anything for two mintues (see ``set choked'' and ``show
bundle''), nuke the ip, mp and link level buffer queues.
This should fix problems where ``ppp -auto'' seems to stop
responding after failing to connect to the peer a few times.
the device is successfully opened. If we fail to open it,
mention the fact.
Also go back into command mode as soon as the device is closed
rather than waiting for the user to type something before noticing.
(see the new ``set callback'' and ``set cbcp'' commands)
o Add a ``cbcp'' log level and mbuf type.
o Don't dump core when \T is given in ``set login'' or
``set hangup''.
o Allow ``*'' and blanks as placeholders in ppp.secret and
allow a fifth field for specifying auth/cbcp dialback
parameters.
o Remove a few extraneous #includes
o Define the default number of REQs (restart counter) in defs.h
rather than hardcoding ``5'' all over the place.
o Fix a few man page inconsistencies.
``add .... HISADDR''. The network will never be
reachable at this point unless we're in -auto or reading
the command from ppp.linkup.
We can now run the following lines and get the expected
results:
set ifaddr 1.2.3.4/0 5.6.7.8/0
add default HISADDR
where a route is added immediately in auto mode and the
whole thing is delayed 'till the IP numbers have been
agreed in other modes.
Essentially, ppp.linkup is no longer required.
end up writing zero bytes, sleep for 1/10 of a second so that
we don't end up using up too much cpu.
This should only ever happen on systems that wrongly report a
descriptor as writable despite the tty buffer being full.
Discussed with: Jeff Evarts
o Do an initial run-time check to see if select() alters the passed
timeval. This knowledge isn't yet used, but will be soon.
for all datalinks in a bundle. Ppp now deals correctly
with link types that are changed while open
o When changing the type of the last AUTO link, only clear
the interface if we're not in PHASE_NETWORK. This allows
us to switch to -ddial mode while we have a connection
without suddenly unexpectedly throttling ourselves by
clearing the interface configuration.
Problem area noted by: Aaron Jeremias Luz <aaron@csh.rit.edu>
*after* shuffling fragments from the IP queue into the
individual link queues.
This fixes a latency problem pointed out by: Bruce Evans <bde@zeta.org.au>
that we're now closing, manually HUP that session leader
so that the tty is fully released.
o Always restart our carrier detect timer in the receiving
process if it was running in the sending process (as we
now *always* pass the descriptor).
o Tweak argv when we go into pause() mode to keep our session
so that ps can see what's going on (without checking for a
`pause' state in `ps -l').
in `set mode', `allow modes', on the command line and when
outputting mode names. The strings are matched so that only
enough characters to uniquely identify the string are required,
so you can now
ppp -a mylabel (for auto mode)
ppp -b mylabel (for background mode)
ppp -dd mylabel (for direct dial mode)
etc.
o Make -ddial dial when specified on the command line (oops).
Pointed out by: Alex <garbanzo@hooked.net>
of supporting architectures with different device names.
o Close /dev/tunX when destroying the bundle.
o Don't forget to close the parent end of the pipe in the child
process when exec'ing a program from a chat script.
o If we close our controlling terminal, ditch the current session
with it, allowing getty(8) (or whatever) to regain control.
o After transferring our controlling terminal descriptor to another
ppp instance, we now fork a new ppp to continue where we left off,
transferring ownership of all uucp locks and the /var/run/tunX.pid
file. Meanwhile the parent closes all file descriptors, defaults
all signals and does a pause() to wait for a HUP after the
transferred descriptor is finally closed.
We don't run /bin/cat any more (again!).
Suggested by: bde
TODO: It seems clocal devices need their pause()d session leader
to be given a manual HUP, as closing the last open descriptor
doesn't do the job.
generate the data to transfer.
o Transfer uucp lock ownership for the transferred device.
o Don't assume we know the correct values of dev_is_modem and
mbits after the transfer.
transferring session rights with them. Instead, create two
`/bin/cat' processes. A new child is spawned and disassociated from
the terminal and the parent, which continues with the rest of the ppp
process. Meanwhile, the parent spawns another child, and both the
parent and child exec the `/bin/cat' commands with the appropriate
descriptors. This way, the session is owned by the parent, and the
tty is held open.
o Close LCPs that have done a TLF and are now in ST_STOPPED before
calling Down. This prevents them from trying to come back up again
after the peer has shut them down (it seems a bit strange that the
rfc says that a Down in ST_STOPPED will cause a TLS etc).
o Don't try to set the physical link name pointer when we're receiving
and renaming a datalink. The physical hasn't been created yet, and as
it happens, the garbage physical pointer happens to be the value of another
physical - so we're pointing that other physical name at ourselves.
yeuck.
o Re-arrange the order of things in main (DoLoop()). We now handle
signals only after the select and not before the UpdateSet. It's
possible that either a signal (FSM timeout) or a descriptor_Read()
brings a link down, after which we'd better tidy up any dead direct
and 1off descriptors before calling UpdateSet() again.
o Mention when we detect a PPP packet when we see one before the link
is up (then start LCP as before).
