ttwwakeup(). The conditions for doing the wakeup will soon become
more complicated and I don't want them duplicated in all drivers.
It's probably not worth making ttwwakeup() a macro or an inline
function. The cost of the function call is relatively small when
there is a process to wake up. There is usually a process to wake
up for large writes and the system call overhead dwarfs the function
call overhead for small writes.
Temporarily nuke TS_WOPEN. It was only used for the obscure MDMBUF
flow control option in the kernel and for informational purposes
in `pstat -t'. The latter worked properly only for ptys. In
general there may be multiple processes sleeping in open() and
multiple processes that successfully opened the tty by opening it
in O_NONBLOCK mode or during a window when CLOCAL was set. tty.c
doesn't have enough information to maintain the flag but always
cleared it in ttyopen().
TS_WOPEN should be restored someday just so that `pstat -t' can
display it (MDMBUF is already fixed). Fixing it requires counting
of processes sleeping in open() in too many serial drivers.
Temporarily nuke TS_WOPEN. It was only used for the obscure MDMBUF
flow control option in the kernel and for informational purposes
in `pstat -t'. The latter worked properly only for ptys. In
general there may be multiple processes sleeping in open() and
multiple processes that successfully opened the tty by opening it
in O_NONBLOCK mode or during a window when CLOCAL was set. tty.c
doesn't have enough information to maintain the flag but always
cleared it in ttyopen().
TS_WOPEN should be restored someday just so that `pstat -t' can
display it (MDMBUF is already fixed). Fixing it requires counting
of processes sleeping in open() in too many serial drivers.
Don't put partial PARMRK escape sequences in the input queue. Use
MAX_INPUT = TTYHOG instead of TTYHOG directly for the maximum input
queue size. Don't use the bogus MAX_INPUT advertised in
<sys/syslimits.h>.
First of many changes required to restore lost stability to the tty
driver.
ECHONL is supposed to enable echoing of NL when ECHO is off, but it
enabled echoing of everything except NL.
VBLK vnodes isn't adequate since all NFS nodes aren't locked, either. The
result is a race condition that would lead to duplicate buffers at the
same block offset.
Submitted by: John Dyson
This is performed by using a line similar to:
controller scbus0 at ahc0 bus 1
to wire scbus0 to the second bus on an adaptec 2742T controller.
Reviewed by: Peter Dufault(dufault@hda.com), Rod Grimes(rgrimes@FreeBSD.org)
buses on multi-bus controllers. Currently only affects the 274xT controllers.
Reviewed by: Peter Dufault(dufault@hda.com), Rod Grimes(rgrimes@FreeBSD.org)
emul code when compiling with "options KTRACE".
ktrsyscall() was expecting an array of integers, this was passing the
address of a structure containing an array of integers..
The cosmetic problem was that it was calling the "enter syscall"
trace hook twice - this looks like a cut/paste error/typo.
Submitted by: Andrew McRae <andrew@mega.com.au>
Some initial commits from the pcmcia stuff, to make life easier for the
testers.
We will use the name "pccard" since that is really the buzzword at present.
notebooks where a powerfail condition (external power drop; battery
state low) is signalled by an NMI. Makes it beep instead of panicing.
Reviewed by: davidg
associated files.
Submitted by: leo@dachau.marco.de (Matthias Pfaller)
Not-obtained from: NetBSD. Instead sent directly to me by Matthias.
(Sorry, this is to prevent people from claiming i might have gotten
this from NetBSD. :)
probes). Apart from there being no reason to set SCSI_NOSLEEP on every
tape command, this prevents controller drivers from sleeping when resources
are fully utilized causing unecessary "Oops not queued" errors. This is
only noticed for controllers that can run out of resources like the
27/2842 adaptec controllers. Before this fix, it is almost impossible to
perform extended tape operations if more than one scsi disk is on the
bus with the tape drive with these controllers. This does not address a
similar problem that could occur if devices are probed while other targets
are active since SCSI_NOSLEEP will still be set in that case.
made a change to NFS that caused buffers at EOF to be variable size. This
had the undesired side-effect of breaking delayed writes on NFS. This
fixes it.
Submitted by: John Dyson
the problem "when a file is truncated on the server after being written on
a client under NFSv3, the client doesn't see the size drop to zero".
(As you noted, the problem is that NMODIFIED wasn't being cleared by nfs_close
when it flushed the buffers. After checking through the code, the only place
where NMODIFIED was used to test for the possibility of dirty blocks was in
nfs_setattr(). The two cases are safe to do when there aren't dirty blocks,
so I just took out the tests. Unfortunately, testing for
v_dirtyblkhd.lh_first being non-null is not sufficient, since there are
times when the code moves blocks to the clean list and then back to the
dirty list.)
Submitted by: rick@snowhite.cis.uoguelph.ca
Future Domain TMC-885 controllers. These beasts were just different enough in
a number of perverse ways to be recognised but not work with the seagate
stuff. I also whacked in blind transfers for DATAIN and DATAOUT phases - this
more than doubles my throughput. If you're dubious about that, comment out the
definition of SEA_BLINDTRANSFER. Anyway if you're running an ST01 or TMC-950
controller, please give this a go, I'd like to see if anything's broken for
those beasts.
