.\" $Id: ppp.8,v 1.19.2.8 1997/06/03 00:37:10 brian Exp $ .Dd 20 September 1995 .Os FreeBSD .Dt PPP 8 .Sh NAME .Nm ppp .Nd Point to Point Protocol (aka iijppp) .Sh SYNOPSIS .Nm .Op Fl auto | background | ddial | direct | dedicated .Op Fl alias .Op Ar system .Sh DESCRIPTION This is a user process .Em PPP software package. Normally, .Em PPP is implemented as a part of the kernel (e.g. as managed by pppd) and it's thus somewhat hard to debug and/or modify its behavior. However, in this implementation .Em PPP is done as a user process with the help of the tunnel device driver (tun). .Sh Major Features .Bl -diag .It Provides interactive user interface. Using its command mode, the user can easily enter commands to establish the connection with the remote end, check the status of connection and close the connection. All functions can also be optionally password protected for security. .It Supports both manual and automatic dialing. Interactive mode has a .Dq term command which enables you to talk to your modem directly. When your modem is connected to the remote peer and it starts to talk .Em PPP , the .Em PPP software detects it and switches to packet mode automatically. Once you have determined the proper sequence for connecting with the remote host, you can write a chat script to define the necessary dialing and login procedure for later convenience. .It Supports on-demand dialup capability. By using auto mode, .Nm will act as a daemon and wait for a packet to be sent over the .Em PPP link. When this happens, the daemon automatically dials and establishes the connection. In almost the same manner ddial mode (dedicated or daemon dialing) also automatically dials and establishes the connection. However, it differs in that it will dial the remote site any time it detects the link is down, even if there are no packets to be sent. This mode is useful for full-time connections who worry less about line charges and more about being connected full time. .It Supports packet aliasing. Packet aliasing, more commonly known as masquerading, allows computers on a private, unregistered network to access the internet. The .Em PPP host acts as a masquerading gateway. IP addresses as well as TCP and UDP port numbers are aliased for outgoing packets and de-aliased for returning packets. .It Supports background PPP connections. In background mode, if .Nm successfully establishes the connection, it will become a daemon. Otherwise, it will exit with an error. .It Supports server-side PPP connections. In direct mode, .nm acts as server which accepts incoming .Em PPP connections on stdin/stdout. .It Supports PAP and CHAP authentication. .It Supports Proxy Arp. When .Em PPP is set up as server, you can also configure it to do proxy arp for your connection. .It Supports packet filtering. User can define four kinds of filters: .Em ifilter for incoming packets, .Em ofilter for outgoing packets, .Em dfilter to define a dialing trigger packet and .Em afilter for keeping a connection alive with the trigger packet. .It Tunnel driver supports bpf. The user can use .Xr tcpdump 1 to check the packet flow over the .Em PPP link. .It Supports PPP over TCP capability. .It Supports IETF draft Predictor-1 compression. .Nm supports not only VJ-compression but also Predictor-1 compression. Normally, a modem has built-in compression (e.g. v42.bis) and the system may receive higher data rates from it as a result of such compression. While this is generally a good thing in most other situations, this higher speed data imposes a penalty on the system by increasing the number of serial interrupts the system has to process in talking to the modem and also increases latency. Unlike VJ-compression, Predictor-1 compression pre-compresses .Em all data flowing through the link, thus reducing overhead to a minimum. .It Supports Microsofts IPCP extentions. Name Server Addresses and NetBIOS Name Server Addresses can be negotiated with clients using the Microsoft .Em PPP stack (ie. Win95, WinNT) .Sh GETTING STARTED When you first run .Nm you may need to deal with some initial configuration details. First, your kernel should include a tunnel device (the default in FreeBSD 2.0.5 and later). If it doesn't, or if you require more than one tun interface, you'll need to rebuild your kernel with the following line in your kernel configuration file: .Dl pseudo-device tun N where .Ar N is the maximum number of .Em PPP connections you wish to support. Second, check your .Pa /dev directory for the tunnel device entries .Pa /dev/tunN , where .Ar N represents the number of the tun device, starting at zero. If they don't exist, you can create them by running "sh ./MAKEDEV tunN". This will create tun devices 0 through .Ar N . Last of all, create a log file. .Nm Ppp uses .Xr syslog 3 to log information. A common log file name is .Pa /var/log/ppp.log . To make output go to this file, put the following lines in the .Pa /etc/syslog.conf file: .Dl !ppp .Dl *.* /var/log/ppp.log It is possible to have more than one ppp log file by creating a link to the ppp executable: .Dl # cd /usr/sbin .Dl # ln ppp ppp0 and using .Dl !ppp0 .Dl *.