/*- * Copyright (c) 1992, 1993 Erik Forsberg. * Copyright (c) 1996, 1997 Kazutaka YOKOTA. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * THIS SOFTWARE IS PROVIDED BY ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN * NO EVENT SHALL I BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD$ */ /* * Ported to 386bsd Oct 17, 1992 * Sandi Donno, Computer Science, University of Cape Town, South Africa * Please send bug reports to sandi@cs.uct.ac.za * * Thanks are also due to Rick Macklem, rick@snowhite.cis.uoguelph.ca - * although I was only partially successful in getting the alpha release * of his "driver for the Logitech and ATI Inport Bus mice for use with * 386bsd and the X386 port" to work with my Microsoft mouse, I nevertheless * found his code to be an invaluable reference when porting this driver * to 386bsd. * * Further modifications for latest 386BSD+patchkit and port to NetBSD, * Andrew Herbert - 8 June 1993 * * Cloned from the Microsoft Bus Mouse driver, also by Erik Forsberg, by * Andrew Herbert - 12 June 1993 * * Modified for PS/2 mouse by Charles Hannum * - 13 June 1993 * * Modified for PS/2 AUX mouse by Shoji Yuen * - 24 October 1993 * * Hardware access routines and probe logic rewritten by * Kazutaka Yokota * - 3, 14, 22 October 1996. * - 12 November 1996. IOCTLs and rearranging `psmread', `psmioctl'... * - 14, 30 November 1996. Uses `kbdio.c'. * - 13 December 1996. Uses queuing version of `kbdio.c'. * - January/February 1997. Tweaked probe logic for * HiNote UltraII/Latitude/Armada laptops. * - 30 July 1997. Added APM support. * - 5 March 1997. Defined driver configuration flags (PSM_CONFIG_XXX). * Improved sync check logic. * Vendor specific support routines. */ #include "opt_psm.h" #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* * Driver specific options: the following options may be set by * `options' statements in the kernel configuration file. */ /* debugging */ #ifndef PSM_DEBUG #define PSM_DEBUG 0 /* logging: 0: none, 1: brief, 2: verbose */ #endif /* end of driver specific options */ /* input queue */ #define PSM_BUFSIZE 960 #define PSM_SMALLBUFSIZE 240 /* operation levels */ #define PSM_LEVEL_BASE 0 #define PSM_LEVEL_STANDARD 1 #define PSM_LEVEL_NATIVE 2 #define PSM_LEVEL_MIN PSM_LEVEL_BASE #define PSM_LEVEL_MAX PSM_LEVEL_NATIVE /* Logitech PS2++ protocol */ #define MOUSE_PS2PLUS_CHECKBITS(b) \ ((((b[2] & 0x03) << 2) | 0x02) == (b[1] & 0x0f)) #define MOUSE_PS2PLUS_PACKET_TYPE(b) \ (((b[0] & 0x30) >> 2) | ((b[1] & 0x30) >> 4)) /* some macros */ #define PSM_UNIT(dev) (minor(dev) >> 1) #define PSM_NBLOCKIO(dev) (minor(dev) & 1) #define PSM_MKMINOR(unit,block) (((unit) << 1) | ((block) ? 0:1)) #ifndef max #define max(x,y) ((x) > (y) ? (x) : (y)) #endif #ifndef min #define min(x,y) ((x) < (y) ? (x) : (y)) #endif #define abs(x) (((x) < 0) ? -(x) : (x)) /* ring buffer */ typedef struct ringbuf { int count; /* # of valid elements in the buffer */ int head; /* head pointer */ int tail; /* tail poiner */ unsigned char buf[PSM_BUFSIZE]; } ringbuf_t; /* driver control block */ struct psm_softc { /* Driver status information */ struct selinfo rsel; /* Process selecting for Input */ unsigned char state; /* Mouse driver state */ int config; /* driver configuration flags */ int flags; /* other flags */ KBDC kbdc; /* handle to access the keyboard controller */ struct resource *intr; /* IRQ resource */ void *ih; /* interrupt handle */ mousehw_t hw; /* hardware information */ mousemode_t mode; /* operation mode */ mousemode_t dflt_mode; /* default operation mode */ mousestatus_t status; /* accumulated mouse movement */ ringbuf_t queue; /* mouse status queue */ unsigned char ipacket[16]; /* interim input buffer */ int inputbytes; /* # of bytes in the input buffer */ int button; /* the latest button state */ int xold; /* previous absolute X position */ int yold; /* previous absolute Y position */ int watchdog; /* watchdog timer flag */ struct callout_handle callout; /* watchdog timer call out */ dev_t dev; dev_t bdev; }; devclass_t psm_devclass; #define PSM_SOFTC(unit) ((struct psm_softc*)devclass_get_softc(psm_devclass, unit)) /* driver state flags (state) */ #define PSM_VALID 0x80 #define PSM_OPEN 1 /* Device is open */ #define PSM_ASLP 2 /* Waiting for mouse data */ /* driver configuration flags (config) */ #define PSM_CONFIG_RESOLUTION 0x000f /* resolution */ #define PSM_CONFIG_ACCEL 0x00f0 /* acceleration factor */ #define PSM_CONFIG_NOCHECKSYNC 0x0100 /* disable sync. test */ #define PSM_CONFIG_NOIDPROBE 0x0200 /* disable mouse model probe */ #define PSM_CONFIG_NORESET 0x0400 /* don't reset the mouse */ #define PSM_CONFIG_FORCETAP 0x0800 /* assume `tap' action exists */ #define PSM_CONFIG_IGNPORTERROR 0x1000 /* ignore error in aux port test */ #define PSM_CONFIG_HOOKRESUME 0x2000 /* hook the system resume event */ #define PSM_CONFIG_INITAFTERSUSPEND 0x4000 /* init the device at the resume event */ #define PSM_CONFIG_SYNCHACK 0x8000 /* enable `out-of-sync' hack */ #define PSM_CONFIG_FLAGS (PSM_CONFIG_RESOLUTION \ | PSM_CONFIG_ACCEL \ | PSM_CONFIG_NOCHECKSYNC \ | PSM_CONFIG_SYNCHACK \ | PSM_CONFIG_NOIDPROBE \ | PSM_CONFIG_NORESET \ | PSM_CONFIG_FORCETAP \ | PSM_CONFIG_IGNPORTERROR \ | PSM_CONFIG_HOOKRESUME \ | PSM_CONFIG_INITAFTERSUSPEND) /* other flags (flags) */ #define PSM_FLAGS_FINGERDOWN 0x0001 /* VersaPad finger down */ /* for backward compatibility */ #define OLD_MOUSE_GETHWINFO _IOR('M', 1, old_mousehw_t) #define OLD_MOUSE_GETMODE _IOR('M', 2, old_mousemode_t) #define OLD_MOUSE_SETMODE _IOW('M', 3, old_mousemode_t) typedef struct old_mousehw { int buttons; int iftype; int type; int hwid; } old_mousehw_t; typedef struct old_mousemode { int protocol; int rate; int resolution; int accelfactor; } old_mousemode_t; /* packet formatting function */ typedef int packetfunc_t __P((struct psm_softc *, unsigned char *, int *, int, mousestatus_t *)); /* function prototypes */ static void psmidentify __P((driver_t *, device_t)); static int psmprobe __P((device_t)); static int psmattach __P((device_t)); static int psmdetach __P((device_t)); static int psmresume __P((device_t)); static d_open_t psmopen; static d_close_t psmclose; static d_read_t psmread; static d_ioctl_t psmioctl; static d_poll_t psmpoll; static int enable_aux_dev __P((KBDC)); static int disable_aux_dev __P((KBDC)); static int get_mouse_status __P((KBDC, int *, int, int)); static int get_aux_id __P((KBDC)); static int set_mouse_sampling_rate __P((KBDC, int)); static int set_mouse_scaling __P((KBDC, int)); static int set_mouse_resolution __P((KBDC, int)); static int set_mouse_mode __P((KBDC)); static int get_mouse_buttons __P((KBDC)); static int is_a_mouse __P((int)); static void recover_from_error __P((KBDC)); static int restore_controller __P((KBDC, int)); static int reinitialize __P((int, mousemode_t *)); static int doopen __P((int, int)); static char *model_name __P((int)); static void psmintr __P((void *)); static void psmtimeout __P((void *)); /* vendor specific features */ typedef int probefunc_t __P((struct psm_softc *)); static int mouse_id_proc1 __P((KBDC, int, int, int *)); static int mouse_ext_command __P((KBDC, int)); static probefunc_t enable_groller; static probefunc_t enable_gmouse; static probefunc_t enable_aglide; static probefunc_t enable_kmouse; static probefunc_t enable_msexplorer; static probefunc_t enable_msintelli; static probefunc_t enable_4dmouse; static probefunc_t enable_4dplus; static probefunc_t enable_mmanplus; static probefunc_t enable_versapad; static int tame_mouse __P((struct psm_softc *, mousestatus_t *, unsigned char *)); static struct { int model; unsigned char syncmask; int packetsize; probefunc_t *probefunc; } vendortype[] = { /* * WARNING: the order of probe is very important. Don't mess it * unless you know what you are doing. */ { MOUSE_MODEL_NET, /* Genius NetMouse */ 0x08, MOUSE_PS2INTELLI_PACKETSIZE, enable_gmouse, }, { MOUSE_MODEL_NETSCROLL, /* Genius NetScroll */ 0xc8, 6, enable_groller, }, { MOUSE_MODEL_MOUSEMANPLUS, /* Logitech MouseMan+ */ 0x08, MOUSE_PS2_PACKETSIZE, enable_mmanplus, }, { MOUSE_MODEL_EXPLORER, /* Microsoft IntelliMouse Explorer */ 0x08, MOUSE_PS2INTELLI_PACKETSIZE, enable_msexplorer, }, { MOUSE_MODEL_4D, /* A4 Tech 4D Mouse */ 0x08, MOUSE_4D_PACKETSIZE, enable_4dmouse, }, { MOUSE_MODEL_4DPLUS, /* A4 Tech 4D+ Mouse */ 0xc8, MOUSE_4DPLUS_PACKETSIZE, enable_4dplus, }, { MOUSE_MODEL_INTELLI, /* Microsoft IntelliMouse */ 0x08, MOUSE_PS2INTELLI_PACKETSIZE, enable_msintelli, }, { MOUSE_MODEL_GLIDEPOINT, /* ALPS GlidePoint */ 0xc0, MOUSE_PS2_PACKETSIZE, enable_aglide, }, { MOUSE_MODEL_THINK, /* Kensignton ThinkingMouse */ 0x80, MOUSE_PS2_PACKETSIZE, enable_kmouse, }, { MOUSE_MODEL_VERSAPAD, /* Interlink electronics VersaPad */ 0xe8, MOUSE_PS2VERSA_PACKETSIZE, enable_versapad, }, { MOUSE_MODEL_GENERIC, 0xc0, MOUSE_PS2_PACKETSIZE, NULL, }, }; #define GENERIC_MOUSE_ENTRY ((sizeof(vendortype) / sizeof(*vendortype)) - 