Submitted by: Stephen Hocking <sysseh@devetir.qld.gov.au>
what CSRG had, plus make things like, TYPE, REVISION, and BRANCH
easy to set, and derive RELEASE and VERSION from them.
Kill the JUST_TELL_ME hack, it is no longer needed.
Kill DISTNAME, I could find no reveference to it any place in the
source tree.
Now I just need to rework a few bits in release/Makefile, but want
to wait and talk to jkh about that.
Oh, and your now all running:
TYPE="FreeBSD"
REVISION="2.2"
BRANCH="CURRENT"
and the -BUILD-yymmdd is dead and gone. The date was already in the
version[] string, no need for it to be there in 2 formats!
NOTE: libkvm, w, ps, 'top', and any other utility which depends on struct
proc or any VM system structure will have to be rebuilt!!!
Much needed overhaul of the VM system. Included in this first round of
changes:
1) Improved pager interfaces: init, alloc, dealloc, getpages, putpages,
haspage, and sync operations are supported. The haspage interface now
provides information about clusterability. All pager routines now take
struct vm_object's instead of "pagers".
2) Improved data structures. In the previous paradigm, there is constant
confusion caused by pagers being both a data structure ("allocate a
pager") and a collection of routines. The idea of a pager structure has
escentially been eliminated. Objects now have types, and this type is
used to index the appropriate pager. In most cases, items in the pager
structure were duplicated in the object data structure and thus were
unnecessary. In the few cases that remained, a un_pager structure union
was created in the object to contain these items.
3) Because of the cleanup of #1 & #2, a lot of unnecessary layering can now
be removed. For instance, vm_object_enter(), vm_object_lookup(),
vm_object_remove(), and the associated object hash list were some of the
things that were removed.
4) simple_lock's removed. Discussion with several people reveals that the
SMP locking primitives used in the VM system aren't likely the mechanism
that we'll be adopting. Even if it were, the locking that was in the code
was very inadequate and would have to be mostly re-done anyway. The
locking in a uni-processor kernel was a no-op but went a long way toward
making the code difficult to read and debug.
5) Places that attempted to kludge-up the fact that we don't have kernel
thread support have been fixed to reflect the reality that we are really
dealing with processes, not threads. The VM system didn't have complete
thread support, so the comments and mis-named routines were just wrong.
We now use tsleep and wakeup directly in the lock routines, for instance.
6) Where appropriate, the pagers have been improved, especially in the
pager_alloc routines. Most of the pager_allocs have been rewritten and
are now faster and easier to maintain.
7) The pagedaemon pageout clustering algorithm has been rewritten and
now tries harder to output an even number of pages before and after
the requested page. This is sort of the reverse of the ideal pagein
algorithm and should provide better overall performance.
8) Unnecessary (incorrect) casts to caddr_t in calls to tsleep & wakeup
have been removed. Some other unnecessary casts have also been removed.
9) Some almost useless debugging code removed.
10) Terminology of shadow objects vs. backing objects straightened out.
The fact that the vm_object data structure escentially had this
backwards really confused things. The use of "shadow" and "backing
object" throughout the code is now internally consistent and correct
in the Mach terminology.
11) Several minor bug fixes, including one in the vm daemon that caused
0 RSS objects to not get purged as intended.
12) A "default pager" has now been created which cleans up the transition
of objects to the "swap" type. The previous checks throughout the code
for swp->pg_data != NULL were really ugly. This change also provides
the rudiments for future backing of "anonymous" memory by something
other than the swap pager (via the vnode pager, for example), and it
allows the decision about which of these pagers to use to be made
dynamically (although will need some additional decision code to do
this, of course).
13) (dyson) MAP_COPY has been deprecated and the corresponding "copy
object" code has been removed. MAP_COPY was undocumented and non-
standard. It was furthermore broken in several ways which caused its
behavior to degrade to MAP_PRIVATE. Binaries that use MAP_COPY will
continue to work correctly, but via the slightly different semantics
of MAP_PRIVATE.
14) (dyson) Sharing maps have been removed. It's marginal usefulness in a
threads design can be worked around in other ways. Both #12 and #13
were done to simplify the code and improve readability and maintain-
ability. (As were most all of these changes)
TODO:
1) Rewrite most of the vnode pager to use VOP_GETPAGES/PUTPAGES. Doing
this will reduce the vnode pager to a mere fraction of its current size.
2) Rewrite vm_fault and the swap/vnode pagers to use the clustering
information provided by the new haspage pager interface. This will
substantially reduce the overhead by eliminating a large number of
VOP_BMAP() calls. The VOP_BMAP() filesystem interface should be
improved to provide both a "behind" and "ahead" indication of
contiguousness.
3) Implement the extended features of pager_haspage in swap_pager_haspage().
It currently just says 0 pages ahead/behind.
4) Re-implement the swap device (swstrategy) in a more elegant way, perhaps
via a much more general mechanism that could also be used for disk
striping of regular filesystems.
