'\"COPYRIGHT 1989 by The Board of Trustees of Leland Stanford Junior University. .Dd March 25, 1995 .Dt MROUTED 8 .Os FreeBSD 2.0 .Sh NAME .Nm mrouted .Nd IP multicast routing process .Sh SYNOPSIS .Nm mrouted .Op Fl p .Op Fl c Ar config .Op Fl d Ar debuglevel .Sh DESCRIPTION The .Nm program is an implementation of the Distance-Vector Multicast Routing Protocol (DVMRP), an earlier version of which is specified in RFC-1075. It maintains topological knowledge via a distance-vector routing protocol (like RIP, described in RFC-1058), upon which it implements a multicast datagram forwarding algorithm called Reverse Path Multicasting. .Pp .Nm forwards a multicast datagram along a shortest (reverse) path tree rooted at the subnet on which the datagram originates. The multicast delivery tree may be thought of as a broadcast delivery tree that has been pruned back so that it does not extend beyond those subnetworks that have members of the destination group. Hence, datagrams are not forwarded along those branches which have no listeners of the multicast group. The IP time-to-live of a multicast datagram can be used to limit the range of multicast datagrams. .Pp In order to support multicasting among subnets that are separated by (unicast) routers that do not support IP multicasting, .Nm includes support for .Dq tunnels , which are virtual point-to-point links between pairs of .Nm programs located anywhere in an internet. IP multicast packets are encapsulated for transmission through tunnels, so that they look like normal unicast datagrams to intervening routers and subnets. The encapsulation is added on entry to a tunnel, and stripped off on exit from a tunnel. By default, the packets are encapsulated using the IP-in-IP protocol (IP protocol number 4). Older versions of .Nm tunneled using IP source routing, which puts a heavy load on some types of routers. This version supports IP source route tunnelling only for backwards compatibility. .Pp The tunnelling mechanism allows .Nm to establish a virtual internet, for the purpose of multicasting only, which is independent of the physical internet, and which may span multiple Autonomous Systems. This capability is intended for experimental support of internet multicasting only, pending widespread support for multicast routing by the regular (unicast) routers. .Nm suffers from the well-known scaling problems of any distance-vector routing protocol, and does not (yet) support hierarchical multicast routing. .Pp .Nm handles multicast routing only; there may or may not be unicast routing software running on the same machine as .Nm mrouted . With the use of tunnels, it is not necessary for .Nm to have access to more than one physical subnet in order to perform multicast forwarding. .Pp If no .Fl d option is given, or if the debug level is specified as 0, .Nm detaches from its controlling terminal. Otherwise, it remains attached to the terminal and responsive to signals. .Pp The .Nm program accepts the following command-line options: .Bl -tag -width XXXdebuglevel .It Fl c Ar config This option specifies an alternate configuration file location as .Ar config . The default location is .Pa /etc/mrouted.conf . .It Fl d Ar debuglevel This option sets the debuging level to .Ar debuglevel . Regardless of the debug level, .Nm always writes warning and error messages to the system log demon. Non-zero debug levels have the following effects: .Bl -tag -width "level 3" .It level 1 all syslog'ed messages are also printed to stderr. .It level 2 all level 1 messages plus notifications of .Dq significant events are printed to stderr. .It level 3 all level 2 messages plus notifications of all packet arrivals and departures are printed to stderr. .El .It Fl p This option disables pruning of uninterested links in the multicast distribution tree. .El .Sh CONFIGURATION .Nm automatically configures itself to forward on all multicast-capable interfaces; i.e., interfaces that have the .Dv IFF_MULTICAST flag set (excluding the loopback), and it finds other .Nm programs directly reachable via those interfaces. To override the default configuration, or to add tunnel links to other .Nm programs, configuration commands may be placed in .Pa /etc/mrouted.conf (or an alternate location can be specified using the .Fl c option). There are four types of configuration commands: .Bd -literal phyint [disable] [metric ] [threshold ] [rate_limit ] [boundary /] tunnel [metric ] [threshold ] [srcrt] [rate_limit ] [boundary /] cache_lifetime pruning .Ed .Pp One note about the configuration commands--all the phyint and tunnel command options must be on a single line except for the boundary option which may begin on a separate line. A single phyint or tunnel command may have multiple boundary options. .Pp The phyint command can be used to disable multicast routing on the physical interface identified by local IP address , or to associate a non-default metric or threshold with the specified physical interface. The local IP address may be alternatively replaced by the interface name (e.g., le0) for the phyint command only. Phyint commands must precede tunnel commands. .Pp The tunnel command can be used to establish a tunnel link between local IP address and remote IP address , and to associate a non-default metric or threshold with that tunnel. The tunnel must be set up in the mrouted.conf files of both routers before it can be used. For backwards compatibility with older .Nm programs, the srcrt keyword specifies encapsulation using IP source routing. .Pp The cache_lifetime is a value that determines the amount of time that a cached multicast route stays in kernel before timing out. The value of this entry should lie between 300 (5 min) and 86400 (1 day). It defaults to 300. .Pp The pruning option is provided for .Nm to act as a non-pruning router. It is also possible to start .Nm in a non-pruning mode using the .Fl p flag on the command line. It is expected that a router would be configured in this manner