequently have more than the 8191 defects that can
be reported by the READ DEFECT DATA (10) command. If they don't
have that many grown defects, they certainly have more than 8191
defects in the primary (i.e. factory) defect list.
The READ DEFECT DATA (12) command allows for longer parameter
lists, as well as indexing into the list of defects, and so allows
reporting many more defects.
This has been tested with HGST drives and Seagate drives, but
does not fully work with Seagate drives. Once I have a Seagate
spec I may be able to determine whether it is possible to make it
work with Seagate drives.
scsi_da.h: Add a definition for the new long block defect
format.
Add bit and mask definitions for the new extended
physical sector and bytes from index defect
formats.
Add a prototype for the new scsi_read_defects() CDB
building function.
scsi_da.c: Add a new scsi_read_defects() CDB building function.
camcontrol(8) was previously composing CDBs manually.
This is long overdue.
camcontrol.c: Revamp the camcontrol defects subcommand. We now
go through multiple stages in trying to get defect
data off the drive while avoiding various drive
firmware quirks.
We start off by requesting the defect header with
the 10 byte command. If we're in summary mode (-s)
and the drive reports fewer defects than can be
represented in the 10 byte header, we're done.
Otherwise, we know that we need to issue the
12 byte command if the drive reports the maximum
number of defects.
If we're in summary mode, we're done if we get a
good response back when asking for the 12 byte header.
If the user has asked for the full list, then we
use the address descriptor index field in the 12
byte CDB to step through the list in 64K chunks.
64K is small enough to work with most any ancient
or modern SCSI controller.
Add support for printing the new long block defect
format, as well as the extended physical sector and
bytes from index formats. I don't have any drives
that support the new formats.
Add a hexadecimal output format that can be turned
on with -X.
Add a quiet mode (-q) that can be turned on with
the summary mode (-s) to just print out a number.
Revamp the error detection and recovery code for
the defects command to work with HGST drives.
Call the new scsi_read_defects() CDB building
function instead of rolling the CDB ourselves.
Pay attention to the residual from the defect list
request when printing it out, so we don't run off
the end of the list.
Use the new scsi_nv library routines to convert
from strings to numbers and back.
camcontrol.8: Document the new defect formats (longblock, extbfi,
extphys) and command line options (-q, -s, -S and
-X) for the defects subcommand.
Explain a little more about what drives generally
do and don't support.
Sponsored by: Spectra Logic
MFC after: 1 week
devq_openings counter lost its meaning after allocation queues has gone.
held counter is still meaningful, but problematic to update due to separate
locking of CCB allocation and queuing.
To fix that replace devq_openings counter with allocated counter. held is
now calculated on request as difference between number of allocated, queued
and active CCBs.
MFC after: 1 month
camcontrol(8) now supports a new 'persist' subcommand that allows users to
issue SCSI PERSISTENT RESERVE IN / OUT commands.
sbin/camcontrol/Makefile:
Add persist.c.
sbin/camcontrol/persist.c:
New persistent reservation support for camcontrol(8).
We have support for all known operation modes for PERSISTENT RESERVE
IN and PERSISTENT RESERVE OUT.
exceptions noted above.
sbin/camcontrol/camcontrol.8:
Document the new 'persist' subcommand.
In the section on the Transport ID (-I) option, explain what
Transport IDs for each protocol should look like. At some point
some of this information could probably get moved off in a
separate man page, either on Transport IDs alone or a man page
documenting the Transport ID parsing code.
Add a number of examples of persistent reservation commands.
Persistent Reservations are complex enough that the average user
probably won't be able to get the commands exactly right by just
reading the man page. These examples show a few basic and
advanced examples of how to use persistent reservations.
sbin/camcontrol/camcontrol.h:
Move the definition for camcontrol_optret here, so we can use it
for the persistent reservation code.
Add a definition for the new scsipersist() function.
sbin/camcontrol/camcontrol.c:
Add 'persist' to the list of subcommands.
Document 'persist' in the help text.
sys/cam/scsi/scsi_all.c:
Add the scsi_persistent_reserve_in() and
scsi_persistent_reserve_out() CCB building functions.
