PDRSHIFT.
The SYSTEM constant that was defined in this file has been replaced
with KERNBASE from param.h.
Changed almost all # style comments to /* */ C style comments. Several
comments cleaned up so that they make a little more since.
In the comments that describe C calling conventions to assembler routines
used a comma space sequence to seperate arguments and removed the space
between the function name and the argument list.
Removed useless comments like /* clr eax */.
Changed all comma space sequences on assemble instructions to just be comma.
Removed spaces after $ operators to make the file consistent, this may need
to change again (ie: $KERNBASE should probably be $(KERNBASE), but for now
it all seems to work just fine.) This may become a problem with the C
pre-processor.
Changed several double blank lines to single blank lines that where used
to seperate the I/O routines, these routines are blocked enough that we
don't need double blank lines between them.
Changed sequence of I/O routines to be all input functions, all output
functions instead of just the opposite.
Moved the SHOW_A_LOT debug stuff to near the end of the file.
Changed two occurances of the constant 0xfff to NBPG-1.
the proper I_X86CPU in the config file the following error will occur
while building the kernel: (had to line wrap the error for this message)
../../i386/i386/machdep.c:343: #error This kernel is not configured for one \
of the supported CPUs
Remove patch kit headers, and add $Id$
This is mostly to align some more code with NetBSD.
cpu.h:
Remove the old function vs. include configuration stuff that was
ifdefed out when we went to inline functions.
Remove the define of resettodr that made it a nop, there is
already a function that makes it a nop, no need to #define one.
Remove the #defines of processor types, they are now defined
in cputypes.h, #include that file.
Add struct cpu_nameclass for support of cpu types.
frame.h:
include sys/signal.h, it will be needed in the future.
put the sigframe structure here that was in machdep.c
pcb.h:
Add multiple inclusion protection.
Add pcb_ldt and pcb_ldt_len to pcb structure, this is for the
user mode ldt.
removed patch kit headers and sccsids, add $Id$. This is a general
clean up and reallignment with NetBSD-current where possible.
genassym.c:
removed extranious include of reg.h
removed old FP_* defines that have been ifdefed out since the patch kit
removed PCB_SIGC that is not referenced anywhere
add trapframe and sigframe defines
add KERNBASE define for use in locore.s
locore.s:
include npx.h and use NNPX for turning on and off FPU
include machine/cputypes.h for the types of cpu (used in cpu_identify)
change SYSPDREND to be one higher, this is really the base of the
next area, and will be changing again next time I revise the file
Reverse the NOP defines, you now get slow NOP's by default, this
may be what is casuing us trouble with some systems. If you want
the NOPS to be null you now need to have options DUMMY_NOPS.
Now get esym from the boot blocks which don't pass it yet, and
it is not used, but this will be changing.
Move the bit_colors stuff to be in with the rest of Bruces SHOW_A_LOT
things for debugging.
Added NetBSD's CPU type probe code, we now know what type of CPU
we are running on.
Adjust kernel pde calcuation to correct for change in SYSPDREND, no
longer need the +1.
machdep.c
include npx.h and use NNPX for turning on and off FPU
include isa.h, map.h(new file), exec.h in preperation for
changes that are still in process.
Add some of the code for MACHINE_NONCONTIG that will alow us
to better map around the BIOS memory area.
Now print the version, cpu id, real memory and availiable memory
during boot.
Correct the calculation of bufpages, the code was mixing pages
and bytes, it now does the right things. Removed Bill's hack
for limiting the erronous calculation.
add the identifycpu print out code from NetBSD.
remove the definition of the sigframe struct, it belongs in
frame.h
put in printf's about syncing disks on a halt/reboot.
Change the halted message to be a little easier reading.
Clean up of the dump messages, makes the source and the output
much more readable.
Change 0,0 in several places to have spaces after the commas.
it relocates it to be after the BIOS memory hole instead of right below
the 640K limit.
THANK YOU CHRIS!!!
From: <cgd@postgres.Berkeley.EDU>
Date: Wed, 29 Sep 93 18:49:58 -0700
basically, reserve a new 32k space right after firstaddr,
and put the buffer space there...
the diffs are below, and are in ~cgd/sys/i386/i386 (in machdep.c)
on freefall. i obviously can't test them, so if some of you would
look the diffs over and try them out...
Date: Sun, 12 Sep 1993 18:19:05 -0500
This will allow you to compile and run a freebsd kernel with shared
memory support. I haven't tested the shm*() calls yet.
You run out of page table descriptors if you specify 4Mb of sharable
memory (SHMMAXPGS=1024). I don't know what the limit is, but
SHMMAXPGS=64 works. Rich
going to panic shortly after this anyway. Destroys less state, and
keeps the machine from waiting for someone to smash the return key
a few times before it panics!
Added support of DONET({IMP,NS,ISO}) so you can now compile with options
NS and ISO, still missing some IMP code, but since the imp is old and
gone I doubt this will ever be used.
FP and we try to call the emulator when it is not compiled in.
Removed the #if defined(i486) || defined(i387) that use to call the
panic if we did not have a math emulator.
Removed an extranious include of i386/i386/math_emu.h from math_emulate.c.
I posted some patches on the 386bsd_patchkit list to prohibit io access.
Because of a noninitialised filed in the tss, this was possible.
It is included below as the patch to machdep.c
However, when you do this *necessary* fix (security), it will be
impossible form within user space to do io.
therefor, I included another fix: when you open /dev/io, you
get the access. Of course you can rewrite it to use another minor
and thus giving access to the iospace when /dev/mem is opened, e.g.
NOTE: The /dev/io entry has not been added to /dev/MAKEDEV yet.
The patch is in NetBSD.
profiling, and various protection checks that cause security holes
and system crashes.
* Changed min/max/bcmp/ffs/strlen to be static inline functions
- included from cpufunc.h in via systm.h. This change
improves performance in many parts of the kernel - up to 5% in the
networking layer alone. Note that this requires systm.h to be included
in any file that uses these functions otherwise it won't be able to
find them during the load.
* Fixed incorrect call to splx() in if_is.c
* Fixed bogus variable assignment to splx() in if_ed.c
argument definitions outside of the function parameter list. This is
to reduce the copious warning messages that (non-Jolitz) gcc produces.
Also fixed some bogus variable declarations and casts to make the
compiler happy.
way of doing things. There still remain several drivers that need to
be updated. Also added a compile-time option to pccons to switch the
control and caps-lock keys (REVERSE_CAPS_CTRL) - added for my personal
sanity.
Rodney W. Grimes
David Greenman
Nate Williams
Andrew Moore
Paul Richards
Charlie Root