5) Do something to improve the architecture of vm_object_collapse(). The
fact that it makes calls into the swap pager and knows too much about
how the swap pager operates really bothers me. It also doesn't allow
for collapsing of non-swap pager objects ("unnamed" objects backed by
other pagers).
proc or any VM system structure will have to be rebuilt!!!
Much needed overhaul of the VM system. Included in this first round of
changes:
1) Improved pager interfaces: init, alloc, dealloc, getpages, putpages,
haspage, and sync operations are supported. The haspage interface now
provides information about clusterability. All pager routines now take
struct vm_object's instead of "pagers".
2) Improved data structures. In the previous paradigm, there is constant
confusion caused by pagers being both a data structure ("allocate a
pager") and a collection of routines. The idea of a pager structure has
escentially been eliminated. Objects now have types, and this type is
used to index the appropriate pager. In most cases, items in the pager
structure were duplicated in the object data structure and thus were
unnecessary. In the few cases that remained, a un_pager structure union
was created in the object to contain these items.
3) Because of the cleanup of #1 & #2, a lot of unnecessary layering can now
be removed. For instance, vm_object_enter(), vm_object_lookup(),
vm_object_remove(), and the associated object hash list were some of the
things that were removed.
4) simple_lock's removed. Discussion with several people reveals that the
SMP locking primitives used in the VM system aren't likely the mechanism
that we'll be adopting. Even if it were, the locking that was in the code
was very inadequate and would have to be mostly re-done anyway. The
locking in a uni-processor kernel was a no-op but went a long way toward
making the code difficult to read and debug.
5) Places that attempted to kludge-up the fact that we don't have kernel
thread support have been fixed to reflect the reality that we are really
dealing with processes, not threads. The VM system didn't have complete
thread support, so the comments and mis-named routines were just wrong.
We now use tsleep and wakeup directly in the lock routines, for instance.
6) Where appropriate, the pagers have been improved, especially in the
pager_alloc routines. Most of the pager_allocs have been rewritten and
are now faster and easier to maintain.
7) The pagedaemon pageout clustering algorithm has been rewritten and
now tries harder to output an even number of pages before and after
the requested page. This is sort of the reverse of the ideal pagein
algorithm and should provide better overall performance.
8) Unnecessary (incorrect) casts to caddr_t in calls to tsleep & wakeup
have been removed. Some other unnecessary casts have also been removed.
9) Some almost useless debugging code removed.
10) Terminology of shadow objects vs. backing objects straightened out.
The fact that the vm_object data structure escentially had this
backwards really confused things. The use of "shadow" and "backing
object" throughout the code is now internally consistent and correct
in the Mach terminology.
11) Several minor bug fixes, including one in the vm daemon that caused
0 RSS objects to not get purged as intended.
12) A "default pager" has now been created which cleans up the transition
of objects to the "swap" type. The previous checks throughout the code
for swp->pg_data != NULL were really ugly. This change also provides
the rudiments for future backing of "anonymous" memory by something
other than the swap pager (via the vnode pager, for example), and it
allows the decision about which of these pagers to use to be made
dynamically (although will need some additional decision code to do
this, of course).
13) (dyson) MAP_COPY has been deprecated and the corresponding "copy
object" code has been removed. MAP_COPY was undocumented and non-
standard. It was furthermore broken in several ways which caused its
behavior to degrade to MAP_PRIVATE. Binaries that use MAP_COPY will
continue to work correctly, but via the slightly different semantics
of MAP_PRIVATE.
14) (dyson) Sharing maps have been removed. It's marginal usefulness in a
threads design can be worked around in other ways. Both #12 and #13
were done to simplify the code and improve readability and maintain-
ability. (As were most all of these changes)
TODO:
1) Rewrite most of the vnode pager to use VOP_GETPAGES/PUTPAGES. Doing
this will reduce the vnode pager to a mere fraction of its current size.
2) Rewrite vm_fault and the swap/vnode pagers to use the clustering
information provided by the new haspage pager interface. This will
substantially reduce the overhead by eliminating a large number of
VOP_BMAP() calls. The VOP_BMAP() filesystem interface should be
improved to provide both a "behind" and "ahead" indication of
contiguousness.
3) Implement the extended features of pager_haspage in swap_pager_haspage().
It currently just says 0 pages ahead/behind.
4) Re-implement the swap device (swstrategy) in a more elegant way, perhaps
via a much more general mechanism that could also be used for disk
striping of regular filesystems.
5) Do something to improve the architecture of vm_object_collapse(). The
fact that it makes calls into the swap pager and knows too much about
how the swap pager operates really bothers me. It also doesn't allow
for collapsing of non-swap pager objects ("unnamed" objects backed by
other pagers).
(on an i486, 10 cycles (+ cache misses) instead of 15). The
change should be a no-op if the compiler is any good. The best
possible i*86 code for the same algorithm is only 1 more cycle
faster on i486's so I don't want to bother implementing an
assembler version.
scanc() is a bottleneck for OPOST processing. It is naturally
about 4 times as slow as bcopy() on 32-bit systems.
were two races:
- q_to_b() might unexpectedly return 0 (e.g, after a keyboard signal
flushes the output queue and isn't echoed). ansi_put() interprets
0 bytes as 4GB...