It's now dealt with by the `server' object. This simplifies
things as we only have one list of prompt descriptors and
the log_ routines check prompt::logactive to determine
whether it should be used for output.
o Include the MP socket UpdateSet() result in bundle::UpdateSet().
o Don't select on the tun device unless we're in NETWORK
phase or AUTO mode.
o Stop the idle timer when we go to DEAD phase. We may
have transferred a link and not had a chance to kill
it.
o Don't fail when trying to unlink our transferred datalink
from our descriptor lists just before the transfer.
o Add our link descriptor to the write set if we got a short
write the last time (physical::out is set).
o Log the connection source address when a connection is closed.
o Remove descriptor::next field. Descriptor lists are not required
any more.
incoming fragments when a link goes down.
o Don't use the minimum sequence numbers of links that aren't open.
o Understand sequence number wrapping when determining the minimum
sequence number.
o Add & adjust a few comments.
thresholds (in terms of queued packets for a period of time)
where -auto links will be brought up and down. By default,
all auto links come up when we reach NETWORK phase and never
go down.
o Display current autoload state in `show bundle'.
o Disable the idle timer as soon as it's called.
o Disable the idle and autoload timers when exiting (in case
we're abending).
is not possible to switch to or from dedicated or direct mode,
but all other combinations are ok (eg. -auto -> -ddial).
o Cope with the fact that commands with optional context may not
be able to obtain a link with command_ChooseLink() (if all links
have been deleted for example).
o Allow `clone'ing in non-multilink mode. We may for example want
to configure two links in unilink mode and dial them both, using
the one that comes up first. It's also possible to rename
``deflink'' by cloning it, deleting the original, then setting
the mode of the new link.
the bundle has the opportunity to go PHASE_DEAD and cleanup
the interface (if it's the last link).
o Regnerate our phys_type value when we transfer the link.
o Always clean up the interface when destroying our bundle in case
we're abending.
o Always clean up our interface when the last link is gone rather than
delaying things 'till exit time in the -direct case (the interface
is useless anyway). Do this *after* slamming down our NCPs (if
they're still around).
o Our MP server descriptor now clears the relevent device descriptor
from our descriptor [fd]sets when a datalink is on death-row (to
be transferred to another running ppp), thus avoiding the possibility
of passing a bum descriptor to select() and having ppp abend.
o Handle the MP socket descriptor functions from within the bundle
descriptor functions. Now we ensure that the MP socket descriptor
functions see the descriptor sets *after* they've been seen by our
datalinks.
o Add/fix a few more comments.
o Log FD_SET()s in LogTIMER.
o Identify the descriptor that causes an EBADF from select()
if LogTIMER is enabled (then exit).
o Call the MP server UpdateSet() function after calling
the UpdateSet() for all links - the link may enter
PHASE_TERMINATE and bring down the MP server - breaking
the imminent select().
LQM and HDLC timer diagnostics come out with the correct name.
o Don't send an LQR immediately upon reviving a datalink. Leave
it 'till the next timeout.
o Add the link name to some more LQR diagnostics.
o Break out of the main loop when a descriptor exception is seen
in select().
o Remove the evil nointr_[u]sleep() functions. Timers should be
(and are) used instead.
o Treat a read() of 0 bytes as an error that's fatal to the link
on which the read() is done. We should never read() 0 after
select() says there's something there - not unless the link
has been closed by the other side.
o Write the data seen before a HDLC header to the terminal in
`term' mode, *not* back to the modem :-/
o Initialise our transmitted file descriptor before starting any
timers.
o Only send data links that have *no* pending output data. This
means that our final ACK will be written rather than being
nuked with the datalink transmission.
for the last NCP TLF.
o Move tun reading from the main loop into the bundle descriptor
handling routines.
o Cosmetic: Add a few `const's and make some diagnostics clearer.
Brian Somers