floppy drive #0, regardless of what the CMOS says. This is intended
as a bandaid for those plagued with Compaq's idea to not announce the
floppy drive on their `Aero' notebook.
Using the device flags is not very nice (in particular since they
aren't per-drive but per-controller), but still looks a lot better to
me than the disgusting guesswork hack that was recently posted to
-hackers.
Doc update will follow shortly.
Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
internal modems. Currently detects a USR modem, and a couple Supra
modems... vendor id's for sio capabile cards welcomed...
document new option EXTRA_SIO that will increase sio's internal data
structures to support X more serial ports... these are used by the
PnP part of sio for attaching... If you don't have it specified, it
will default to 2... This is defaulted to 0 if you don't have PnP
compiled into your kernel...
also document that if you set the PnP flags (pnp x flags y) to 0x1 that
the modem will be refused to be recognized by the sio driver... this
is for people that want the traditional isa driver to probe and attach
the modem... (for keeping legacy sio numbering)
number of dma overruns/underruns for systems under heavy dma load.
As a side effect, broken enhanced floppy controllers that sometimes
don't detect dma overruns/underruns will give less errors.
Reviewed by: j@uriah.heep.sax.de (J Wunsch)
Hide the bogus FDC ``chip type'' display behind a (mostly) undocumented
option, since people started to trust the bogus claim. Once we're going
to handle 2.88 MB controllers, we have to redo the chip detection, by
now just leave it hidden.
size in terms of lines (instead of bytes). When changing video mode
in ioctl SW_XXX commands, syscons checks scp->history_size and
allocate a history buffer at least as large as the new screen size.
(This was unnecessary before, because HISTORY_SIZE was as large as 100
lines and this is bigger than the maximum screen size: 60 lines).
Similar adjustment is done in ioctl CONS_HISTORY command too.
PR: kern/4169
Reviewed by: sos
and hardware.
There is now another simple_lock around clock data/hardware accesses in
clock.c and microtime.s. It is my belief that this is the only area
sio/cy might stumble into during an unblocked INTerrupt. Thus I separated
the sio/cy code from the generic disable_intr()/enable_intr() routines.
Controlled by smptests.h: USE_COMLOCK, ON by default.
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
Made NEW_STRATEGY default.
Removed misc. old cruft.
Centralized simple locks into mp_machdep.c
Centralized simple lock macros into param.h
More cleanup in the direction of making splxx()/cpl MP-safe.
Several new fine-grained locks.
New FAST_INTR() methods:
- separate simplelock for FAST_INTR, no more giant lock.
- FAST_INTR()s no longer checks ipending on way out of ISR.
sio made MP-safe (I hope).
Add support for MODEX 320x240x256color with "unchained" adressing, giving
access to all 256K on all VGA's, those with that much memory that is :)
Also make sysmouse use the right resolution in graphics modes.
- removed TEST_ALTTIMER.
- removed APIC_PIN0_TIMER.
- removed TIMER_ALL.
apic_vector.s:
- new algorithm where a CPU uses try_mplock instead of get_mplock:
if successful continue as before.
if fail set ipending bit, mask INT (to avoid recursion), cleanup & iret.
This allows the CPU to return to successful work, while the ISR will be run
by the CPU holding the lock as part of the doreti dance.
1. Add new interface, add_scrn_saver()/remove_scrn_saver(), to declare
loading/unloading of a screen saver. The screen saver calls these
functions to notify syscons of loading/unloading events.
It was possible to load multiple savers each of which will try to
remember the previous saver in a local variable (`old_saver'). The
scheme breaks easily if the user load two savers and unload them in a
wrong order; if the first saver is unloaded first, `old_saver' in the
second saver points to nowhere.
Now only one screen saver is allowed in memory at a time.
Soeren will be looking into this issue again later. syscons is
becoming too heavy. It's time to cut things down, rather than adding
more...
2. Make scrn_timer() to be the primary caller of the screen saver
(*current_saver)(). scintr(), scioctl() and ansi_put() update
`scrn_time_stamp' to indicate that they want to stop the screen saver.
There are three exceptions, however.
One is remove_scrn_saver() which need to stop the current screen saver
if it is running. To guard against scrn_timer() calling the saver during
this operation, `current_saver' is set to `none_saver' early.