* /var/log/ppp0.log in .Pa /etc/syslog.conf . Don't forget to send a .Dv HUP signal to .Nm syslogd after altering .Pa /etc/syslog.conf . .Sh MANUAL DIALING In the following examples, we assume that your machine name is .Nm awfulhak . If you set your hostname and password in .Pa /etc/ppp/ppp.secret , you can't do anything except run the help, passwd and quit commands. .Bd -literal -offset indent ppp on "your hostname"> help help : Display this message passwd : Password for security quit : Quit the PPP program ppp on awfulhak> pass .Ed The "on" part of your prompt will change to "ON" if you specify the correct password. .Bd -literal -offset indent ppp ON awfulhak> .Ed You can now specify the device name, speed and parity for your modem, and whether CTS/RTS signalling should be used (CTS/RTS is used by default). If your hardware does not provide CTS/RTS lines (as may happen when you are connected directly to certain ppp-capable terminal servers), .Nm will never send any output through the port; it waits for a signal which never comes. Thus, if you have a direct line and can't seem to make a connection, try turning ctsrts off: .Bd -literal -offset indent ppp ON awfulhak> set line /dev/cuaa0 ppp ON awfulhak> set speed 38400 ppp ON awfulhak> set parity even ppp ON awfulhak> set ctsrts on ppp ON awfulhak> show modem * Modem related information is shown here * ppp ON awfulhak> .Ed The term command can now be used to talk directly with your modem: .Bd -literal -offset indent ppp ON awfulhak> term at OK atdt123456 CONNECT login: ppp Password: Protocol: ppp .Ed When the peer starts to talk in PPP, .Nm detects this automatically and returns to command mode. .Bd -literal -offset indent ppp ON awfulhak> PPP ON awfulhak> .Ed You are now connected! Note that .Sq PPP in the prompt has changed to capital letters to indicate that you have a peer connection. The show command can be used to see how things are going: .Bd -literal -offset indent PPP ON awfulhak> show lcp * LCP related information is shown here * PPP ON awfulhak> show ipcp * IPCP related information is shown here * .Ed At this point, your machine has a host route to the peer. This means that you can only make a connection with the host on the other side of the link. If you want to add a default route entry (telling your machine to send all packets without another routing entry to the other side of the ppp link), enter the following command: .Bd -literal -offset indent PPP ON awfulhak> add 0 0 HISADDR .Ed The string .Sq HISADDR represents the IP address of the connected peer. This variable is only available once a connection has been established. A common error is to specify the above command in your .Pa ppp.conf file. This won't work as the remote IP address hasn't been established when this file is read. You can now use your network applications (ping, telnet, ftp etc.) in other windows on your machine. Refer to the PPP COMMAND LIST section for details on all available commands. .Sh AUTOMATIC DIALING To use automatic dialing, you must prepare some Dial and Login chat scripts. See the example definitions in .Pa /etc/ppp/ppp.conf.sample (the format of ppp.conf is pretty simple). .Bl -bullet -compact .It Each line contains one command, label or comment. .It A line starting with a .Sq # character is treated as a comment line. .It A label name starts in the first column and is followed by a colon (:). .It A command line must contain a space or tab in the first column. .El The .Pa ppp.conf file should consist of at least a .Dq default section. This section is always executed. It should also contain one or more sections, named according to their purpose, for example, .Dq MyISP would represent your ISP, and .Dq ppp-in would represent an incoming .Nm configuration. You can now specify the destination label name when you invoke .Nm ppp . Commands associated with the .Dq default label are executed, followed by those associated with the destination label provided. When .Nm is started with no arguments, the .Dq default section is still executed. The load command can be used to manually load a section from the .Pa ppp.conf file: .Bd -literal -offset indent PPP ON awfulhak> load MyISP .Ed Once the connection is made, the ppp portion of the prompt will change to PPP: .Bd -literal -offset indent # ppp MyISP ... ppp ON awfulhak> dial dial OK! login OK! PPP ON awfulhak> .Ed If the .Pa /etc/ppp/ppp.linkup file is available, its contents are executed when the .Em PPP connection is established. See the provided .Dq pmdemand example in .Pa /etc/ppp/ppp.conf.sample which adds a default route. The string HISADDR is available as the IP address of the remote peer. .Sh BACKGROUND DIALING If you want to establish a connection using .Nm non-interactively (such as from a .Xr crontab(5) entry or an .Xr at(1) job) you should use the .Fl background option. You must also specify the destination label in .Pa /etc/ppp/ppp.conf to use. This label must contain the .Dq set ifaddr command to define the remote peer's IP address. (refer to .Pa /etc/ppp/ppp.conf.sample ) When .Fl background is specified, .Nm attempts to establish the connection immediately. If multiple phone numbers are specified, each phone number will be tried once. If the attempt fails, .Nm exits immediately with a non-zero exit code. If it succeeds, then .Nm becomes a daemon, and returns an exit status of zero to its caller. The daemon exits automatically if the connection