1) /* device driver declarateion */ static device_method_t psm_methods[] = { /* Device interface */ DEVMETHOD(device_identify, psmidentify), DEVMETHOD(device_probe, psmprobe), DEVMETHOD(device_attach, psmattach), DEVMETHOD(device_detach, psmdetach), DEVMETHOD(device_resume, psmresume), { 0, 0 } }; static driver_t psm_driver = { "psm", psm_methods, sizeof(struct psm_softc), }; #define CDEV_MAJOR 21 static struct cdevsw psm_cdevsw = { /* open */ psmopen, /* close */ psmclose, /* read */ psmread, /* write */ nowrite, /* ioctl */ psmioctl, /* poll */ psmpoll, /* mmap */ nommap, /* strategy */ nostrategy, /* name */ "psm", /* maj */ CDEV_MAJOR, /* dump */ nodump, /* psize */ nopsize, /* flags */ 0, }; /* debug message level */ static int verbose = PSM_DEBUG; /* device I/O routines */ static int enable_aux_dev(KBDC kbdc) { int res; res = send_aux_command(kbdc, PSMC_ENABLE_DEV); if (verbose >= 2) log(LOG_DEBUG, "psm: ENABLE_DEV return code:%04x\n", res); return (res == PSM_ACK); } static int disable_aux_dev(KBDC kbdc) { int res; res = send_aux_command(kbdc, PSMC_DISABLE_DEV); if (verbose >= 2) log(LOG_DEBUG, "psm: DISABLE_DEV return code:%04x\n", res); return (res == PSM_ACK); } static int get_mouse_status(KBDC kbdc, int *status, int flag, int len) { int cmd; int res; int i; switch (flag) { case 0: default: cmd = PSMC_SEND_DEV_STATUS; break; case 1: cmd = PSMC_SEND_DEV_DATA; break; } empty_aux_buffer(kbdc, 5); res = send_aux_command(kbdc, cmd); if (verbose >= 2) log(LOG_DEBUG, "psm: SEND_AUX_DEV_%s return code:%04x\n", (flag == 1) ? "DATA" : "STATUS", res); if (res != PSM_ACK) return 0; for (i = 0; i < len; ++i) { status[i] = read_aux_data(kbdc); if (status[i] < 0) break; } if (verbose) { log(LOG_DEBUG, "psm: %s %02x %02x %02x\n", (flag == 1) ? "data" : "status", status[0], status[1], status[2]); } return i; } static int get_aux_id(KBDC kbdc) { int res; int id; empty_aux_buffer(kbdc, 5); res = send_aux_command(kbdc, PSMC_SEND_DEV_ID); if (verbose >= 2) log(LOG_DEBUG, "psm: SEND_DEV_ID return code:%04x\n", res); if (res != PSM_ACK) return (-1); /* 10ms delay */ DELAY(10000); id = read_aux_data(kbdc); if (verbose >= 2) log(LOG_DEBUG, "psm: device ID: %04x\n", id); return id; } static int set_mouse_sampling_rate(KBDC kbdc, int rate) { int res; res = send_aux_command_and_data(kbdc, PSMC_SET_SAMPLING_RATE, rate); if (verbose >= 2) log(LOG_DEBUG, "psm: SET_SAMPLING_RATE (%d) %04x\n", rate, res); return ((res == PSM_ACK) ? rate : -1); } static int set_mouse_scaling(KBDC kbdc, int scale) { int res; switch (scale) { case 1: default: scale = PSMC_SET_SCALING11; break; case 2: scale = PSMC_SET_SCALING21; break; } res = send_aux_command(kbdc, scale); if (verbose >= 2) log(LOG_DEBUG, "psm: SET_SCALING%s return code:%04x\n", (scale == PSMC_SET_SCALING21) ? "21" : "11", res); return (res == PSM_ACK); } /* `val' must be 0 through PSMD_MAX_RESOLUTION */ static int set_mouse_resolution(KBDC kbdc, int val) { int res; res = send_aux_command_and_data(kbdc, PSMC_SET_RESOLUTION, val); if (verbose >= 2) log(LOG_DEBUG, "psm: SET_RESOLUTION (%d) %04x\n", val, res); return ((res == PSM_ACK) ? val : -1); } /* * NOTE: once `set_mouse_mode()' is called, the mouse device must be * re-enabled by calling `enable_aux_dev()' */ static int set_mouse_mode(KBDC kbdc) { int res; res = send_aux_command(kbdc, PSMC_SET_STREAM_MODE); if (verbose >= 2) log(LOG_DEBUG, "psm: SET_STREAM_MODE return code:%04x\n", res); return (res == PSM_ACK); } static int get_mouse_buttons(KBDC kbdc) { int c = 2; /* assume two buttons by default */ int status[3]; /* * NOTE: a special sequence to obtain Logitech Mouse specific * information: set resolution to 25 ppi, set scaling to 1:1, set * scaling to 1:1, set scaling to 1:1. Then the second byte of the * mouse status bytes is the number of available buttons. * Some manufactures also support this sequence. */ if (set_mouse_resolution(kbdc, PSMD_RES_LOW) != PSMD_RES_LOW) return c; if (set_mouse_scaling(kbdc, 1) && set_mouse_scaling(kbdc, 1) && set_mouse_scaling(kbdc, 1) && (get_mouse_status(kbdc, status, 0, 3) >= 3)) { if (status[1] != 0) return status[1]; } return c; } /* misc subroutines */ /* * Someday, I will get the complete list of valid pointing devices and * their IDs... XXX */ static int is_a_mouse(int id) { #if 0 static int valid_ids[] = { PSM_MOUSE_ID, /* mouse */ PSM_BALLPOINT_ID, /* ballpoint device */ PSM_INTELLI_ID, /* Intellimouse */ PSM_EXPLORER_ID, /* Intellimouse Explorer */ -1 /* end of table */ }; int i; for (i = 0; valid_ids[i] >= 0; ++i) if (valid_ids[i] == id) return TRUE; return FALSE; #else return TRUE; #endif } static char * model_name(int model) { static struct { int model_code; char *model_name; } models[] = { { MOUSE_MODEL_NETSCROLL, "NetScroll" }, { MOUSE_MODEL_NET, "NetMouse/NetScroll Optical" }, { MOUSE_MODEL_GLIDEPOINT, "GlidePoint" }, { MOUSE_MODEL_THINK, "ThinkingMouse" }, { MOUSE_MODEL_INTELLI, "IntelliMouse" }, { MOUSE_MODEL_MOUSEMANPLUS, "MouseMan+" }, { MOUSE_MODEL_VERSAPAD, "VersaPad" }, { MOUSE_MODEL_EXPLORER, "IntelliMouse Explorer" }, { MOUSE_MODEL_4D, "4D Mouse" }, { MOUSE_MODEL_4DPLUS, "4D+ Mouse" }, { MOUSE_MODEL_GENERIC, "Generic PS/2 mouse" }, { MOUSE_MODEL_UNKNOWN, NULL }, }; int i; for (i = 0; models[i].model_code != MOUSE_MODEL_UNKNOWN; ++i) { if (models[i].model_code == model) return models[i].model_name; } return "Unknown"; } static void recover_from_error(KBDC kbdc) { /* discard anything left in the output buffer */ empty_both_buffers(kbdc, 10); #if 0 /* * NOTE: KBDC_RESET_KBD may not restore the communication between the * keyboard and the controller. */ reset_kbd(kbdc); #else /* * NOTE: somehow diagnostic and keyboard port test commands bring the * keyboard back. */ if (!test_controller(kbdc)) log(LOG_ERR, "psm: keyboard controller failed.\n"); /* if there isn't a keyboard in the system, the following error is OK */ if (test_kbd_port(kbdc) != 0) { if (verbose) log(LOG_ERR, "psm: keyboard port failed.\n"); } #endif } static int restore_controller(KBDC kbdc, int command_byte) { empty_both_buffers(kbdc, 10); if (!set_controller_command_byte(kbdc, 0xff, command_byte)) { log(LOG_ERR, "psm: failed to restore the keyboard controller " "command byte.\n"); empty_both_buffers(kbdc, 10); return FALSE; } else { empty_both_buffers(kbdc, 10); return TRUE; } } /* * Re-initialize the aux port and device. The aux port must be enabled * and its interrupt must be disabled before calling this routine. * The aux device will be disabled before returning. * The keyboard controller must be locked via `kbdc_lock()' before * calling this routine. */ static int reinitialize(int unit, mousemode_t *mode) { struct psm_softc *sc = PSM_SOFTC(unit); KBDC kbdc = sc->kbdc; int stat[3]; int i; switch((i = test_aux_port(kbdc))) { case 1: /* ignore this error */ case PSM_ACK: if (verbose) log(LOG_DEBUG, "psm%d: strange result for test aux port (%d).\n", unit, i); /* fall though */ case 0: /* no error */ break; case -1: /* time out */ default: /* error */ recover_from_error(kbdc); if (sc->config & PSM_CONFIG_IGNPORTERROR) break; log(LOG_ERR, "psm%d: the aux port is not functioning (%d).\n", unit, i); return FALSE; } if (sc->config & PSM_CONFIG_NORESET) { /* * Don't try to reset the pointing device. It may possibly be * left in the unknown state, though... */ } else { /* * NOTE: some controllers appears to hang the `keyboard' when * the aux port doesn't exist and `PSMC_RESET_DEV' is issued. */ if (!reset_aux_dev(kbdc)) { recover_from_error(kbdc); log(LOG_ERR, "psm%d: failed to reset the aux device.\n", unit); return FALSE; } } /* * both the aux port and the aux device is functioning, see * if the device can be enabled. */ if (!enable_aux_dev(kbdc) || !disable_aux_dev(kbdc)) { log(LOG_ERR, "psm%d: failed to enable the aux device.\n", unit); return FALSE; } empty_both_buffers(kbdc, 10); /* remove stray data if any */ if (sc->config & PSM_CONFIG_NOIDPROBE) { i = GENERIC_MOUSE_ENTRY; } else { /* FIXME: hardware ID, mouse buttons? */ /* other parameters */ for (i = 0; vendortype[i].probefunc != NULL; ++i) { if ((*vendortype[i].probefunc)(sc)) { if (verbose >= 2) log(LOG_ERR, "psm%d: found %s\n", unit, model_name(vendortype[i].model)); break; } } } sc->hw.model = vendortype[i].model; sc->mode.packetsize = vendortype[i].packetsize; /* set mouse parameters */ if (mode != (mousemode_t *)NULL) { if (mode->rate > 0) mode->rate = set_mouse_sampling_rate(kbdc, mode->rate); if (mode->resolution >= 0) mode->resolution = set_mouse_resolution(kbdc, mode->resolution); set_mouse_scaling(kbdc, 1); set_mouse_mode(kbdc); } /* request a data packet and extract sync. bits */ if (get_mouse_status(kbdc, stat, 1, 3) < 3) { log(LOG_DEBUG, "psm%d: failed to get data (reinitialize).\n", unit); sc->mode.syncmask[0] = 0; } else { sc->mode.syncmask[1] = stat[0] & sc->mode.syncmask[0]; /* syncbits */ /* the NetScroll Mouse will send three more bytes... Ignore them */ empty_aux_buffer(kbdc, 5); } /* just check the status of the mouse */ if (get_mouse_status(kbdc, stat, 0, 3) < 3) log(LOG_DEBUG, "psm%d: failed to get status (reinitialize).