for test purposes only. The default mode is pruning enabled. .Pp The metric is the .Dq cost associated with sending a datagram on the given interface or tunnel; it may be used to influence the choice of routes. The metric defaults to 1. Metrics should be kept as small as possible, because .Nm cannot route along paths with a sum of metrics greater than 31. .Pp The threshold is the minimum IP time-to-live required for a multicast datagram to be forwarded to the given interface or tunnel. It is used to control the scope of multicast datagrams. (The TTL of forwarded packets is only compared to the threshold, it is not decremented by the threshold. Every multicast router decrements the TTL by 1.) The default threshold is 1. .Pp In general, all .Nm mrouted programs connected to a particular subnet or tunnel should use the same metric and threshold for that subnet or tunnel. .Pp The rate_limit option allows the network administrator to specify a certain bandwidth in Kbits/second which would be allocated to multicast traffic. .Pp The boundary option allows an interface to be configured as an administrative boundary for the specified scoped address. Packets belonging to this address will not be forwarded on a scoped interface. .Pp The .Nm program will not initiate execution if it has fewer than two enabled vifs, where a vif (virtual interface) is either a physical multicast-capable interface or a tunnel. It will log a warning if all of its vifs are tunnels; such an .Nm configuration would be better replaced by more direct tunnels (i.e., eliminate the middle man). .Sh SIGNALS The .Nm program responds to the following signals: .Bl -tag -width SIGTERMx .It Dv SIGHUP restarts .Nm mrouted . The configuration file is reread every time this signal is evoked. .It Dv SIGINT terminates execution gracefully (i.e., by sending good-bye messages to all neighboring routers). .It Dv SIGTERM same as .Dv SIGINT .It Dv SIGUSR1 dumps the internal routing tables to .Pa /var/tmp/mrouted.dump . .It Dv SIGUSR2 dumps the internal cache tables to .Pa /var/tmp/mrouted.cache . .It Dv SIGQUIT dumps the internal routing tables to stderr (only if .Nm was invoked with a non-zero debug level). .El .Sh EXAMPLE The routing tables look like this: .Bd -literal Virtual Interface Table Vif Local-Address Metric Thresh Flags 0 36.2.0.8 subnet: 36.2 1 1 querier groups: 224.0.2.1 224.0.0.4 pkts in: 3456 pkts out: 2322323 1 36.11.0.1 subnet: 36.11 1 1 querier groups: 224.0.2.1 224.0.1.0 224.0.0.4 pkts in: 345 pkts out: 3456 2 36.2.0.8 tunnel: 36.8.0.77 3 1 peers: 36.8.0.77 (2.2) boundaries: 239.0.1 : 239.1.2 pkts in: 34545433 pkts out: 234342 3 36.2.0.8 tunnel: 36.6.8.23 3 16 Multicast Routing Table (1136 entries) Origin-Subnet From-Gateway Metric In-Vif Out-Vifs 36.2 1 0 1* 2 3* 36.8 36.8.0.77 4 2 0* 1* 3* 36.11 1 1 0* 2 3* . . . .Ed .Pp In this example, there are four vifs connecting to two subnets and two tunnels. The vif 3 tunnel is not in use (no peer address). The vif 0 and vif 1 subnets have some groups present; tunnels never have any groups. This instance of .Nm is the one responsible for sending periodic group membership queries on the vif 0 and vif 1 subnets, as indicated by the .Dq querier flags. The list of boundaries indicate the scoped addresses on that interface. A count of the number of incoming and outgoing packets is also shown at each interface. .Pp Associated with each subnet from which a multicast datagram can originate is the address of the previous hop router (unless the subnet is directly connected), the metric of the path back to the origin, the incoming vif for multicasts from that origin, and a list of outgoing vifs. .Dq Li \&* means that the outgoing vif is connected to a leaf of the broadcast tree rooted at the origin, and a multicast datagram from that origin will be forwarded on that outgoing vif only if there are members of the destination group on that leaf. .Pp .Nm also maintains a copy of the kernel forwarding cache table. Entries are created and deleted by .Nm mrouted . .Pp The cache tables look like this: .Bd -literal Multicast Routing Cache Table (325 entries) Origin-Subnet Mcast-group CTmr IVif Prcv# Psnt Forwvifs 134.207.7 224.2.140.239 300 1 0 0 2 138.15.103 224.2.203.214 295 1 2 P 0p 2p 128.237.0 224.2.253.119 290 1 1 0 2p 129.215.200 224.2.207.48 40 1 1 0p 2 36.77.14 239.0.1.234 345 2b .Ed .Pp Each entry is characterized by the origin subnet number and the destination multicast group. The .Dq CTmr field indicates the lifetime (in seconds) of the entry. The entry is deleted from the cache table when the timer decrements to zero. The .Dq Ivif field indicates the incoming vif for multicast packets from that origin. Each router also maintains a record of the number of prunes received from neighbouring routers for a particular source and group. If there are no members of a multicast group on any downward link of the multicast tree for a subnet, a prune message is sent to the upstream router. They are indicated by a .Dq Li \&P in the .Dq Psnt field. The .Dq Forwvifs field shows the interfaces along which datagrams belonging to the source-group are forwarded. A .Dq Li \&p indicates that no datagrams are being forwarded along that interface. An unlisted interface is a leaf subnet with are no members of the particular group on that subnet. A .Dq Li \&b on an interface indicates that it is a boundary interface; i.e., traffic will not be forwarded on the scoped address on that interface. .Sh FILES .Bl -tag -compact -width /var/tmp/mrouted.cache .It Pa /etc/mrouted.conf default configuration file .It Pa /var/tmp/mrouted.cache kernel forwarding cache dump file .It Pa /var/tmp/mrouted.dump routing table dump file .El .Sh SEE ALSO .Xr map-mbone 8 , .Xr mrinfo 8 , .Xr mtrace 8 .Rs .%A "S. Deering" .%B "Proceedings of the ACM SIGCOMM '88 Conference" .%T "Multicast Routing in Internetworks and Extended LANs" .Re .Sh AUTHORS Steve Deering & Ajit Thyagarajan .Sh HISTORY The .Nm program first appeared in .Tn FreeBSD 2.0.