- more output (e.g. for echoes) might arrive afer q_to_b() returns 0.
Then scstart() returns presumably and the new output might not be
handled for a long time.
Remove unused function scxint().
Fix prototypes (foo() isn't a prototype).
syscons' output is now only about 4-5 times slower than I want.
It loses a factor of 2 for scrolling output by unnecessarily copying
the screen buffer, a factor of 4/3 for dumb OPOST processing, and
a factor of 3/2 for clist processing.
Adds support for non-Sound Blaster host adapters, including those
distributed by Reveal, Lasermate, IBM, Media Vision, Crystal and others.
The driver automatically senses the correct adapter type and you can
have both in the system at the same time.
(This change should eliminate a few complaints.)
Corrected bit-masking problem that prevented use on SB Vibra-16 boards.
Declared some internal data and functions static that should have been
that way all along.
Documentation changes reflect the new hardware support and change the
appearance version to 2.0.5 (was 2.1). Nice and tidy. :-)
Beta testers have verified functionality on SB16, Vibra-16, Media Vision
and Reveal adapters. -Wall still shows no warnings.
Frank Durda IV
uhclem%nemesis@fw.ast.com
Submitted by: Frank Durda IV <uhclem%nemesis@fw.ast.com>
or ssthresh that we were able to use
tcp_var.h - declare tcpstat entries for above; declare tcp_{send,recv}space
in_rmx.c - fill in the MTU and pipe sizes with the defaults TCP would have
used anyway in the absence of values here
>Synopsis: Booting w/scsi tape in drive causes first use to fail
Booting with a tape in a SCSI tape drive will cause the first
use of the tape to fail with the following message:
st0: bad request, must be between 0 and 0.
Submitted by: mpp@legarto.minn.net (Mike Pritchard)
that call vnode_pager_alloc() so that a failure return can be dealt with.
This fixes a panic seen on NFS clients when a file being opened is deleted
on the server before the open completes.
syscall to allow applications linked against their libc's uname() to
work. Netscape 1.1N being a prime example, which prints:
"uname() failed. cant tell what system we're running on".
This change is a little ugly, but that's mainly because of the "interesting"
semantics of the BSDI extension.
Since ogetkerninfo() is only enabled by COMPAT_43, Netscape will only
be affected on kernels with that option (eg: "GENERIC")
Reviewed by: davidg
Kernel PPP doesn't pay attention to IPTOS_LOWDELAY, but uses
a table of port numbers, which isn't a generic method. The following
patch fixes this (the table is still used, but in addition
PPP queues the packet in fastq if IPTOS_LOWDELAY is set.
Obtained from: Tatu Ylonen <ylo@cs.hut.fi>
Submitted by: Heikki Suonsivu <hsu@clinet.fi>
might not be handled by the same FS as the directory (e.g. special device
files)...so it must be special-cased. This bug is seen when doing
"ln /dev/console /dev/foo" or equivilent and first appeared after I fixed
the argument order of VOP_LINK. YUCK! There really needs to be a way of
specifying what vp to use in the VCALL; doing this could fix the strategy
and bwrite special-cases, too.
- use pseudo-dma
- provide the same features and interface as sio
- support multiple boards
- fix bugs.
Some compile-time configuration constants are set to support higher
speeds and Cyclom-16Y's at a 30% relative cost in efficiency.
Cyclom-16Y support is untested.
form to do this than it is relying on individual subroutines (the logic
in epioctl is itself very minimal). Ideally, unnecessary splimp()'s should
now be removed if they exist; I'll leave this for a later date (a complete
code review of the driver needs to be done). Fixes a bug I noticed that
would show up when ifconfig'ing the interface down.
optimizations I have been working on yet, but does bring in some bug fixes
and performance improvments that were easy to regression test:
Setup the data fifo threshold and bus off timing correctly for 27/284x cards.
Users of these adapters with fast periferals (greater than 5MB/s) will notice
a big performance difference. (Sometimes as large as going from 3.7->8.3MB/s).
Fix handling of the active target flags. Some of the outbs where missing
the base offset in the abort code. The abort code still needs lots of work.
Support 3940 controllers, but only with 16 SCBs for now. Eventually I'll
add support for all 255, but I need to find a tester for the code first since
we have to enable the cards external SRAM to do this.
Add Dan Eischen's serial eeprom reading facilities. This allows the 2940
adapters to pull additional information left over from SCSI-Select right out
out of the configuration seeprom.
If the BIOS is disabled on 274x controllers, reset all target parameters
to there defaults since you can't rely on what is stored in scratch ram.
Report motherboard controllers as such.
Stick the first SG address and count into the SCB data and count areas for
all transfers in preparation of a later sequencer optimization.
Keep track of which targets can are allowed to have the disconnection
priveledge since this will be handled by the kernel driver in the future.
If a target issues a message reject in response to a tagged message,
disable tagged queuing for that target. Some seagates say they can do
tagged queuing, but lie, and its a shame to have to disable tagged queuing
on all devices just because you have one that can't cope.
is needed for 3940 support.