\n", unit); return TRUE; } static int doopen(int unit, int command_byte) { struct psm_softc *sc = PSM_SOFTC(unit); int stat[3]; /* enable the mouse device */ if (!enable_aux_dev(sc->kbdc)) { /* MOUSE ERROR: failed to enable the mouse because: * 1) the mouse is faulty, * 2) the mouse has been removed(!?) * In the latter case, the keyboard may have hung, and need * recovery procedure... */ recover_from_error(sc->kbdc); #if 0 /* FIXME: we could reset the mouse here and try to enable * it again. But it will take long time and it's not a good * idea to disable the keyboard that long... */ if (!reinitialize(unit, &sc->mode) || !enable_aux_dev(sc->kbdc)) { recover_from_error(sc->kbdc); #else { #endif restore_controller(sc->kbdc, command_byte); /* mark this device is no longer available */ sc->state &= ~PSM_VALID; log(LOG_ERR, "psm%d: failed to enable the device (doopen).\n", unit); return (EIO); } } if (get_mouse_status(sc->kbdc, stat, 0, 3) < 3) log(LOG_DEBUG, "psm%d: failed to get status (doopen).\n", unit); /* enable the aux port and interrupt */ if (!set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), (command_byte & KBD_KBD_CONTROL_BITS) | KBD_ENABLE_AUX_PORT | KBD_ENABLE_AUX_INT)) { /* CONTROLLER ERROR */ disable_aux_dev(sc->kbdc); restore_controller(sc->kbdc, command_byte); log(LOG_ERR, "psm%d: failed to enable the aux interrupt (doopen).\n", unit); return (EIO); } /* start the watchdog timer */ sc->watchdog = FALSE; sc->callout = timeout(psmtimeout, (void *)(uintptr_t)unit, hz*2); return (0); } /* psm driver entry points */ static void psmidentify(driver_t *driver, device_t parent) { /* always add at least one child */ BUS_ADD_CHILD(parent, KBDC_RID_AUX, driver->name, 0); } #define endprobe(v) { if (bootverbose) \ --verbose; \ kbdc_set_device_mask(sc->kbdc, mask); \ kbdc_lock(sc->kbdc, FALSE); \ return (v); \ } static int psmprobe(device_t dev) { int unit = device_get_unit(dev); struct psm_softc *sc = device_get_softc(dev); int stat[3]; int command_byte; int mask; int rid; int i; #if 0 kbdc_debug(TRUE); #endif /* see if IRQ is available */ rid = KBDC_RID_AUX; sc->intr = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0, 1, RF_SHAREABLE | RF_ACTIVE); if (sc->intr == NULL) { if (bootverbose) device_printf(dev, "unable to allocate IRQ\n"); return (ENXIO); } bus_release_resource(dev, SYS_RES_IRQ, rid, sc->intr); sc->kbdc = atkbdc_open(device_get_unit(device_get_parent(dev))); sc->config = device_get_flags(dev) & PSM_CONFIG_FLAGS; /* XXX: for backward compatibility */ #if defined(PSM_HOOKRESUME) || defined(PSM_HOOKAPM) sc->config |= #ifdef PSM_RESETAFTERSUSPEND PSM_CONFIG_HOOKRESUME | PSM_CONFIG_INITAFTERSUSPEND; #else PSM_CONFIG_HOOKRESUME; #endif #endif /* PSM_HOOKRESUME | PSM_HOOKAPM */ sc->flags = 0; if (bootverbose) ++verbose; device_set_desc(dev, "PS/2 Mouse"); if (!kbdc_lock(sc->kbdc, TRUE)) { printf("psm%d: unable to lock the controller.\n", unit); if (bootverbose) --verbose; return (ENXIO); } /* * NOTE: two bits in the command byte controls the operation of the * aux port (mouse port): the aux port disable bit (bit 5) and the aux * port interrupt (IRQ 12) enable bit (bit 2). */ /* discard anything left after the keyboard initialization */ empty_both_buffers(sc->kbdc, 10); /* save the current command byte; it will be used later */ mask = kbdc_get_device_mask(sc->kbdc) & ~KBD_AUX_CONTROL_BITS; command_byte = get_controller_command_byte(sc->kbdc); if (verbose) printf("psm%d: current command byte:%04x\n", unit, command_byte); if (command_byte == -1) { /* CONTROLLER ERROR */ printf("psm%d: unable to get the current command byte value.\n", unit); endprobe(ENXIO); } /* * disable the keyboard port while probing the aux port, which must be * enabled during this routine */ if (!set_controller_command_byte(sc->kbdc, KBD_KBD_CONTROL_BITS | KBD_AUX_CONTROL_BITS, KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT | KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { /* * this is CONTROLLER ERROR; I don't know how to recover * from this error... */ restore_controller(sc->kbdc, command_byte); printf("psm%d: unable to set the command byte.\n", unit); endprobe(ENXIO); } write_controller_command(sc->kbdc, KBDC_ENABLE_AUX_PORT); /* * NOTE: `test_aux_port()' is designed to return with zero if the aux * port exists and is functioning. However, some controllers appears * to respond with zero even when the aux port doesn't exist. (It may * be that this is only the case when the controller DOES have the aux * port but the port is not wired on the motherboard.) The keyboard * controllers without the port, such as the original AT, are * supporsed to return with an error code or simply time out. In any * case, we have to continue probing the port even when the controller * passes this test. * * XXX: some controllers erroneously return the error code 1 when * it has the perfectly functional aux port. We have to ignore this * error code. Even if the controller HAS error with the aux port, * it will be detected later... * XXX: another incompatible controller returns PSM_ACK (0xfa)... */ switch ((i = test_aux_port(sc->kbdc))) { case 1: /* ignore this error */ case PSM_ACK: if (verbose) printf("psm%d: strange result for test aux port (%d).\n", unit, i); /* fall though */ case 0: /* no error */ break; case -1: /* time out */ default: /* error */ recover_from_error(sc->kbdc); if (sc->config & PSM_CONFIG_IGNPORTERROR) break; restore_controller(sc->kbdc, command_byte); if (verbose) printf("psm%d: the aux port is not functioning (%d).\n", unit, i); endprobe(ENXIO); } if (sc->config & PSM_CONFIG_NORESET) { /* * Don't try to reset the pointing device. It may possibly be * left in the unknown state, though... */ } else { /* * NOTE: some controllers appears to hang the `keyboard' when the aux * port doesn't exist and `PSMC_RESET_DEV' is issued. */ if (!reset_aux_dev(sc->kbdc)) { recover_from_error(sc->kbdc); restore_controller(sc->kbdc, command_byte); if (verbose) printf("psm%d: failed to reset the aux device.\n", unit); endprobe(ENXIO); } } /* * both the aux port and the aux device is functioning, see if the * device can be enabled. NOTE: when enabled, the device will start * sending data; we shall immediately disable the device once we know * the device can be enabled. */ if (!enable_aux_dev(sc->kbdc) || !disable_aux_dev(sc->kbdc)) { /* MOUSE ERROR */ recover_from_error(sc->kbdc); restore_controller(sc->kbdc, command_byte); if (verbose) printf("psm%d: failed to enable the aux device.\n", unit); endprobe(ENXIO); } /* save the default values after reset */ if (get_mouse_status(sc->kbdc, stat, 0, 3) >= 3) { sc->dflt_mode.rate = sc->mode.rate = stat[2]; sc->dflt_mode.resolution = sc->mode.resolution = stat[1]; } else { sc->dflt_mode.rate = sc->mode.rate = -1; sc->dflt_mode.resolution = sc->mode.resolution = -1; } /* hardware information */ sc->hw.iftype = MOUSE_IF_PS2; /* verify the device is a mouse */ sc->hw.hwid = get_aux_id(sc->kbdc); if (!is_a_mouse(sc->hw.hwid)) { restore_controller(sc->kbdc, command_byte); if (verbose) printf("psm%d: unknown device type (%d).\n", unit, sc->hw.hwid); endprobe(ENXIO); } switch (sc->hw.hwid) { case PSM_BALLPOINT_ID: sc->hw.type = MOUSE_TRACKBALL; break; case PSM_MOUSE_ID: case PSM_INTELLI_ID: case PSM_EXPLORER_ID: case PSM_4DMOUSE_ID: case PSM_4DPLUS_ID: sc->hw.type = MOUSE_MOUSE; break; default: sc->hw.type = MOUSE_UNKNOWN; break; } if (sc->config & PSM_CONFIG_NOIDPROBE) { sc->hw.buttons = 2; i = GENERIC_MOUSE_ENTRY; } else { /* # of buttons */ sc->hw.buttons = get_mouse_buttons(sc->kbdc); /* other parameters */ for (i = 0; vendortype[i].probefunc != NULL; ++i) { if ((*vendortype[i].probefunc)(sc)) { if (verbose >= 2) printf("psm%d: found %s\n", unit, model_name(vendortype[i].model)); break; } } } sc->hw.model = vendortype[i].model; sc->dflt_mode.level = PSM_LEVEL_BASE; sc->dflt_mode.packetsize = MOUSE_PS2_PACKETSIZE; sc->dflt_mode.accelfactor = (sc->config & PSM_CONFIG_ACCEL) >> 4; if (sc->config & PSM_CONFIG_NOCHECKSYNC) sc->dflt_mode.syncmask[0] = 0; else sc->dflt_mode.syncmask[0] = vendortype[i].syncmask; if (sc->config & PSM_CONFIG_FORCETAP) sc->mode.syncmask[0] &= ~MOUSE_PS2_TAP; sc->dflt_mode.syncmask[1] = 0; /* syncbits */ sc->mode = sc->dflt_mode; sc->mode.packetsize = vendortype[i].packetsize; /* set mouse parameters */ #if 0 /* * A version of Logitech FirstMouse+ won't report wheel movement, * if SET_DEFAULTS is sent... Don't use this command. * This fix was found by Takashi Nishida. */ i = send_aux_command(sc->kbdc, PSMC_SET_DEFAULTS); if (verbose >= 2) printf("psm%d: SET_DEFAULTS return code:%04x\n", unit, i); #endif if (sc->config & PSM_CONFIG_RESOLUTION) { sc->mode.resolution = set_mouse_resolution(sc->kbdc, (sc->config & PSM_CONFIG_RESOLUTION) - 1); } else if (sc->mode.resolution >= 0) { sc->mode.resolution = set_mouse_resolution(sc->kbdc, sc->dflt_mode.resolution); } if (sc->mode.rate > 0) { sc->mode.rate = set_mouse_sampling_rate(sc->kbdc, sc->dflt_mode.rate); } set_mouse_scaling(sc->kbdc, 1); /* request a data packet and extract sync. bits */ if (get_mouse_status(sc->kbdc, stat, 1, 3) < 3) { printf("psm%d: failed to get data.