a BIOS was not installed, this will still be true by the time we probe
the chip. We use this heuristic to determine if we should use the left
over scratch ram target settings for controllers that don't have an
SEEPROM. We also "snapshot" the host adapter SCSI id and whether ultra
is enabled or not and use these values if a BIOS was installed. The card
will act as if a BIOS was installed even if there wasn't one if you warm
reboot, but since the scratch ram area is still valid in this case, its
hardly worth the effort of writing a shutdown routing that clears out
the scratch ram. This should make users of motherboard controllers
happy.
should be <= than subordinate, not the other way around.
They are both true if the bridge is not cascaded (i.e., twin-channel
scsi/e-net adapters won't be affected by this bug), which is probably why
it was unnoticed until today.
- always use pci_conf_read() and pci_conf_write(). (This is required to
simulate non-existant devices in my system for PCI bridge code tests.)
- reorder some functions (put the main functions at the end).
- correct off by one bug in the code dealing with unitialized PCI to PCI
bridge chips. (Bug found by ASAMI Satoshi.)
- print function number for multi-function devices.
Use new XS_SELTIMEOUT error code for selection timeouts.
aic7870.c:
Move SCB walking code to aic7xxx.c and make it work for all card types.
The flag AHC_EXTSCB is no longer needed since the SCBs are walked in
all cases now.
vm_offset_t is currently unsigned long but should probably be plain
unsigned for i386's to match the choice of minimal types to represent
for fixed-width types in Lite2. Anyway, it shouldn't be assumed
to be unsigned long.
I only fixed the type mismatches that were detected when I changed
vm_offset_t to unsigned. Only pointer type mismatches were detected.
- Do not enable tagged commands by default
- Probe only 1 LUN
- Do not negotiate sync. transfer with CDROM drives
Defining FAILSAFE will result in a driver that will tolerate
marginal hardware for the price of a slight loss of performance
It is intended for use in install kernels.
Cleanse the SCSI subsystem of its internally defined types
u_int32, u_int16, u_int8, int32, int16, int8.
Use the system defined *_t types instead.
aic7870.c:
Handle Seeprom data a little better.
the S-Video input. It also has code in the driver for the meteor RGB support
and some other bug fixes. I don't have a meteor RGB but I have been told
that it works.
Submitted by: Jim Lowe <james@miller.cs.uwm.edu>
port addresses (even though the PC architecture doesn't support them).
Add code to limit the I/O map size based on the lowest set bit of the
address. This cures the problem with the BT946C only having a 16 bit
map register, in voiolation of the PCI specs, without giving up the
general support of >65K port regions.
- fill in and use ifp->if_softc
- use if_bpf rather than private cookie variables
- change bpf interface to take advantage of this
- call ether_ifattach() directly from Ethernet drivers
- delete kludge in if_attach() that did this indirectly
that don't announce support for command queues.
SCSI_NCR_DFLT_TAGS can be specified in the kernel config file
and sets the default number of tags per disk drive.
A value of 0 means "no tags".
Minor correction in debug messages: Values from the msg_in
buffer were being printed in the msg_out trace message ...
feature in the header type register, though it is required by the PCI spec.
This should correctly probe both functions of the Intel 82371FB chip,
without the need for a special case based on the device ID.
chipset. This does not attempt to do anything special with the timing
on the hope that the BIOS will have done the right thing already. The
actual interface from the wd driver to the new facility is not
implemented yet (this commit being an attempt at prodding someone else
to do it because looking at the wd driver always confuses the h*** out of me).
includes a hack in the probe code: the 82371FB is a multifuction
device, but doesn't properly set the configuration bit which
indicates this. So, we just hard-wire all 82371FBs as multifunction
devices.
This does not actually make the bus-master IDE stuff work, although
if anyone wants to work on that, I have the databooks that tell
how to use it.
(To be replaced by sysctl accesses some time ...)
Remove a backward jump from the NCR script, which allowed a SCSI target
to receive any number of NOP messages it desired. If a target indeed
does such a silly thing, make it fail at the next instruction, instead
of causing a timeout a few seconds later.
Simplify the initialization of adapters by pulling all card specific
initialization to the card specific modules.
Set the Latency timer and Burst len to good values if thery are not
initialized during post or are reset during chip reset.
Properly identify and handle external SCB SRAM. The code was false
id'ing 255 SCBs on aic7880 chips.
Reviewed by: David Greenman <davidg@FreeBSd.org>
#includes to get prototypes.
pci now uses a different interrupt handler type for interrupts that it
dispatches and the isa interrupt handler type for the interrupts that
it handles.
Reduce default value of pcicb_membase to 0x2000000 (from 0x4000000)
since this seems to be the lower bound used by many systems.
Submitted by: Mihoko Tanaka <m_tanaka@pa.yokogawa.co.jp>
all the other bt_XXX() functions in i386/scsi/bt*.
This the important effect of forcing a link error if the user is
still using the old "vector btintr" which is dangerously wrong
after Justin's updates to the driver.
The correct isa vector line for the bt driver is "vector bt_isa_intr".
Justin mentioned this in the commit message and updated LINT and
GENERIC. This change is to enforce that.. :-)
most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
Removed ifnet.if_init and ifnet.if_reset as they are generally unused.
Change the parameter passed to if_watchdog to be a ifnet * rather than
a unit number. All of this is an attempt to move toward not needing an
array of softc pointers (which is usually static in size) to point to
the driver softc.
if_ed.c:
Changed some of the argument passing to some functions to make a little
more sense.
if_ep.c, if_vx.c:
Killed completely bogus use of if_timer. It was being set in such a way
that the interface was being reset once per second (blech!).
o Add signed/unsigned functionality to the matrox meteor device driver.
o Apply a few fixes to the sound driver.
o Add a ``SPIGOT_UNSECURE'' compile time definition so, if one defines
SPIGOT_UNSECURE in their conf file, then they can use the spigot w/o
root. There is a warning that this allows users access to the IO
page which is probably not secure.
Submitted by: james
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
incompatible with the type of a PCI interrupt handler.
Fixed the type of pdc_pci_ifintr(). The type of a PCI interrupt handler
is too generic to pass arbitrary struct pointers.
incompatible with the type of a PCI interrupt handler. A new entry
point `ahc_pci_intr()' is used for PCI. ISA and PCI interrupts are
penalized equally (:-) by calling a common handler `ahc_intr()'. This
should be reorganized. Some strings now name the wrong function...
Submitted by: fgray@rice.edu
this driver hasn't been checked but as a separate module, bringing it in won't
break anything else and it't the best way of testing it......
julian
If RAMENB is set in devconfig, walk the external SCBs. Some Intel Xpress
motherboards set this bit.
For external SCBs for the 3940. It doesn't set RAMPS or RAMENB, but does
have the ram.
"I screwed the initialization of the burstsize. Right now it will default
to 0 (which can cause corruption problems on high latency PCI buses). It
should be set to 8 longwords to avoid problems with certain PCI chipsets."
Submitted by: Matt Thomas <matt@lkg.dec.com>
Justin T. Gibbs
Poul-Henning Kamp
Satoshi Asami
Stefan Eßer
David Greenman
Bruce Evans
Jordan K. Hubbard
Marc G. Fournier
Bill Fenner
Garrett Wollman
Mike Pritchard
Andreas Schulz
Peter Wemm
Julian Elischer