Have tagged commands look to see if a target is "busy" with a non tagged
command before executing. This prevents overlapped tagged and non tagged
commands which can happen since request sense commands are not tagged.
incorrect indents, a variety of poor coding practices such as comparing
pointers to constants ('0'), poor code structuring, etc, etc. This brings
the code up to the minimum standards for inclusion in FreeBSD.
2) Rewrote "bad_packet" code to be less buggy and more readable.
3) Removed a pile of goto's; the code is now somewhat less reminiscent
of a certain Italian pasta.
4) Changed all boolean returns of "0" and "1" to FALSE/TRUE.
assigning an address to an interface automatically marks this
interface IFF_UP. The fix corrects this (and closes PR sys/577).
This is consistent with the way ethernet interfaces are being handled.
know better when to cache values in the route, rather than relying on a
heuristic involving sequence numbers that broke when tcp_sendspace
was increased to 16k.
series of hard disk drives, which don't accept any SCSI message
within an REQUEST SENSE command (i.e. even not an IDENTIFY to set
the LUN).
This patch obviates the need for QUIRK_NOMSG and thus all of the
device_tab[] entries in the NCR driver.
people tend to assume their devices won't work if they see this
message, though it may indicate that those devices just don't
need any PCI driver (e.g. devices that emulate an ISA card, or
that have been initialised by the BIOS and need no further care).
fail on new hardware (Compaq Prolinea and Compaq Prosignea), and that
doesn't erroneously identify old mech. 2 chip sets as using mech. 1.
(See section 3.6.4.1.1 of the PCI bus specs rev. 2.0)
2) Removed unnecessary vm_object_lookup()/pager_cache(object, TRUE) pairs
after vnode_pager_alloc() calls - the object is already guaranteed to be
persistent.
3) Removed some gratuitous casts.
should be completely ignored for point-to-point interfaces).
For point-to-point interfaces, route based on the destination address,
not the local address.
Submitted by: Peter Wemm
a related bug in some of the new 'foo'boot bootstrap code that has been
added over the past months. This change makes it no longer necessary
for the bootstrap to fix up the path (i.e. it can be removed).
include/signal.h:
There was massive namespace pollution from including <sys/types.h>.
POSIX functions were declared even when _ANSI_SOURCE is defined.
sys.sys/signal.h:
NSIG was declared even if _ANSI_SOURCE or _POSIX_SOURCE is defined.
sig_atomic_t wasn't declared if _POSIX_SOURCE is defined.
Declare a typedef for signal handling functions and use it to
unobfuscate declarations and to avoid half-baked function types
that cause unwanted compiler warnings at certain warning levels.
Fix confusing comment about SA_RESTART.
sys/i386/include/signal.h:
This has to be included to get the declaration of sig_atomic_t even
when _ANSI_SOURCE is defined, so be more careful about polluting
the ANSI namespace.
Uniformize idempotency ifdefs.
of the typedefs off_t and pid_t when use of the latter would cause
namespace pollution. These macros are used like _BSD_VA_LIST_ and
aren't #undef'ed when the corresponding typedef is declared.
off_t is very machine-dependent and should never have been decided
in <sys/types.h> (its declaration is compiler-dependent). pid_t
isn't very machine-dependent, but this might change. `long' is
a wasteful type for it if longs are longer than ints.
Move the definition of _BSD_VA_LIST_ away from the comment that
suggests that it is #undefed when va_list is declared.
VOP_CLOSE() takes `F' (file) flags, not `IO' flags. At least that's
what close() passes. I previously fixed ttylclose() to check
FNONBLOCK instead of IO_NDELAY. This broke the call from vclean()
and cleaning of ptys sometimes deadlocked.
The version 2 support has been tested (client+server) against FreeBSD-2.0,
IRIX 5.3 and FreeBSD-current (using a loopback mount). The version 2 support
is stable AFAIK.
The version 3 support has been tested with a loopback mount and minimally
against an IRIX 5.3 server. It needs more testing and may have problems.
I have patched amd to support the new variable length filehandles although
it will still only use version 2 of the protocol.
Before booting a kernel with these changes, nfs clients will need to at least
build and install /usr/sbin/mount_nfs. Servers will need to build and
install /usr/sbin/mountd.
NFS diskless support is untested.
Obtained from: Rick Macklem <rick@snowhite.cis.uoguelph.ca>
on dlclose. Also correctly call constructors and destructors for libraries
linked with /usr/lib/c++rt0.o.
Change interpretation of dlopen manpage to call _init() rather than init()
for dlopened objects.
Change c++rt0.o to avoid using atexit to call destructors, allowing dlclose to
call destructors when an object is unloaded.
Change interface between crt0 and ld.so to allow crt0 to call a function on
exit to call destructors for shared libraries explicitly.
These changes are backwards compatible. Old binaries will work with the new
ld.so and new binaries will work with the old ld.so. A version number has
been introduced in the crt0-ld.so interface to allow for future changes.