\n", unit); sc->mode.syncmask[0] = 0; } else { sc->mode.syncmask[1] = stat[0] & sc->mode.syncmask[0]; /* syncbits */ /* the NetScroll Mouse will send three more bytes... Ignore them */ empty_aux_buffer(sc->kbdc, 5); } /* just check the status of the mouse */ /* * NOTE: XXX there are some arcane controller/mouse combinations out * there, which hung the controller unless there is data transmission * after ACK from the mouse. */ if (get_mouse_status(sc->kbdc, stat, 0, 3) < 3) { printf("psm%d: failed to get status.\n", unit); } else { /* * When in its native mode, some mice operate with different * default parameters than in the PS/2 compatible mode. */ sc->dflt_mode.rate = sc->mode.rate = stat[2]; sc->dflt_mode.resolution = sc->mode.resolution = stat[1]; } /* disable the aux port for now... */ if (!set_controller_command_byte(sc->kbdc, KBD_KBD_CONTROL_BITS | KBD_AUX_CONTROL_BITS, (command_byte & KBD_KBD_CONTROL_BITS) | KBD_DISABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { /* * this is CONTROLLER ERROR; I don't know the proper way to * recover from this error... */ restore_controller(sc->kbdc, command_byte); printf("psm%d: unable to set the command byte.\n", unit); endprobe(ENXIO); } /* done */ kbdc_set_device_mask(sc->kbdc, mask | KBD_AUX_CONTROL_BITS); kbdc_lock(sc->kbdc, FALSE); return (0); } static int psmattach(device_t dev) { int unit = device_get_unit(dev); struct psm_softc *sc = device_get_softc(dev); int error; int rid; if (sc == NULL) /* shouldn't happen */ return (ENXIO); /* Setup initial state */ sc->state = PSM_VALID; callout_handle_init(&sc->callout); /* Setup our interrupt handler */ rid = KBDC_RID_AUX; sc->intr = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0, 1, RF_SHAREABLE | RF_ACTIVE); if (sc->intr == NULL) return (ENXIO); error = bus_setup_intr(dev, sc->intr, INTR_TYPE_TTY, psmintr, sc, &sc->ih); if (error) { bus_release_resource(dev, SYS_RES_IRQ, rid, sc->intr); return (error); } /* Done */ sc->dev = make_dev(&psm_cdevsw, PSM_MKMINOR(unit, FALSE), 0, 0, 0666, "psm%d", unit); sc->bdev = make_dev(&psm_cdevsw, PSM_MKMINOR(unit, TRUE), 0, 0, 0666, "bpsm%d", unit); if (!verbose) { printf("psm%d: model %s, device ID %d\n", unit, model_name(sc->hw.model), sc->hw.hwid & 0x00ff); } else { printf("psm%d: model %s, device ID %d-%02x, %d buttons\n", unit, model_name(sc->hw.model), sc->hw.hwid & 0x00ff, sc->hw.hwid >> 8, sc->hw.buttons); printf("psm%d: config:%08x, flags:%08x, packet size:%d\n", unit, sc->config, sc->flags, sc->mode.packetsize); printf("psm%d: syncmask:%02x, syncbits:%02x\n", unit, sc->mode.syncmask[0], sc->mode.syncmask[1]); } if (bootverbose) --verbose; return (0); } static int psmdetach(device_t dev) { struct psm_softc *sc; int rid; sc = device_get_softc(dev); if (sc->state & PSM_OPEN) return EBUSY; rid = KBDC_RID_AUX; bus_teardown_intr(dev, sc->intr, sc->ih); bus_release_resource(dev, SYS_RES_IRQ, rid, sc->intr); destroy_dev(sc->dev); destroy_dev(sc->bdev); return 0; } static int psmopen(dev_t dev, int flag, int fmt, struct thread *td) { int unit = PSM_UNIT(dev); struct psm_softc *sc; int command_byte; int err; int s; /* Get device data */ sc = PSM_SOFTC(unit); if ((sc == NULL) || (sc->state & PSM_VALID) == 0) /* the device is no longer valid/functioning */ return (ENXIO); /* Disallow multiple opens */ if (sc->state & PSM_OPEN) return (EBUSY); device_busy(devclass_get_device(psm_devclass, unit)); /* Initialize state */ sc->rsel.si_flags = 0; sc->rsel.si_pid = 0; sc->mode.level = sc->dflt_mode.level; sc->mode.protocol = sc->dflt_mode.protocol; sc->watchdog = FALSE; /* flush the event queue */ sc->queue.count = 0; sc->queue.head = 0; sc->queue.tail = 0; sc->status.flags = 0; sc->status.button = 0; sc->status.obutton = 0; sc->status.dx = 0; sc->status.dy = 0; sc->status.dz = 0; sc->button = 0; /* empty input buffer */ bzero(sc->ipacket, sizeof(sc->ipacket)); sc->inputbytes = 0; /* don't let timeout routines in the keyboard driver to poll the kbdc */ if (!kbdc_lock(sc->kbdc, TRUE)) return (EIO); /* save the current controller command byte */ s = spltty(); command_byte = get_controller_command_byte(sc->kbdc); /* enable the aux port and temporalily disable the keyboard */ if ((command_byte == -1) || !set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT | KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { /* CONTROLLER ERROR; do you know how to get out of this? */ kbdc_lock(sc->kbdc, FALSE); splx(s); log(LOG_ERR, "psm%d: unable to set the command byte (psmopen).\n", unit); return (EIO); } /* * Now that the keyboard controller is told not to generate * the keyboard and mouse interrupts, call `splx()' to allow * the other tty interrupts. The clock interrupt may also occur, * but timeout routines will be blocked by the poll flag set * via `kbdc_lock()' */ splx(s); /* enable the mouse device */ err = doopen(unit, command_byte); /* done */ if (err == 0) sc->state |= PSM_OPEN; kbdc_lock(sc->kbdc, FALSE); return (err); } static int psmclose(dev_t dev, int flag, int fmt, struct thread *td) { int unit = PSM_UNIT(dev); struct psm_softc *sc = PSM_SOFTC(unit); int stat[3]; int command_byte; int s; /* don't let timeout routines in the keyboard driver to poll the kbdc */ if (!kbdc_lock(sc->kbdc, TRUE)) return (EIO); /* save the current controller command byte */ s = spltty(); command_byte = get_controller_command_byte(sc->kbdc); if (command_byte == -1) { kbdc_lock(sc->kbdc, FALSE); splx(s); return (EIO); } /* disable the aux interrupt and temporalily disable the keyboard */ if (!set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT | KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { log(LOG_ERR, "psm%d: failed to disable the aux int (psmclose).\n", unit); /* CONTROLLER ERROR; * NOTE: we shall force our way through. Because the only * ill effect we shall see is that we may not be able * to read ACK from the mouse, and it doesn't matter much * so long as the mouse will accept the DISABLE command. */ } splx(s); /* stop the watchdog timer */ untimeout(psmtimeout, (void *)(uintptr_t)unit, sc->callout); callout_handle_init(&sc->callout); /* remove anything left in the output buffer */ empty_aux_buffer(sc->kbdc, 10); /* disable the aux device, port and interrupt */ if (sc->state & PSM_VALID) { if (!disable_aux_dev(sc->kbdc)) { /* MOUSE ERROR; * NOTE: we don't return error and continue, pretending * we have successfully disabled the device. It's OK because * the interrupt routine will discard any data from the mouse * hereafter. */ log(LOG_ERR, "psm%d: failed to disable the device (psmclose).\n", unit); } if (get_mouse_status(sc->kbdc, stat, 0, 3) < 3) log(LOG_DEBUG, "psm%d: failed to get status (psmclose).\n", unit); } if (!set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), (command_byte & KBD_KBD_CONTROL_BITS) | KBD_DISABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { /* CONTROLLER ERROR; * we shall ignore this error; see the above comment. */ log(LOG_ERR, "psm%d: failed to disable the aux port (psmclose).\n", unit); } /* remove anything left in the output buffer */ empty_aux_buffer(sc->kbdc, 10); /* close is almost always successful */ sc->state &= ~PSM_OPEN; kbdc_lock(sc->kbdc, FALSE); device_unbusy(devclass_get_device(psm_devclass, unit)); return (0); } static int tame_mouse(struct psm_softc *sc, mousestatus_t *status, unsigned char *buf) { static unsigned char butmapps2[8] = { 0, MOUSE_PS2_BUTTON1DOWN, MOUSE_PS2_BUTTON2DOWN, MOUSE_PS2_BUTTON1DOWN | MOUSE_PS2_BUTTON2DOWN, MOUSE_PS2_BUTTON3DOWN, MOUSE_PS2_BUTTON1DOWN | MOUSE_PS2_BUTTON3DOWN, MOUSE_PS2_BUTTON2DOWN | MOUSE_PS2_BUTTON3DOWN, MOUSE_PS2_BUTTON1DOWN | MOUSE_PS2_BUTTON2DOWN | MOUSE_PS2_BUTTON3DOWN, }; static unsigned char butmapmsc[8] = { MOUSE_MSC_BUTTON1UP | MOUSE_MSC_BUTTON2UP | MOUSE_MSC_BUTTON3UP, MOUSE_MSC_BUTTON2UP | MOUSE_MSC_BUTTON3UP, MOUSE_MSC_BUTTON1UP | MOUSE_MSC_BUTTON3UP, MOUSE_MSC_BUTTON3UP, MOUSE_MSC_BUTTON1UP | MOUSE_MSC_BUTTON2UP, MOUSE_MSC_BUTTON2UP, MOUSE_MSC_BUTTON1UP, 0, }; int mapped; int i; if (sc->mode.level == PSM_LEVEL_BASE) { mapped = status->button & ~MOUSE_BUTTON4DOWN; if (status->button & MOUSE_BUTTON4DOWN) mapped |= MOUSE_BUTTON1DOWN; status->button = mapped; buf[0] = MOUSE_PS2_SYNC | butmapps2[mapped & MOUSE_STDBUTTONS]; i = max(min(status->dx, 255), -256); if (i < 0) buf[0] |= MOUSE_PS2_XNEG; buf[1] = i; i = max(min(status->dy, 255), -256); if (i < 0) buf[0] |= MOUSE_PS2_YNEG; buf[2] = i; return MOUSE_PS2_PACKETSIZE; } else if (sc->mode.level == PSM_LEVEL_STANDARD) { buf[0] = MOUSE_MSC_SYNC | butmapmsc[status->button & MOUSE_STDBUTTONS]; i = max(min(status->dx, 