The others are sccngetc() and sccncheckc(); they will unblank the
screen too. When the kernel enters DDB (via the hot key or a
break point), the screen saver will be stopped by sccngetc().
However, we have a reentrancy problem here. If the system has been in
the middle of the screen saver...
(The screen saver reentrancy problem has always been with sccnputc()
and sccngetc() in the -current source. So, the new code is doing no
worse, I reckon.)
3. Use `mono_time' rather than `time'.
4. Make set_border() work for EGA and CGA in addition to VGA. Do
nothing for MDA.
Changes to the LKM screen saver modules will follow shortly. YOU NEED
TO RECOMPILE BOTH SCREEN SAVERS AND KERNEL AS OF THESE CHANGES.
Reviewed by: sos and bde
and released. It should use `spcl' consistently in both cases,
otherwise shift/control/alt state may not be correctly set/reset.
(Even with this fix, you can still make syscons confused and fail to
change internal state if you really want to, by installing a really
arcane and artificial keymap.)
PR: i386/4030
Reviewed by: sos
cursor (CHAR_CURSOR)
1. Reduced the number of calls to set_destructive_cursor(). The
destructive cursor produced noticeable overhead on the system. It was
caused by draw_cursor_image() calling set_destructive_cursor() every
so often.
set_destructive_cursor() absolutely needs to be called when
a) the character code under the cursor has changed either because
the cursor moved or because the screen was updated or the mouse
pointer overlapped the cursor.
b) Or a new font has been loaded,
c) or the video mode has been changed,
d) or the cursor shape has been changed,
e) or the user switched virtual consoles.
2. Turn off the configuration flag CHAR_CURSOR (destructive cursor) in
scattach() if we have a non-VGA card. The destructive cursor works
only for VGA.
3. Removed redundant calls to set_destructive_cursor() in some places.
4. Fixed the "disappearing mouse pointer" problem. The mouse pointer
looked hidden under the destructive cursor when it overlaped the cursor.
A slightly different version of the patch was reviewd and OKed by
sos and ache.
Add a new configuration flag, KBD_NORESET (0x20) to tell scprobe() not
to reset the keyboard.
IBM ThinkPad 535 has the `Fn' key with which the user can perform
certain functions in conjunction with other keys. For example, `Fn' +
PageUP/PageDOWN adjust speaker volume, `Fn' + Home/End change
brightness of LCD screen. It can also be used to suspend the system.
It appears that these functions are implemented at the keyboard level
or the keyboard controller level and totally independent from BIOS or
OS. But, if the keyboard is reset (as is done in scprobe()), they
become unavailable. (There are other laptops which have similar
functions associated with the `Fn' key. But, they aren't affected by
keyboard reset.)
ThinkPad 535 doesn't have switches or buttons to adjust brightness and
volume, or to put the system into the suspend mode. Therefore, it is
essential to preserve these `Fn' key functions in FreeBSD. The new
flag make scprobe() skip keyboard reset.
If this flag is not set, scprobe() behaves in the same say as before.
(If we only knew a way to detect ThinkPad 535, we could skip keyboard
reset automatically, but...)
adapter during the system boot. It always assumes there is at least a
monochrome adapter.
This is rather strange assumption. If there is no dispaly adapter, the
console driver cannot be any good...
In this patch, scinit() is split into two parts; the first part is
now called scvidprobe() which will detect the presence of video card
at the CGA or MONO buffer address and returns TRUE if found. It is
called during sccnprobe() and scprobe(). Both will fail if no video
card is found.
The second part, whose name stays the same as before, scinit(), is
called from sccninit() and scattach() to complete initialization of
the found video card.
The keyboard probe code is moved from scprobe() to sckbdprobe();
scprobe() now calls scvidprobe() and sckbdprobe() to carry out device
probe. (This is rather a cosmetic change, but it sure makes the code
look better organized.)
The problem pointed out by Joerg.
Joerg Wunsch
Poul-Henning Kamp
Jordan K. Hubbard
Søren Schmidt
Jun-ichiro itojun Hagino
Justin T. Gibbs
John-Mark Gurney
Tor Egge
Peter Wemm
Kazutaka YOKOTA
Steve Passe
Bruce Evans
Mike Smith
John Dyson
Brian Somers
Andrey A. Chernov