Reviewed by: GAWollman, Craig Struble <cstruble@singularity.bevc.blacksburg.va.us>
forwarding between networks that aren't directly connected) not to work
by intercepting the wrong protocol number. This should fix a bug reported
previously by someone I don't remember.
when syscons stops mapping the console to minor MAXCONS. There is
usually no corresponding device in /dev, and the correct device has
minor 0.
cons.c:
Initialize cn_tty properly, so that CPU_CONSDEV can work.
Comment about too many variants of the console tty pointer.
machdep.c:
Return device NODEV and not error EFAULT when there is no console device.
clearer. The "informational message" almost looks like an instruction to
the user to change settings on the card....
It's cosmetic, but...
Submitted by: peter@haywire.dialix.com
This first shot only incorporaties so much functionality that DOOM
can run (the X version), signal handling is VERY weak, so is many
other things. But it meets my milestone number one (you guessed it
- running DOOM).
Uses /compat/linux as prefix for loading shared libs, so it won't
conflict with our own libs.
Kernel must be compiled with "options COMPAT_LINUX" for this to work.
user has entered a bogus kernel name in the first place).
Also fix the broken #ifdef FORCE_COMCONSOLE, it has been disabled by
accident. (NB: the keyboard probe remains disabled however.)
Few cosmetic fixes (declare functions to be void instead of int),
while i've been at this.
Pointed out by: wosch@cs.tu-berlin.de (Wolfram Schneider), for the init bug
explicitly advise the users to reset the machine in case they have
done bogus things (to prevent `dset' from merging the changes into
/kernel), and it's also useful for machines with serial consoles that
are physically in another place.
no ports are active, provided there are no polled ports and no
`LOSESOUTINTS' ports. Do a little more in the interrupt handler instead.
This is a little less efficient if there are are many active ports but
a little more efficient otherwise. Polled ports are ones with no irq
specified (as before). `LOSESOUTINTS' ports are ones with 0x08 set in
their config flags. Unless this flag is set, it will now take up to one
second to recover from lost output interrupts, if any. Some 8250s and
16450s lose output interrupts.
Improve output buffering: copy the clist buffer to 2 linear buffers if
necessary and possible instead of to 1. Handle an arbitrary queue of
buffers in the interrupt handler. Check for waking up sleepers after
copying characters out of the clist buffer instead of before.
Delay translation of TIOCM_DTR to MCR_DTR etc. so that the top level
routines are more machine independent.
Fix bogus device register in unused code.
SLIP device.
2) Don't directly frob the IFF_UP flag - use if_up/if_down as it was
intended.
3) Return ENETDOWN if IFF_UP isn't set when outputing, drop the packet if
if IFF_UP isn't set when inputing.
its connection parameters, we want to keep statistics on how often this
actually happens to see whether there is any work that needs to be done in
TCP itself.
Suggested by: John Wroclawski <jtw@lcs.mit.edu>
For the LKM_E_LOAD case of the DISPATCH() macro, use lkmexists() to
make sure we don't have another instance the module we're trying to
load already loaded _before_ calling the module's load() function.
If lkmexists() returns true, return EEXIST without trying to load
the module.
For most types of modules, the individual dispatch functions in the
kernel check for duplicated modules, but for LM_MISC we can't trust
the module to do the checks itself. Currently, the kernel does
do an lkmexists() check on LM_MISC modules, but not until after
the module's load() function has been called, which is too late
for it to do any good. If the load() function does irreversible
things to the kernel, the belated lkmexists() check forces an
unload() and a crash.
in the wrong place. Blank padding in the right place or zero padding
would be inconsistent with user mode.
Put case 'p' in alphabetical order.
Implement %p in sprintf() too. I'd like only a single, more complete
printf() core, perhaps one based on vsnprintf().
Fix one such THING in code to match comment.
Sort IO_GSC* into numeric order and update comments about the gaps.
Sort common SCSI addresses into alphabetical order.
Remove bogus comments about com ports having i/o size 4.
Uniformize whitespace.
Uniformize case in hex digits.
This file is very incomplete. In particular, it doesn't mention any
network cards. This doesn't matter much for the base addresses, but
it means that the comments about which addresses are free are mostly
bogus. The i/o sizes are unreliable because of split address ranges
for many devices (VGA, wd). The i/o sizes are incomplete. In
particular, there are no sizes for SCSI controllers. The bt driver
still returns a truth value instead of a size.
is an ambiguity in the NFS version 2 protocol.
VREG should be taken literally as a regular file. If a
server intents to return some type information differently
in the upper bits of the mode field (e.g. for sockets, or
FIFOs), NFSv2 mandates fa_type to be VNON. Anyway, we
leave the examination of the mode bits even in the VREG
case to avoid breakage for bogus servers, but we make sure
that there are actually type bits set in the upper part of
fa_mode (and failing that, trust the va_type field).
NFSv3 cleared the issue, and requires fa_mode to not
contain any type information (while also introduing sockets
and FIFOs for fa_type).
The fix has been tested against a variety of NFS servers.
It fixes problems with the ``Tropic'' NFS server for Windows,
while apparently not breaking anything.