255), -256); buf[1] = i >> 1; buf[3] = i - buf[1]; i = max(min(status->dy, 255), -256); buf[2] = i >> 1; buf[4] = i - buf[2]; i = max(min(status->dz, 127), -128); buf[5] = (i >> 1) & 0x7f; buf[6] = (i - (i >> 1)) & 0x7f; buf[7] = (~status->button >> 3) & 0x7f; return MOUSE_SYS_PACKETSIZE; } return sc->inputbytes;; } static int psmread(dev_t dev, struct uio *uio, int flag) { register struct psm_softc *sc = PSM_SOFTC(PSM_UNIT(dev)); unsigned char buf[PSM_SMALLBUFSIZE]; int error = 0; int s; int l; if ((sc->state & PSM_VALID) == 0) return EIO; /* block until mouse activity occured */ s = spltty(); while (sc->queue.count <= 0) { if (PSM_NBLOCKIO(dev)) { splx(s); return EWOULDBLOCK; } sc->state |= PSM_ASLP; error = tsleep((caddr_t) sc, PZERO | PCATCH, "psmrea", 0); sc->state &= ~PSM_ASLP; if (error) { splx(s); return error; } else if ((sc->state & PSM_VALID) == 0) { /* the device disappeared! */ splx(s); return EIO; } } splx(s); /* copy data to the user land */ while ((sc->queue.count > 0) && (uio->uio_resid > 0)) { s = spltty(); l = min(sc->queue.count, uio->uio_resid); if (l > sizeof(buf)) l = sizeof(buf); if (l > sizeof(sc->queue.buf) - sc->queue.head) { bcopy(&sc->queue.buf[sc->queue.head], &buf[0], sizeof(sc->queue.buf) - sc->queue.head); bcopy(&sc->queue.buf[0], &buf[sizeof(sc->queue.buf) - sc->queue.head], l - (sizeof(sc->queue.buf) - sc->queue.head)); } else { bcopy(&sc->queue.buf[sc->queue.head], &buf[0], l); } sc->queue.count -= l; sc->queue.head = (sc->queue.head + l) % sizeof(sc->queue.buf); splx(s); error = uiomove(buf, l, uio); if (error) break; } return error; } static int block_mouse_data(struct psm_softc *sc, int *c) { int s; if (!kbdc_lock(sc->kbdc, TRUE)) return EIO; s = spltty(); *c = get_controller_command_byte(sc->kbdc); if ((*c == -1) || !set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT | KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { /* this is CONTROLLER ERROR */ splx(s); kbdc_lock(sc->kbdc, FALSE); return EIO; } /* * The device may be in the middle of status data transmission. * The transmission will be interrupted, thus, incomplete status * data must be discarded. Although the aux interrupt is disabled * at the keyboard controller level, at most one aux interrupt * may have already been pending and a data byte is in the * output buffer; throw it away. Note that the second argument * to `empty_aux_buffer()' is zero, so that the call will just * flush the internal queue. * `psmintr()' will be invoked after `splx()' if an interrupt is * pending; it will see no data and returns immediately. */ empty_aux_buffer(sc->kbdc, 0); /* flush the queue */ read_aux_data_no_wait(sc->kbdc); /* throw away data if any */ sc->inputbytes = 0; splx(s); return 0; } static int unblock_mouse_data(struct psm_softc *sc, int c) { int error = 0; /* * We may have seen a part of status data during `set_mouse_XXX()'. * they have been queued; flush it. */ empty_aux_buffer(sc->kbdc, 0); /* restore ports and interrupt */ if (!set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), c & (KBD_KBD_CONTROL_BITS | KBD_AUX_CONTROL_BITS))) { /* CONTROLLER ERROR; this is serious, we may have * been left with the inaccessible keyboard and * the disabled mouse interrupt. */ error = EIO; } kbdc_lock(sc->kbdc, FALSE); return error; } static int psmioctl(dev_t dev, u_long cmd, caddr_t addr, int flag, struct thread *td) { struct psm_softc *sc = PSM_SOFTC(PSM_UNIT(dev)); mousemode_t mode; mousestatus_t status; #if (defined(MOUSE_GETVARS)) mousevar_t *var; #endif mousedata_t *data; int stat[3]; int command_byte; int error = 0; int s; /* Perform IOCTL command */ switch (cmd) { case OLD_MOUSE_GETHWINFO: s = spltty(); ((old_mousehw_t *)addr)->buttons = sc->hw.buttons; ((old_mousehw_t *)addr)->iftype = sc->hw.iftype; ((old_mousehw_t *)addr)->type = sc->hw.type; ((old_mousehw_t *)addr)->hwid = sc->hw.hwid & 0x00ff; splx(s); break; case MOUSE_GETHWINFO: s = spltty(); *(mousehw_t *)addr = sc->hw; if (sc->mode.level == PSM_LEVEL_BASE) ((mousehw_t *)addr)->model = MOUSE_MODEL_GENERIC; splx(s); break; case OLD_MOUSE_GETMODE: s = spltty(); switch (sc->mode.level) { case PSM_LEVEL_BASE: ((old_mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2; break; case PSM_LEVEL_STANDARD: ((old_mousemode_t *)addr)->protocol = MOUSE_PROTO_SYSMOUSE; break; case PSM_LEVEL_NATIVE: ((old_mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2; break; } ((old_mousemode_t *)addr)->rate = sc->mode.rate; ((old_mousemode_t *)addr)->resolution = sc->mode.resolution; ((old_mousemode_t *)addr)->accelfactor = sc->mode.accelfactor; splx(s); break; case MOUSE_GETMODE: s = spltty(); *(mousemode_t *)addr = sc->mode; ((mousemode_t *)addr)->resolution = MOUSE_RES_LOW - sc->mode.resolution; switch (sc->mode.level) { case PSM_LEVEL_BASE: ((mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2; ((mousemode_t *)addr)->packetsize = MOUSE_PS2_PACKETSIZE; break; case PSM_LEVEL_STANDARD: ((mousemode_t *)addr)->protocol = MOUSE_PROTO_SYSMOUSE; ((mousemode_t *)addr)->packetsize = MOUSE_SYS_PACKETSIZE; ((mousemode_t *)addr)->syncmask[0] = MOUSE_SYS_SYNCMASK; ((mousemode_t *)addr)->syncmask[1] = MOUSE_SYS_SYNC; break; case PSM_LEVEL_NATIVE: /* FIXME: this isn't quite correct... XXX */ ((mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2; break; } splx(s); break; case OLD_MOUSE_SETMODE: case MOUSE_SETMODE: if (cmd == OLD_MOUSE_SETMODE) { mode.rate = ((old_mousemode_t *)addr)->rate; /* * resolution old I/F new I/F * default 0 0 * low 1 -2 * medium low 2 -3 * medium high 3 -4 * high 4 -5 */ if (((old_mousemode_t *)addr)->resolution > 0) mode.resolution = -((old_mousemode_t *)addr)->resolution - 1; mode.accelfactor = ((old_mousemode_t *)addr)->accelfactor; mode.level = -1; } else { mode = *(mousemode_t *)addr; } /* adjust and validate parameters. */ if (mode.rate > UCHAR_MAX) return EINVAL; if (mode.rate == 0) mode.rate = sc->dflt_mode.rate; else if (mode.rate == -1) /* don't change the current setting */ ; else if (mode.rate < 0) return EINVAL; if (mode.resolution >= UCHAR_MAX) return EINVAL; if (mode.resolution >= 200) mode.resolution = MOUSE_RES_HIGH; else if (mode.resolution >= 100) mode.resolution = MOUSE_RES_MEDIUMHIGH; else if (mode.resolution >= 50) mode.resolution = MOUSE_RES_MEDIUMLOW; else if (mode.resolution > 0) mode.resolution = MOUSE_RES_LOW; if (mode.resolution == MOUSE_RES_DEFAULT) mode.resolution = sc->dflt_mode.resolution; else if (mode.resolution == -1) /* don't change the current setting */ ; else if (mode.resolution < 0) /* MOUSE_RES_LOW/MEDIUM/HIGH */ mode.resolution = MOUSE_RES_LOW - mode.resolution; if (mode.level == -1) /* don't change the current setting */ mode.level = sc->mode.level; else if ((mode.level < PSM_LEVEL_MIN) || (mode.level > PSM_LEVEL_MAX)) return EINVAL; if (mode.accelfactor == -1) /* don't change the current setting */ mode.accelfactor = sc->mode.accelfactor; else if (mode.accelfactor < 0) return EINVAL; /* don't allow anybody to poll the keyboard controller */ error = block_mouse_data(sc, &command_byte); if (error) return error; /* set mouse parameters */ if (mode.rate > 0) mode.rate = set_mouse_sampling_rate(sc->kbdc, mode.rate); if (mode.resolution >= 0) mode.resolution = set_mouse_resolution(sc->kbdc, mode.resolution); set_mouse_scaling(sc->kbdc, 1); get_mouse_status(sc->kbdc, stat, 0, 3); s = spltty(); sc->mode.rate = mode.rate; sc->mode.resolution = mode.resolution; sc->mode.accelfactor = mode.accelfactor; sc->mode.level = mode.level; splx(s); unblock_mouse_data(sc, command_byte); break; case MOUSE_GETLEVEL: *(int *)addr = sc->mode.level; break; case MOUSE_SETLEVEL: if ((*(int *)addr < PSM_LEVEL_MIN) || (*(int *)addr > PSM_LEVEL_MAX)) return EINVAL; sc->mode.level = *(int *)addr; break; case MOUSE_GETSTATUS: s = spltty(); status = sc->status; sc->status.flags = 0; sc->status.obutton = sc->status.button; sc->status.button = 0; sc->status.dx = 0; sc->status.dy = 0; sc->status.dz = 0; splx(s); *(mousestatus_t *)addr = status; break; #if (defined(MOUSE_GETVARS)) case MOUSE_GETVARS: var = (mousevar_t *)addr; bzero(var, sizeof(*var)); s = spltty(); var->var[0] = MOUSE_VARS_PS2_SIG; var->var[1] = sc->config; var->var[2] = sc->flags; splx(s); break; case MOUSE_SETVARS: return ENODEV; #endif /* MOUSE_GETVARS */ case MOUSE_READSTATE: case MOUSE_READDATA: data = (mousedata_t *)addr; if (data->len > sizeof(data->buf)/sizeof(data->buf[0])) return EINVAL; error = block_mouse_data(sc, &command_byte); if (error) return error; if ((data->len = get_mouse_status(sc->kbdc, data->buf, (cmd == MOUSE_READDATA) ? 