Add a new function, scsi_transportid_sbuf(). This takes a
SCSI Transport ID (documented in SPC-4), and prints it to
an sbuf(9). There are some transports (like ATA, USB, and
SSA) for which there is no transport defined. We need to
come up with a reasonable thing to do if we're presented
with a Transport ID that claims to be for one of those
protocols.
Add new routines scsi_get_nv() and scsi_nv_to_str().
These functions do a table lookup to go between a string and an
integer. There are lots of table lookups needed in the
persistent reservation code in camcontrol(8).
Add a new function, scsi_parse_transportid(), along with leaf node
functions to parse:
FC, 1394 and SAS (scsi_parse_transportid_64bit())
iSCSI (scsi_parse_transportid_iscsi())
SPI (scsi_parse_transportid_spi())
RDMA (scsi_parse_transportid_rdma())
PCIe (scsi_parse_transportid_sop())
Transport IDs. Given a string with the general form proto,id these
functions create a SCSI Transport ID structure.
sys/cam/scsi/scsi_all.h:
Update the various persistent reservation data structures to
SPC4r36l, but also rename some fields that were previously
obsolete with the proper names from older SCSI specs. This
allows using older, obsolete persistent reservation types when
desired.
Add function prototypes for the new persistent reservation CCB
building functions.
Add a data strucure for the READ FULL STATUS service action
of the PERSISTENT RESERVE IN command.
Add Transport ID structures for all protocols described in SPC-4.
Add a new series of SCSI_PROTO_XXX definitions, and
redefine other defines in terms of these new definitions.
Add a prototype for scsi_transportid_sbuf().
Change a couple of "obsolete" persistent reservation data
structure fields into something more meaningful, based on
what the field was called when it was defined in the spec.
(e.g. SPC, SPC-2, etc.)
Create a new define, SPRI_MAX_LEN, for the maximum allocation
length allowed for the PERSISTENT RESERVE IN command.
Add data structures and enumerations for the new name/value
translation functions.
Add data structures for SCSI over PCIe Routing IDs.
Bring the PERSISTENT RESERVE OUT Register and Move parameter list
structure (struct scsi_per_res_out_parms) up to date with SPC-4.
Add a data structure for the transport IDs that can optionally be
appended to the basic PERSISTENT RESERVE OUT parameter list.
Move SCSI protocol macro definitions out of the VPD page 0x83
definition and combine them with the more up to date protocol
definitions higher in the file.
Add function prototypes for scsi_nv_to_str(), scsi_get_nv(),
scsi_parse_transportid_64bit(), scsi_parse_transportid_spi(),
scsi_parse_transportid_rdma(), scsi_parse_transportid_iscsi(),
scsi_parse_transportid_sop(), and scsi_parse_transportid().
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
If an expander returns 0x00 (no device attached) in the ATTACHED DEVICE
field of the SMP DISCOVER response, ignore the value of ATTACHED SAS
ADDRESS, because it is invalid. Some expanders zero out the address
when the attached device is removed, but others do not. Section
9.4.3.10 of the SAS Protocol Layer 2 revision 04b does not require them
to do so.
Approved by: ken (mentor)
MFC after: 3 weeks
disks such as SSD's
Adds the ability to run ATA commands via the SCSI ATA Pass-Through(16) comand
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
In addition to adding `static' where possible:
- bin/date: Move `retval' into extern.h to make it visible to date.c.
- bin/ed: Move globally used variables into ed.h.
- sbin/camcontrol: Move `verbose' into camcontrol.h and fix shadow warnings.
- usr.bin/calendar: Remove unneeded variables.
- usr.bin/chat: Make `line' local instead of global.
- usr.bin/elfdump: Comment out unneeded function.
- usr.bin/rlogin: Use _Noreturn instead of __dead2.
- usr.bin/tset: Pull `Ospeed' into extern.h.
- usr.sbin/mfiutil: Put global variables in mfiutil.h.
- usr.sbin/pkg: Remove unused `os_corres'.