Pointed-out by: scott@zorch.sf-bay.org (Scott Hazen Mueller)
- the major number wasn't checked, so accesses beyond the end of bdevsw[]
were possible. Bogus major numbers are easy to get because `sysctl -w'
doesn't handle dev_t's reasonably - it doesn't convert names to dev_t's
and it converts the number 1025 to the dev_t 0x35323031.
- Driver d_psize() functions return -1 to indicate error ENXIO or ENODEV
(the interface is too braindamaged to say which). -1 was interpreted
as a size and resulted in the bogus error ENOSPC.
- it was possible to set the dumpdev for devices without a d_psize()
function. This is equivalent to setting the dumpdev to NODEV except
it confuses sysctl.
- change a 512 to DEV_BSIZE. There is an official macro dtoc() for
converting "pages" to disk blocks but it is never used in /usr/src/sys.
There is much confusion between PAGE_SIZE sized pages and NBPG sized
pages. Maxmem consists of both.
Not fixed:
- there is nothing to invalidate the dumpdev if the media goes away.
This reduces the benefits of the early calculation of dumplo. Bounds
checking in the dump routines is relied on to reduce the risk of
damage and little would be lost by relying on the dump routines to
calculate dumplo.
- no attempt is made to stay away from the start of the device to
avoid clobbering labels.
Fix wrong && anachronistic comment about the type of bootdev.
Reviewed by: davidg
Submitted by: Bruce Evans
handled correctly. This would manifest itself as "object deallocated too
many times" panics and perhaps other strange inconsistencies on NFS servers.
Reviewed by: me, of course
Submitted by: John Dyson
LINT talks about about 2.1. I changed that to 2.0.5,
and clarified why certain devices need "at scbus?".
There is still a crazy "PCVT=210" which shouldn't be there,
but corrected comment as it is needed for 2.0.5.
for broadcasts if point-to-point links shared the same IP address as
the ethernet. The fix must be enabled with P2P_LOCALADDR_SHARE option
in the kernel config file. This will someday likely be standard, but
there isn't sufficient time before release to determine if there are
any interoperability problems with routed and/or gated.
Reviewed by: Garrett Wollman, and me
Submitted by: Peter Wemm
- option DODUMP no longer exists (remove all references to it).
- directive `swap on' is now a no-op (don't bother documenting it; remove
comment to match code).
- directive `dumps on' still works (restore code to match comment; deprecate
it in comment).
Reviewed by: Poul-Henning Kamp, and me
Submitted by: Bruce Evans
etc.). The tulip_start routine was rewritten to use less stack space (I've
been having problems with wcarchive overflowing the stack and this should
help a little). This version also has preliminary NetBSD support.
Rod Grimes helped in testing this version of the driver. Thanks Rod. It's
additionally been extensively tested here and on wcarchive.
Submitted by: Matt Thomas
in machdep.c (it should use the global nmbclusters). Moved the calculation
of nmbclusters into conf/param.c (same place where nmbclusters has always
been assigned), and made the calculation include an extra amount based
on "maxusers". NMBCLUSTERS can still be overrided in the kernel config
file as always, but this change will make that generally unnecessary. This
fixes the "bug" reports from people who have misconfigured kernels seeing
the network hang when the mbuf cluster pool runs out.
Reviewed by: John Dyson
in machdep.c (it should use the global nmbclusters). Moved the calculation
of nmbclusters into conf/param.c (same place where nmbclusters has always
been assigned), and made the calculation include an extra amount based
on "maxusers". NMBCLUSTERS can still be overrided in the kernel config
file as always, but this change will make that generally unnecessary. This
fixes the "bug" reports from people who have misconfigured kernels seeing
the network "hang" when the mbuf cluster pool runs out.
Reviewed by: John Dyson
regular user could panic the machine with a simple "tail /proc/curproc/mem"
command. The problem was twofold: both kernfs and procfs didn't fill in
the mnt_stat statfs struct (which would later lead to an integer divide
fault in the vnode pager), and kernfs bogusly paniced if a bmap was
attempted.
Reviewed by: John Dyson
device.
v_numoutput wasn't incremented to match the b_iodone nesting. It's still
fishy that vwakeup() clears B_WRITEINPROG before biodone() has finished;
however, B_WRITEINPROG seems to be never used.
Submitted by: Bruce Evans
the National Semiconductor InfoMover PCMCIA cards also. In tests on a
NE4100 on Jordan's laptop here, the ze driver works fine with that
card.
Reviewed by: Jordan Hubbard, Rod Grimes, and me
Submitted by: Gary Palmer
to most users (the wrong length is passed to ether_input). The
second is more serious. The multicast hash algorithm uses the wrong
(low) bits instead of the right (high) bits. This is only an issue
if you use >12 multicast addresses but if you are using IP multicast
then it might affect you...
Submitted by: Matt Thomas
thrown out if bpfilter support and no BPF listener. (submitted by Bill
Fenner)
Removed unused variable and changed another from a stack variable to a
static - the variable was a rather large array of structs that consumed
a lot of stack space. (me)
1) Files weren't properly synced on filesystems other than UFS. In some
cases, this lead to lost data. Most likely would be noticed on NFS.