1 : 0, data->len)) <= 0) error = EIO; unblock_mouse_data(sc, command_byte); break; #if (defined(MOUSE_SETRESOLUTION)) case MOUSE_SETRESOLUTION: mode.resolution = *(int *)addr; if (mode.resolution >= UCHAR_MAX) return EINVAL; else if (mode.resolution >= 200) mode.resolution = MOUSE_RES_HIGH; else if (mode.resolution >= 100) mode.resolution = MOUSE_RES_MEDIUMHIGH; else if (mode.resolution >= 50) mode.resolution = MOUSE_RES_MEDIUMLOW; else if (mode.resolution > 0) mode.resolution = MOUSE_RES_LOW; if (mode.resolution == MOUSE_RES_DEFAULT) mode.resolution = sc->dflt_mode.resolution; else if (mode.resolution == -1) mode.resolution = sc->mode.resolution; else if (mode.resolution < 0) /* MOUSE_RES_LOW/MEDIUM/HIGH */ mode.resolution = MOUSE_RES_LOW - mode.resolution; error = block_mouse_data(sc, &command_byte); if (error) return error; sc->mode.resolution = set_mouse_resolution(sc->kbdc, mode.resolution); if (sc->mode.resolution != mode.resolution) error = EIO; unblock_mouse_data(sc, command_byte); break; #endif /* MOUSE_SETRESOLUTION */ #if (defined(MOUSE_SETRATE)) case MOUSE_SETRATE: mode.rate = *(int *)addr; if (mode.rate > UCHAR_MAX) return EINVAL; if (mode.rate == 0) mode.rate = sc->dflt_mode.rate; else if (mode.rate < 0) mode.rate = sc->mode.rate; error = block_mouse_data(sc, &command_byte); if (error) return error; sc->mode.rate = set_mouse_sampling_rate(sc->kbdc, mode.rate); if (sc->mode.rate != mode.rate) error = EIO; unblock_mouse_data(sc, command_byte); break; #endif /* MOUSE_SETRATE */ #if (defined(MOUSE_SETSCALING)) case MOUSE_SETSCALING: if ((*(int *)addr <= 0) || (*(int *)addr > 2)) return EINVAL; error = block_mouse_data(sc, &command_byte); if (error) return error; if (!set_mouse_scaling(sc->kbdc, *(int *)addr)) error = EIO; unblock_mouse_data(sc, command_byte); break; #endif /* MOUSE_SETSCALING */ #if (defined(MOUSE_GETHWID)) case MOUSE_GETHWID: error = block_mouse_data(sc, &command_byte); if (error) return error; sc->hw.hwid &= ~0x00ff; sc->hw.hwid |= get_aux_id(sc->kbdc); *(int *)addr = sc->hw.hwid & 0x00ff; unblock_mouse_data(sc, command_byte); break; #endif /* MOUSE_GETHWID */ default: return ENOTTY; } return error; } static void psmtimeout(void *arg) { struct psm_softc *sc; int unit; int s; unit = (int)(uintptr_t)arg; sc = devclass_get_softc(psm_devclass, unit); s = spltty(); if (sc->watchdog && kbdc_lock(sc->kbdc, TRUE)) { if (verbose >= 4) log(LOG_DEBUG, "psm%d: lost interrupt?\n", unit); psmintr(sc); kbdc_lock(sc->kbdc, FALSE); } sc->watchdog = TRUE; splx(s); sc->callout = timeout(psmtimeout, (void *)(uintptr_t)unit, hz); } static void psmintr(void *arg) { /* * the table to turn PS/2 mouse button bits (MOUSE_PS2_BUTTON?DOWN) * into `mousestatus' button bits (MOUSE_BUTTON?DOWN). */ static int butmap[8] = { 0, MOUSE_BUTTON1DOWN, MOUSE_BUTTON3DOWN, MOUSE_BUTTON1DOWN | MOUSE_BUTTON3DOWN, MOUSE_BUTTON2DOWN, MOUSE_BUTTON1DOWN | MOUSE_BUTTON2DOWN, MOUSE_BUTTON2DOWN | MOUSE_BUTTON3DOWN, MOUSE_BUTTON1DOWN | MOUSE_BUTTON2DOWN | MOUSE_BUTTON3DOWN }; static int butmap_versapad[8] = { 0, MOUSE_BUTTON3DOWN, 0, MOUSE_BUTTON3DOWN, MOUSE_BUTTON1DOWN, MOUSE_BUTTON1DOWN | MOUSE_BUTTON3DOWN, MOUSE_BUTTON1DOWN, MOUSE_BUTTON1DOWN | MOUSE_BUTTON3DOWN }; register struct psm_softc *sc = arg; mousestatus_t ms; int x, y, z; int c; int l; int x0, y0; /* read until there is nothing to read */ while((c = read_aux_data_no_wait(sc->kbdc)) != -1) { /* discard the byte if the device is not open */ if ((sc->state & PSM_OPEN) == 0) continue; sc->ipacket[sc->inputbytes++] = c; if (sc->inputbytes < sc->mode.packetsize) continue; #if 0 log(LOG_DEBUG, "psmintr: %02x %02x %02x %02x %02x %02x\n", sc->ipacket[0], sc->ipacket[1], sc->ipacket[2], sc->ipacket[3], sc->ipacket[4], sc->ipacket[5]); #endif c = sc->ipacket[0]; if ((c & sc->mode.syncmask[0]) != sc->mode.syncmask[1]) { log(LOG_DEBUG, "psmintr: out of sync (%04x != %04x).\n", c & sc->mode.syncmask[0], sc->mode.syncmask[1]); sc->inputbytes = 0; if (sc->config & PSM_CONFIG_SYNCHACK) { /* * XXX: this is a grotesque hack to get us out of * dreaded "out of sync" error. */ log(LOG_DEBUG, "psmintr: re-enable the mouse.\n"); disable_aux_dev(sc->kbdc); enable_aux_dev(sc->kbdc); } continue; } /* * A kludge for Kensington device! * The MSB of the horizontal count appears to be stored in * a strange place. */ if (sc->hw.model == MOUSE_MODEL_THINK) sc->ipacket[1] |= (c & MOUSE_PS2_XOVERFLOW) ? 0x80 : 0; /* ignore the overflow bits... */ x = (c & MOUSE_PS2_XNEG) ? sc->ipacket[1] - 256 : sc->ipacket[1]; y = (c & MOUSE_PS2_YNEG) ? sc->ipacket[2] - 256 : sc->ipacket[2]; z = 0; ms.obutton = sc->button; /* previous button state */ ms.button = butmap[c & MOUSE_PS2_BUTTONS]; /* `tapping' action */ if (sc->config & PSM_CONFIG_FORCETAP) ms.button |= ((c & MOUSE_PS2_TAP)) ? 0 : MOUSE_BUTTON4DOWN; switch (sc->hw.model) { case MOUSE_MODEL_EXPLORER: /* * b7 b6 b5 b4 b3 b2 b1 b0 * byte 1: oy ox sy sx 1 M R L * byte 2: x x x x x x x x * byte 3: y y y y y y y y * byte 4: * * S2 S1 s d2 d1 d0 * * L, M, R, S1, S2: left, middle, right and side buttons * s: wheel data sign bit * d2-d0: wheel data */ z = (sc->ipacket[3] & MOUSE_EXPLORER_ZNEG) ? (sc->ipacket[3] & 0x0f) - 16 : (sc->ipacket[3] & 0x0f); ms.button |= (sc->ipacket[3] & MOUSE_EXPLORER_BUTTON4DOWN) ? MOUSE_BUTTON4DOWN : 0; ms.button |= (sc->ipacket[3] & MOUSE_EXPLORER_BUTTON5DOWN) ? MOUSE_BUTTON5DOWN : 0; break; case MOUSE_MODEL_INTELLI: case MOUSE_MODEL_NET: /* wheel data is in the fourth byte */ z = (char)sc->ipacket[3]; /* some mice may send 7 when there is no Z movement?! XXX */ if ((z >= 7) || (z <= -7)) z = 0; /* some compatible mice have additional buttons */ ms.button |= (c & MOUSE_PS2INTELLI_BUTTON4DOWN) ? MOUSE_BUTTON4DOWN : 0; ms.button |= (c & MOUSE_PS2INTELLI_BUTTON5DOWN) ? MOUSE_BUTTON5DOWN : 0; break; case MOUSE_MODEL_MOUSEMANPLUS: /* * PS2++ protocl packet * * b7 b6 b5 b4 b3 b2 b1 b0 * byte 1: * 1 p3 p2 1 * * * * byte 2: c1 c2 p1 p0 d1 d0 1 0 * * p3-p0: packet type * c1, c2: c1 & c2 == 1, if p2 == 0 * c1 & c2 == 0, if p2 == 1 * * packet type: 0 (device type) * See comments in enable_mmanplus() below. * * packet type: 1 (wheel data) * * b7 b6 b5 b4 b3 b2 b1 b0 * byte 3: h * B5 B4 s d2 d1 d0 * * h: 1, if horizontal roller data * 0, if vertical roller data * B4, B5: button 4 and 5 * s: sign bit * d2-d0: roller data * * packet type: 2 (reserved) */ if (((c & MOUSE_PS2PLUS_SYNCMASK) == MOUSE_PS2PLUS_SYNC) && (abs(x) > 191) && MOUSE_PS2PLUS_CHECKBITS(sc->ipacket)) { /* the extended data packet encodes button and wheel events */ switch (MOUSE_PS2PLUS_PACKET_TYPE(sc->ipacket)) { case 1: /* wheel data packet */ x = y = 0; if (sc->ipacket[2] & 0x80) { /* horizontal roller count - ignore it XXX*/ } else { /* vertical roller count */ z = (sc->ipacket[2] & MOUSE_PS2PLUS_ZNEG) ? (sc->ipacket[2] & 0x0f) - 16 : (sc->ipacket[2] & 0x0f); } ms.button |= (sc->ipacket[2] & MOUSE_PS2PLUS_BUTTON4DOWN) ? MOUSE_BUTTON4DOWN : 0; ms.button |= (sc->ipacket[2] & MOUSE_PS2PLUS_BUTTON5DOWN) ? MOUSE_BUTTON5DOWN : 0; break; case 2: /* this packet type is reserved by Logitech... */ /* * IBM ScrollPoint Mouse uses this packet type to * encode both vertical and horizontal scroll movement. */ x = y = 0; /* horizontal count */ if (sc->ipacket[2] & 0x0f) z = (sc->ipacket[2] & MOUSE_SPOINT_WNEG) ? -2 : 2; /* vertical count */ if (sc->ipacket[2] & 0xf0) z = (sc->ipacket[2] & MOUSE_SPOINT_ZNEG) ? -1 : 1; #if 0 /* vertical count */ z = (sc->ipacket[2] & MOUSE_SPOINT_ZNEG) ? ((sc->ipacket[2] >> 4) & 0x0f) - 16 : ((sc->ipacket[2] >> 4) & 0x0f); /* horizontal count */ w = (sc->ipacket[2] & MOUSE_SPOINT_WNEG) ? (sc->ipacket[2] & 0x0f) - 16 : (sc->ipacket[2] & 0x0f); #endif break; case 0: /* device type packet - shouldn't happen */ /* FALL THROUGH */ default: x = y = 0; ms.button = ms.obutton; if (bootverbose) log(LOG_DEBUG, "psmintr: unknown PS2++ packet type %d: " "0x%02x 0x%02x 0x%02x\n", MOUSE_PS2PLUS_PACKET_TYPE(sc->ipacket), sc->ipacket[0], sc->ipacket[1], sc->ipacket[2]); break; } } else { /* preserve button states */ ms.button |= ms.obutton & MOUSE_EXTBUTTONS; } break; case MOUSE_MODEL_GLIDEPOINT: /* `tapping' action */ ms.button |= ((c & MOUSE_PS2_TAP)) ? 