- usr.sbin/quotaon, usr.sbin/repquota: Remove unused `qfname'.
Initialize devlist.dev_queue tail queue early enough before its any
potential traversal in freebusdevlist() when in smpphylist error path.
Reported by: Pavel Polyakov <bsd kobyla org> (on irc)
Reviewed by: ken
MFC after: 5 days
'error' variable to zero, to avoid returning garbage in several cases.
This fixes the following clang 3.2 warnings:
sbin/camcontrol/camcontrol.c:4634:8: warning: variable 'error' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (amt_written == -1) {
^~~~~~~~~~~~~~~~~
sbin/camcontrol/camcontrol.c:4656:10: note: uninitialized use occurs here
return (error);
^~~~~
sbin/camcontrol/camcontrol.c:4619:7: warning: variable 'error' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (fd_response == 0) {
^~~~~~~~~~~~~~~~
sbin/camcontrol/camcontrol.c:4656:10: note: uninitialized use occurs here
return (error);
^~~~~
sbin/camcontrol/camcontrol.c:4617:6: warning: variable 'error' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (((ccb->ccb_h.status & CAM_STATUS_MASK) == CAM_REQ_CMP)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sbin/camcontrol/camcontrol.c:4656:10: note: uninitialized use occurs here
return (error);
^~~~~
MFC after: 1 week
defect information it has before grabbing the full defect list.
This works around a bug with some Hitachi drives that generate data overrun
errors when they are asked for more defect data than they have.
The change is done in a spec-compliant way, so it should have no negative
impact on drives that don't have this issue.
This is based on work originally done at Sandvine.
scsi_da.h: Add a define for the maximum amount of data that can be
contained in a defect list.
camcontrol.c: Update the readdefects() function to issue an initial
command to determine the length of the defect list, and
then use that length in the request for the full defect
list.
camcontrol.8: Add a note that some drives will report 0 defects available
if you don't request either the PLIST or GLIST.
Submitted by: Mark Johnston <markjdb@gmail.com> (original version)
MFC after: 3 days
ATA/SATA transport. The detection logic is automatic, so it should Just
Work. While here, also improve the progress meter that is displayed
during firmware download.
Submitted by: Alistair Crooks
Obtained from: Netflix, Inc.
MFC after: 3 days
- Add low-level support for SATA Enclosure Management Bridge (SEMB)
devices -- SATA equivalents of the SCSI SES/SAF-TE devices.
- Add some utility functions for SCSI SAF-TE devices access.
Sponsored by: iXsystems, Inc.
data changes.
cam_ccb.h: Add a new advanced information type, CDAI_TYPE_RCAPLONG,
for long read capacity data.
cam_xpt_internal.h:
Add a read capacity data pointer and length to struct cam_ed.
cam_xpt.c: Free the read capacity buffer when a device goes away.
While we're here, make sure we don't leak memory for other
malloced fields in struct cam_ed.
scsi_all.c: Update the scsi_read_capacity_16() to take a uint8_t * and
a length instead of just a pointer to the parameter data
structure. This will hopefully make this function somewhat
immune to future changes in the parameter data.
scsi_all.h: Add some extra bit definitions to struct
scsi_read_capacity_data_long, and bump up the structure
size to the full size specified by SBC-3.
Change the prototype for scsi_read_capacity_16().
scsi_da.c: Register changes in read capacity data with the transport
layer. This allows the transport layer to send out an
async notification to interested parties. Update the
dasetgeom() API.
Use scsi_extract_sense_len() instead of
scsi_extract_sense().
scsi_xpt.c: Add support for the new CDAI_TYPE_RCAPLONG advanced
information type.
Make sure we set the physpath pointer to NULL after freeing
it. This allows blindly freeing it in the struct cam_ed
destructor.
sys/param.h: Bump __FreeBSD_version from 1000005 to 1000006 to make it
easier for third party drivers to determine that the read
capacity data async notification is available.
camcontrol.c,
mptutil/mpt_cam.c:
Update these for the new scsi_read_capacity_16() argument
structure.
Sponsored by: Spectra Logic