The fix is to make the VM page sync/object_clean general rather than
in each filesystem.
2) Mixing regular and mmaped file I/O on NFS was very broken. It caused
chunks of files to end up as zeroes rather than the intended contents.
The fix was to fix several race conditions and to kludge up the
"b_dirtyoff" and "b_dirtyend" that NFS relies upon - paying attention
to page modifications that occurred via the mmapping.
Reviewed by: David Greenman
Submitted by: John Dyson
These changes solve the problem in a general way by moving the
initialization out of the individual fs_mountroot's and into swaponvp().
Submitted by: Poul-Henning Kamp
changes. The check for nswap was bogus, but the code was so convoluted
that it was difficult to tell. It's better now. :-)
Reviewed by: David Greenman (extensively), and John Dyson
Submitted by: Poul-Henning Kamp, w/tweaks by me.
inconsistencies in the VM system that eventually lead to a panic. These
changes fix the behavior to conform to the behavior in SunOS, which is
to deny faults to pages beyond the EOF (returning SIGBUS). Internally,
this is implemented by requiring faults to be within the object size
boundaries. These changes exposed another bug, namely that passing in
an offset to mmap when trying to map an unnamed anonymous region also
results in internal inconsistencies. In this case, the offset is forced
to zero.
Reviewed by: John Dyson and others
serial_putchar() always hung if it was called and the serial port existed,
so booting with -h hung when the above bug was fixed. Previously, setting
-h did nothing but -h was sometimes the default due to the stack garbage
bug.
Submitted by: DI. Christian Gusenbauer <cg@scotty.edvz.uni-linz.ac.at>
The `howto' arg to boot() was not supplied, so it was stack garbage (actually
the return address in the boot program). I didn't use the submitted fix.
1) If a target initiated a sync negotiation with us and happened to chose a
value above 15, the old code inadvertantly truncated it with an "& 0x0f".
If the periferal picked something really bad like 0x32, you'd end up with
an offset of 2 which would hang the drive since it didn't expect to ever
get something so low. We now do a MIN(maxoffset, given_offset).
2) In the case of Wide cards, we were turning on sync transfers after a
sucessfull wide negotiation. Now we leave the offset alone in the per
target scratch space (which implies asyncronous transfers since we initialize
it that way) until a syncronous negotation occurs.
3) We were advertizing a max offset of 15 instead of 8 for wide devices.
4) If the upper level SCSI code sent down a "SCSI_RESET", it would hang the
system because we would end up sending a null command to the sequencer. Now
we handle SCSI_RESET correctly by having the sequencer interrupt us when it
is about to fill the message buffer so that we can fill it in ourselves.
The sequencer will also "simulate" a command complete for these "message only"
SCBs so that the kernel driver can finish up properly. The cdplay utility
will send a "SCSI_REST" to the cdplayer if you use the reset command.
5) The code that handles SCSIINTs was broken in that if more than one type
of error was true at once, we'd do outbs without the card being paused.
The else clause after the busfree case was also an accident waiting to
happen. I've now turned this into an if, else if, else type of thing, since
in most cases when we handle one type of error, it should be okay to ignore
the rest (ie if we have a SELTO, who cares if there was a parity error on
the transaction?), but the section should really be rewritten after 2.0.5.
This fix was the least obtrusive way to patch the problem.
6) Only tag either SDTR or WDTR negotiation on an SCB. The real problem is
that I don't account for the case when an SCB that is tagged to do a particular
type of negotiation completes or SELTOs (selection timeout) without the
negotiation taking place, so the accounting of sdtrpending and wdtrpending
gets screwed up. In the wide case, if we tag it to do both wdtr and sdtr,
it only performs wdtr (since wdtr must occur first and we spread out the
negotiation over two commands) so we always have sdtrpending set for that
target and we never do a real SDTR. I fill properly fix the accounting
after 2.0.5 goes out the door, but this works (as confirmed by Dan) on
wide targets.
Other stuff that is also included:
1) Don't do a bzero when recycling SCBs. The only thing that must explicitly
be set to zero is the scb control byte which is done in ahc_get_scb. We also
need to set the SG_list_pointer and SG_list_count to 0 for commands that do
not transfer data.
2) Mask the interrupt type printout for the aic7870 case. The bit we were
using to determine interrupt type is only valid for the aic7770.
Submitted by: Justin Gibbs
IGMPv2 spec. This fixes the following bugs:
o ntohs() on a char provides silly results
o timer needs to be scaled to units of PR_FASTHZ; this was being done
inconsistenly so now it gets done when it is initialized.
Reviewed by: Garrett Wollman
Submitted by: Bill Fenner <fenner@parc.xerox.com>
Bruce Evans
David Greenman
Paul Traina
Peter Wemm
Justin T. Gibbs
Garrett Wollman
Poul-Henning Kamp
Joerg Wunsch
Doug Rabson
Jordan K. Hubbard
Rodney W. Grimes
Andreas Schulz
Stefan Eßer
Andrey A. Chernov
Gary Palmer
Guido van Rooij
Søren Schmidt
Atsushi Murai
Bill Paul