0 : MOUSE_BUTTON4DOWN; break; case MOUSE_MODEL_NETSCROLL: /* three addtional bytes encode buttons and wheel events */ ms.button |= (sc->ipacket[3] & MOUSE_PS2_BUTTON3DOWN) ? MOUSE_BUTTON4DOWN : 0; ms.button |= (sc->ipacket[3] & MOUSE_PS2_BUTTON1DOWN) ? MOUSE_BUTTON5DOWN : 0; z = (sc->ipacket[3] & MOUSE_PS2_XNEG) ? sc->ipacket[4] - 256 : sc->ipacket[4]; break; case MOUSE_MODEL_THINK: /* the fourth button state in the first byte */ ms.button |= (c & MOUSE_PS2_TAP) ? MOUSE_BUTTON4DOWN : 0; break; case MOUSE_MODEL_VERSAPAD: /* VersaPad PS/2 absolute mode message format * * [packet1] 7 6 5 4 3 2 1 0(LSB) * ipacket[0]: 1 1 0 A 1 L T R * ipacket[1]: H7 H6 H5 H4 H3 H2 H1 H0 * ipacket[2]: V7 V6 V5 V4 V3 V2 V1 V0 * ipacket[3]: 1 1 1 A 1 L T R * ipacket[4]:V11 V10 V9 V8 H11 H10 H9 H8 * ipacket[5]: 0 P6 P5 P4 P3 P2 P1 P0 * * [note] * R: right physical mouse button (1=on) * T: touch pad virtual button (1=tapping) * L: left physical mouse button (1=on) * A: position data is valid (1=valid) * H: horizontal data (12bit signed integer. H11 is sign bit.) * V: vertical data (12bit signed integer. V11 is sign bit.) * P: pressure data * * Tapping is mapped to MOUSE_BUTTON4. */ ms.button = butmap_versapad[c & MOUSE_PS2VERSA_BUTTONS]; ms.button |= (c & MOUSE_PS2VERSA_TAP) ? MOUSE_BUTTON4DOWN : 0; x = y = 0; if (c & MOUSE_PS2VERSA_IN_USE) { x0 = sc->ipacket[1] | (((sc->ipacket[4]) & 0x0f) << 8); y0 = sc->ipacket[2] | (((sc->ipacket[4]) & 0xf0) << 4); if (x0 & 0x800) x0 -= 0x1000; if (y0 & 0x800) y0 -= 0x1000; if (sc->flags & PSM_FLAGS_FINGERDOWN) { x = sc->xold - x0; y = y0 - sc->yold; if (x < 0) /* XXX */ x++; else if (x) x--; if (y < 0) y++; else if (y) y--; } else { sc->flags |= PSM_FLAGS_FINGERDOWN; } sc->xold = x0; sc->yold = y0; } else { sc->flags &= ~PSM_FLAGS_FINGERDOWN; } c = ((x < 0) ? MOUSE_PS2_XNEG : 0) | ((y < 0) ? MOUSE_PS2_YNEG : 0); break; case MOUSE_MODEL_4D: /* * b7 b6 b5 b4 b3 b2 b1 b0 * byte 1: s2 d2 s1 d1 1 M R L * byte 2: sx x x x x x x x * byte 3: sy y y y y y y y * * s1: wheel 1 direction * d1: wheel 1 data * s2: wheel 2 direction * d2: wheel 2 data */ x = (sc->ipacket[1] & 0x80) ? sc->ipacket[1] - 256 : sc->ipacket[1]; y = (sc->ipacket[2] & 0x80) ? sc->ipacket[2] - 256 : sc->ipacket[2]; switch (c & MOUSE_4D_WHEELBITS) { case 0x10: z = 1; break; case 0x30: z = -1; break; case 0x40: /* 2nd wheel turning right XXX */ z = 2; break; case 0xc0: /* 2nd wheel turning left XXX */ z = -2; break; } break; case MOUSE_MODEL_4DPLUS: if ((x < 16 - 256) && (y < 16 - 256)) { /* * b7 b6 b5 b4 b3 b2 b1 b0 * byte 1: 0 0 1 1 1 M R L * byte 2: 0 0 0 0 1 0 0 0 * byte 3: 0 0 0 0 S s d1 d0 * * L, M, R, S: left, middle, right and side buttons * s: wheel data sign bit * d1-d0: wheel data */ x = y = 0; if (sc->ipacket[2] & MOUSE_4DPLUS_BUTTON4DOWN) ms.button |= MOUSE_BUTTON4DOWN; z = (sc->ipacket[2] & MOUSE_4DPLUS_ZNEG) ? ((sc->ipacket[2] & 0x07) - 8) : (sc->ipacket[2] & 0x07) ; } else { /* preserve previous button states */ ms.button |= ms.obutton & MOUSE_EXTBUTTONS; } break; case MOUSE_MODEL_GENERIC: default: break; } /* scale values */ if (sc->mode.accelfactor >= 1) { if (x != 0) { x = x * x / sc->mode.accelfactor; if (x == 0) x = 1; if (c & MOUSE_PS2_XNEG) x = -x; } if (y != 0) { y = y * y / sc->mode.accelfactor; if (y == 0) y = 1; if (c & MOUSE_PS2_YNEG) y = -y; } } ms.dx = x; ms.dy = y; ms.dz = z; ms.flags = ((x || y || z) ? MOUSE_POSCHANGED : 0) | (ms.obutton ^ ms.button); if (sc->mode.level < PSM_LEVEL_NATIVE) sc->inputbytes = tame_mouse(sc, &ms, sc->ipacket); sc->status.flags |= ms.flags; sc->status.dx += ms.dx; sc->status.dy += ms.dy; sc->status.dz += ms.dz; sc->status.button = ms.button; sc->button = ms.button; sc->watchdog = FALSE; /* queue data */ if (sc->queue.count + sc->inputbytes < sizeof(sc->queue.buf)) { l = min(sc->inputbytes, sizeof(sc->queue.buf) - sc->queue.tail); bcopy(&sc->ipacket[0], &sc->queue.buf[sc->queue.tail], l); if (sc->inputbytes > l) bcopy(&sc->ipacket[l], &sc->queue.buf[0], sc->inputbytes - l); sc->queue.tail = (sc->queue.tail + sc->inputbytes) % sizeof(sc->queue.buf); sc->queue.count += sc->inputbytes; } sc->inputbytes = 0; if (sc->state & PSM_ASLP) { sc->state &= ~PSM_ASLP; wakeup((caddr_t) sc); } selwakeup(&sc->rsel); } } static int psmpoll(dev_t dev, int events, struct thread *td) { struct psm_softc *sc = PSM_SOFTC(PSM_UNIT(dev)); int s; int revents = 0; /* Return true if a mouse event available */ s = spltty(); if (events & (POLLIN | POLLRDNORM)) { if (sc->queue.count > 0) revents |= events & (POLLIN | POLLRDNORM); else selrecord(td, &sc->rsel); } splx(s); return (revents); } /* vendor/model specific routines */ static int mouse_id_proc1(KBDC kbdc, int res, int scale, int *status) { if (set_mouse_resolution(kbdc, res) != res) return FALSE; if (set_mouse_scaling(kbdc, scale) && set_mouse_scaling(kbdc, scale) && set_mouse_scaling(kbdc, scale) && (get_mouse_status(kbdc, status, 0, 3) >= 3)) return TRUE; return FALSE; } static int mouse_ext_command(KBDC kbdc, int command) { int c; c = (command >> 6) & 0x03; if (set_mouse_resolution(kbdc, c) != c) return FALSE; c = (command >> 4) & 0x03; if (set_mouse_resolution(kbdc, c) != c) return FALSE; c = (command >> 2) & 0x03; if (set_mouse_resolution(kbdc, c) != c) return FALSE; c = (command >> 0) & 0x03; if (set_mouse_resolution(kbdc, c) != c) return FALSE; return TRUE; } #if notyet /* Logitech MouseMan Cordless II */ static int enable_lcordless(struct psm_softc *sc) { int status[3]; int ch; if (!mouse_id_proc1(sc->kbdc, PSMD_RES_HIGH, 2, status)) return FALSE; if (status[1] == PSMD_RES_HIGH) return FALSE; ch = (status[0] & 0x07) - 1; /* channel # */ if ((ch <= 0) || (ch > 4)) return FALSE; /* * status[1]: always one? * status[2]: battery status? (0-100) */ return TRUE; } #endif /* notyet */ /* Genius NetScroll Mouse, MouseSystems SmartScroll Mouse */ static int enable_groller(struct psm_softc *sc) { int status[3]; /* * The special sequence to enable the fourth button and the * roller. Immediately after this sequence check status bytes. * if the mouse is NetScroll, the second and the third bytes are * '3' and 'D'. */ /* * If the mouse is an ordinary PS/2 mouse, the status bytes should * look like the following. * * byte 1 bit 7 always 0 * bit 6 stream mode (0) * bit 5 disabled (0) * bit 4 1:1 scaling (0) * bit 3 always 0 * bit 0-2 button status * byte 2 resolution (PSMD_RES_HIGH) * byte 3 report rate (?) */ if (!mouse_id_proc1(sc->kbdc, PSMD_RES_HIGH, 1, status)) return FALSE; if ((status[1] != '3') || (status[2] != 'D')) return FALSE; /* FIXME: SmartScroll Mouse has 5 buttons! XXX */ sc->hw.buttons = 4; return TRUE; } /* Genius NetMouse/NetMouse Pro, ASCII Mie Mouse, NetScroll Optical */ static int enable_gmouse(struct psm_softc *sc) { int status[3]; /* * The special sequence to enable the middle, "rubber" button. * Immediately after this sequence check status bytes. * if the mouse is NetMouse, NetMouse Pro, or ASCII MIE Mouse, * the second and the third bytes are '3' and 'U'. * NOTE: NetMouse reports that it has three buttons although it has * two buttons and a rubber button. NetMouse Pro and MIE Mouse * say they have three buttons too and they do have a button on the * side... */ if (!mouse_id_proc1(sc->kbdc, PSMD_RES_HIGH, 1, status)) return FALSE; if ((status[1] != '3') || (status[2] != 'U')) return FALSE; return TRUE; } /* ALPS GlidePoint */ static int enable_aglide(struct psm_softc *sc) { int status[3]; /* * The special sequence to obtain ALPS GlidePoint specific * information. Immediately after this sequence, status bytes will * contain something interesting. * NOTE: ALPS produces several models of GlidePoint. Some of those * do not respond to this sequence, thus, cannot be detected this way. */ if (set_mouse_sampling_rate(sc->kbdc, 100) != 100) return FALSE; if (!mouse_id_proc1(sc->kbdc, PSMD_RES_LOW, 2, status)) return FALSE; if ((status[1] == PSMD_RES_LOW) || (status[2] == 100)) return FALSE; return TRUE; } /* Kensington ThinkingMouse/Trackball */ static int enable_kmouse(struct psm_softc *sc) { static unsigned char rate[] = { 20, 60, 40, 20, 20, 60, 40, 20, 20 }; KBDC kbdc = sc->kbdc; int status[3]; int id1; int id2; int i; id1 = get_aux_id(kbdc); if (set_mouse_sampling_rate(kbdc, 10) != 10) return FALSE; /* * The device is now in the native mode? It returns a different * ID value... */ id2 = get_aux_id(kbdc); if ((id1 == id2) || (id2 != 2)) return FALSE; if (set_mouse_resolution(kbdc, PSMD_RES_LOW) != PSMD_RES_LOW) return FALSE; #if PSM_DEBUG >= 2 /* at this point, resolution is LOW, sampling rate is 10/sec */ if (get_mouse_status(kbdc, status, 0, 3) < 3) return FALSE; #endif /* * The special sequence to enable the third and fourth buttons. * Otherwise they behave like the first and second buttons. */ for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i) { if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i]) return FALSE; } /* * At this point, the device is using default resolution and * sampling rate for the native mode. */ if (get_mouse_status(kbdc, status, 0, 3) < 3) return FALSE; if ((status[1] == PSMD_RES_LOW) || (status[2] == rate[i - 1])) return FALSE; /* the device appears be enabled by this sequence, diable it for now */ disable_aux_dev(kbdc); empty_aux_buffer(kbdc, 5); return TRUE; } /* Logitech MouseMan+/FirstMouse+, IBM ScrollPoint Mouse */ static int enable_mmanplus(struct psm_softc *sc) { KBDC kbdc = sc->kbdc; int data[3]; /* the special sequence to enable the fourth button and the roller. */ /* * NOTE: for ScrollPoint to respond correctly, the SET_RESOLUTION * must be called exactly three times since the last RESET command * before this sequence. XXX */ if (!set_mouse_scaling(kbdc, 1)) return FALSE; if (!mouse_ext_command(kbdc, 0x39) || !mouse_ext_command(kbdc, 0xdb)) return FALSE; if (get_mouse_status(kbdc, data, 1, 3) < 3) return FALSE; /* * PS2++ protocl, packet type 0 * * b7 b6 b5 b4 b3 b2 b1 b0 * byte 1: * 1 p3 p2 1 * * * * byte 2: 1 1 p1 p0 m1 m0 1 0 * byte 3: m7 m6 m5 m4 m3 m2 m1 m0 * * p3-p0: packet type: 0 * m7-m0: model ID: MouseMan+:0x50, FirstMouse+:0x51, ScrollPoint:0x58... */ /* check constant bits */ if ((data[0] & MOUSE_PS2PLUS_SYNCMASK) != MOUSE_PS2PLUS_SYNC) return FALSE; if ((data[1] & 0xc3) != 0xc2) return FALSE; /* check d3-d0 in byte 2 */ if (!MOUSE_PS2PLUS_CHECKBITS(data)) return FALSE; /* check p3-p0 */ if (MOUSE_PS2PLUS_PACKET_TYPE(data) != 0) return FALSE; sc->hw.hwid &= 0x00ff; sc->hw.hwid |= data[2] << 8; /* save model ID */ /* * MouseMan+ (or FirstMouse+) is now in its native mode, in which * the wheel and the fourth button events are encoded in the * special data packet. The mouse may be put in the IntelliMouse mode * if it is initialized by the IntelliMouse's method. */ return TRUE; } /* MS IntelliMouse Explorer */ static int enable_msexplorer(struct psm_softc *sc) { static unsigned char rate0[] = { 200, 100, 80, }; static unsigned char rate1[] = { 200, 200, 80, }; KBDC kbdc = sc->kbdc; int id; int i; /* the special sequence to enable the extra buttons and the roller. */ for (i = 0; i < sizeof(rate1)/sizeof(rate1[0]); ++i) { if (set_mouse_sampling_rate(kbdc, rate1[i]) != rate1[i]) return FALSE; } /* the device will give the genuine ID only after the above sequence */ id = get_aux_id(kbdc); if (id != PSM_EXPLORER_ID) return FALSE; sc->hw.hwid = id; sc->hw.buttons = 5; /* IntelliMouse Explorer XXX */ /* * XXX: this is a kludge to fool some KVM switch products * which think they are clever enough to know the 4-byte IntelliMouse * protocol, and assume any other protocols use 3-byte packets. * They don't convey 4-byte data packets from the IntelliMouse Explorer * correctly to the host computer because of this! * The following sequence is actually IntelliMouse's "wake up" * sequence; it will make the KVM think the mouse is IntelliMouse * when it is in fact IntelliMouse Explorer. */ for (i = 0; i < sizeof(rate0)/sizeof(rate0[0]); ++i) { if (set_mouse_sampling_rate(kbdc, rate0[i]) != rate0[i]) break; } id = get_aux_id(kbdc); return TRUE; } /* MS IntelliMouse */ static int enable_msintelli(struct psm_softc *sc) { /* * Logitech MouseMan+ and FirstMouse+ will also respond to this * probe routine and act like IntelliMouse. */ static unsigned char rate[] = { 200, 100, 80, }; KBDC kbdc = sc->kbdc; int id; int i; /* the special sequence to enable the third button and the roller. */ for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i) { if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i]) return FALSE; } /* the device will give the genuine ID only after the above sequence */ id = get_aux_id(kbdc); if (id != PSM_INTELLI_ID) return FALSE; sc->hw.hwid = id; sc->hw.buttons = 3; return TRUE; } /* A4 Tech 4D Mouse */ static int enable_4dmouse(struct psm_softc *sc) { /* * Newer wheel mice from A4 Tech may use the 4D+ protocol. */ static unsigned char rate[] = { 200, 100, 80, 60, 40, 20 }; KBDC kbdc = sc->kbdc; int id; int i; for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i) { if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i]) return FALSE; } id = get_aux_id(kbdc); /* * WinEasy 4D, 4 Way Scroll 4D: 6 * Cable-Free 4D: 8 (4DPLUS) * WinBest 4D+, 4 Way Scroll 4D+: 8 (4DPLUS) */ if (id != PSM_4DMOUSE_ID) return FALSE; sc->hw.hwid = id; sc->hw.buttons = 3; /* XXX some 4D mice have 4? */ return TRUE; } /* A4 Tech 4D+ Mouse */ static int enable_4dplus(struct psm_softc *sc) { /* * Newer wheel mice from A4 Tech seem to use this protocol. * Older models are recognized as either 4D Mouse or IntelliMouse. */ KBDC kbdc = sc->kbdc; int id; /* * enable_4dmouse() already issued the following ID sequence... static unsigned char rate[] = { 200, 100, 80, 60, 40, 20 }; int i; for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i) { if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i]) return FALSE; } */ id = get_aux_id(kbdc); if (id != PSM_4DPLUS_ID) return FALSE; sc->hw.hwid = id; sc->hw.buttons = 4; /* XXX */ return TRUE; } /* Interlink electronics VersaPad */ static int enable_versapad(struct psm_softc *sc) { KBDC kbdc = sc->kbdc; int data[3]; set_mouse_resolution(kbdc, PSMD_RES_MEDIUM_HIGH); /* set res. 2 */ set_mouse_sampling_rate(kbdc, 100); /* set rate 100 */ set_mouse_scaling(kbdc, 1); /* set scale 1:1 */ set_mouse_scaling(kbdc, 1); /* set scale 1:1 */ set_mouse_scaling(kbdc, 1); /* set scale 1:1 */ set_mouse_scaling(kbdc, 1); /* set scale 1:1 */ if (get_mouse_status(kbdc, data, 0, 3) < 3) /* get status */ return FALSE; if (data[2] != 0xa || data[1] != 0 ) /* rate == 0xa && res. == 0 */ return FALSE; set_mouse_scaling(kbdc, 1); /* set scale 1:1 */ sc->config |= PSM_CONFIG_HOOKRESUME | PSM_CONFIG_INITAFTERSUSPEND; return TRUE; /* PS/2 absolute mode */ } static int psmresume(device_t dev) { struct psm_softc *sc = device_get_softc(dev); int unit = device_get_unit(dev); int err = 0; int s; int c; if (verbose >= 2) log(LOG_NOTICE, "psm%d: system resume hook called.\n", unit); if (!(sc->config & PSM_CONFIG_HOOKRESUME)) return (0); /* don't let anybody mess with the aux device */ if (!kbdc_lock(sc->kbdc, TRUE)) return (EIO); s = spltty(); /* block our watchdog timer */ sc->watchdog = FALSE; untimeout(psmtimeout, (void *)(uintptr_t)unit, sc->callout); callout_handle_init(&sc->callout); /* save the current controller command byte */ empty_both_buffers(sc->kbdc, 10); c = get_controller_command_byte(sc->kbdc); if (verbose >= 2) log(LOG_DEBUG, "psm%d: current command byte: %04x (psmresume).\n", unit, c); /* enable the aux port but disable the aux interrupt and the keyboard */ if ((c == -1) || !set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT | KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { /* CONTROLLER ERROR */ splx(s); kbdc_lock(sc->kbdc, FALSE); log(LOG_ERR, "psm%d: unable to set the command byte (psmresume).\n", unit); return (EIO); } /* flush any data */ if (sc->state & PSM_VALID) { disable_aux_dev(sc->kbdc); /* this may fail; but never mind... */ empty_aux_buffer(sc->kbdc, 10); } sc->inputbytes = 0; /* try to detect the aux device; are you still there? */ if (sc->config & PSM_CONFIG_INITAFTERSUSPEND) { if (reinitialize(unit, &sc->mode)) { /* yes */ sc->state |= PSM_VALID; } else { /* the device has gone! */ restore_controller(sc->kbdc, c); sc->state &= ~PSM_VALID; log(LOG_ERR, "psm%d: the aux device has gone! (psmresume).\n", unit); err = ENXIO; } } splx(s); /* restore the driver state */ if ((sc->state & PSM_OPEN) && (err == 0)) { /* enable the aux device and the port again */ err = doopen(unit, c); if (err != 0) log(LOG_ERR, "psm%d: failed to enable the device (psmresume).\n", unit); } else { /* restore the keyboard port and disable the aux port */ if (!set_controller_command_byte(sc->kbdc, kbdc_get_device_mask(sc->kbdc), (c & KBD_KBD_CONTROL_BITS) | KBD_DISABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) { /* CONTROLLER ERROR */ log(LOG_ERR, "psm%d: failed to disable the aux port (psmresume).\n", unit); err = EIO; } } /* done */ kbdc_lock(sc->kbdc, FALSE); if ((sc->state & PSM_ASLP) && !(sc->state & PSM_VALID)) { /* * Release the blocked process; it must be notified that the device * cannot be accessed anymore. */ sc->state &= ~PSM_ASLP; wakeup((caddr_t)sc); } if (verbose >= 2) log(LOG_DEBUG, "psm%d: system resume hook exiting.\n", unit); return (err); } DRIVER_MODULE(psm, atkbdc, psm_driver, psm_devclass, 0, 0); /* * This sucks up assignments from PNPBIOS and ACPI. */ #define PSMCPNP_DRIVER_NAME "psmcpnp" static devclass_t psmcpnp_devclass; static device_probe_t psmcpnp_probe; static device_attach_t psmcpnp_attach; static device_method_t psmcpnp_methods[] = { DEVMETHOD(device_probe, psmcpnp_probe), DEVMETHOD(device_attach, psmcpnp_attach), { 0, 0 } }; static driver_t psmcpnp_driver = { PSMCPNP_DRIVER_NAME, psmcpnp_methods, 1, /* no softc */ }; static struct isa_pnp_id psmcpnp_ids[] = { { 0x130fd041, "PS/2 mouse port" }, /* PNP0F13 */ { 0x1303d041, "PS/2 port" }, /* PNP0313, XXX */ { 0 } }; static int create_a_copy(device_t atkbdc, device_t me) { device_t psm; u_long irq; irq = bus_get_resource_start(me, SYS_RES_IRQ, 0); if (irq <= 0) return ENXIO; /* shouldn't happen */ psm = BUS_ADD_CHILD(atkbdc, 1, "psm", 0); if (psm == NULL) return ENXIO; /* move our resource to the new copy */ bus_set_resource(psm, SYS_RES_IRQ, KBDC_RID_AUX, irq, 1); bus_delete_resource(me, SYS_RES_IRQ, 0); /* ...then probe and attach it */ return device_probe_and_attach(psm); } static int psmcpnp_probe(device_t dev) { device_t atkbdc; if (ISA_PNP_PROBE(device_get_parent(dev), dev, psmcpnp_ids)) return ENXIO; /* * If we find an atkbdc device on the same bus, * create our copy there. */ atkbdc = device_find_child(device_get_parent(dev), ATKBDC_DRIVER_NAME, device_get_unit(dev)); if (atkbdc == NULL) return ENXIO; if (device_get_state(atkbdc) == DS_ATTACHED) create_a_copy(atkbdc, dev); /* keep quiet */ if (!bootverbose) device_quiet(dev); return 0; } static int psmcpnp_attach(device_t dev) { return 0; } DRIVER_MODULE(psmcpnp, isa, psmcpnp_driver, psmcpnp_devclass, 0, 0); DRIVER_MODULE(psmcpnp, acpi, psmcpnp_driver, psmcpnp_devclass, 0, 0);