is dropped by the remote system, or it receives a .Dv TERM signal. .Sh DIAL ON DEMAND Demand dialing is enabled with the .Fl auto or .Fl ddial options. You must also specify the destination label in .Pa /etc/ppp/ppp.conf to use. It must contain the .Dq set ifaddr command to define the remote peer's IP address. (refer to .Pa /etc/ppp/ppp.conf.sample ) .Bd -literal -offset indent # ppp -auto pmdemand ... # .Ed When .Fl auto or .Fl ddial is specified, .Nm runs as a daemon but you can still configure or examine its configuration by using the diagnostic port as follows (this can be done in .Fl background and .Fl direct mode too): .Bd -literal -offset indent # telnet localhost 3000 Trying 127.0.0.1... Connected to awfulhak. Escape character is '^]'. .... PPP on awfulhak> pass xxxx PPP ON awfulhak> show ipcp IPCP [OPEND] his side: xxxx .... .Ed .Pp Each .Nm daemon has an associated port number which is computed as "3000 + tunnel_device_number". In .Fl auto mode, when an outgoing packet is detected, .Nm will perform the dialing action (chat script) and try to connect with the peer. In .Fl ddial mode, the dialing action is performed any time the line is found to be down. If the connect fails, the default behavior is to wait 30 seconds and then attempt to connect when another outgoing packet is detected. This behavior can be changed with .Bd -literal -offset indent set redial seconds|random[.nseconds|random] [dial_attempts] .Ed .Pp .Sq Seconds is the number of seconds to wait before attempting to connect again. If the argument is .Sq random , the delay period is a random value between 0 and 30 seconds. .Sq Nseconds is the number of seconds to wait before attempting to dial the next number in a list of numbers (see the .Dq set phone command). The default is 3 seconds. Again, if the argument is .Sq random , the delay period is a random value between 0 and 30 seconds. .Sq dial_attempts is the number of times to try to connect for each outgoing packet that is received. The previous value is unchanged if this parameter is omitted. If a value of zero is specified for .Sq dial_attempts , .Nm ppp will keep trying until a connection is made. .Bd -literal -offset indent set redial 10.3 4 .Ed .Pp will attempt to connect 4 times for each outgoing packet that is detected with a 3 second delay between each number and a 10 second delay after all numbers have been tried. If multiple phone numbers are specified, the total number of attempts is still 4 (it does not attempt each number 4 times). Modifying the dial delay is very useful when running .Nm in demand dial mode on both ends of the link. If each end has the same timeout, both ends wind up calling each other at the same time if the link drops and both ends have packets queued. At some locations, the serial link may not be reliable, and carrier may be lost at inappropriate times. It is possible to have .Nm redial should carrier be unexpectedly lost during a session. .Bd -literal -offset indent set reconnect timeout ntries .Ed This command tells ppp to re-establish the connection .Ar ntries times on loss of carrier with a pause of .Ar timeout seconds before each try. For example, .Bd -literal -offset indent set reconnect 3 5 .Ed tells .Nm that on an unexpected loss of carrier, it should wait .Ar 3 seconds before attempting to reconnect. This may happen up to .Ar 5 times before .Nm gives up. The default value of ntries is zero (no reconnect). Care should be taken with this option. If the local timeout is slightly longer than the remote timeout, the reconnect feature will always be triggered (up to the given number of times) after the remote side times out and hangs up. NOTE: In this context, losing too many LQRs constitutes a loss of carrier and will trigger a reconnect. If the .Fl background flag is specified, all phone numbers are dialed at most once until a connection is made. The next number redial period specified with the .Dq set redial command is honoured, as is the reconnect tries value. If your redial value is less than the number of phone numbers specified, not all the specified numbers will be tried. To terminate the program, type PPP ON awfulhak> close ppp ON awfulhak> quit all .Pp A simple .Dq quit command will terminate the telnet connection but not the program itself. You must use .Dq quit all to terminate the program as well. .Sh RECEIVING INCOMING PPP CONNECTIONS (Method 1) To handle an incoming .Em PPP connection request, follow these steps: .Bl -enum .It Make sure the modem and (optionally) .Pa /etc/rc.serial is configured correctly. .Bl -bullet -compact .It Use Hardware Handshake (CTS/RTS) for flow control. .It Modem should be set to NO echo back (ATE0) and NO results string (ATQ1). .El .It Edit .Pa /etc/ttys to enable a getty on the port where the modem is attached. For example: .Dl ttyd1 "/usr/libexec/getty std.38400" dialup on secure Don't forget to send a .Dv HUP signal to the init process to start the getty. .Dl # kill -HUP 1 .It Prepare an account for the incoming user. .Bd -literal ppp:xxxx:66:66:PPP Login User:/home/ppp:/usr/local/bin/ppplogin .Ed .It Create a .Pa /usr/local/bin/ppplogin file with the following contents: .Bd -literal -offset indent #!/bin/sh -p exec /usr/sbin/ppp -direct .Ed (You can specify a label name for further control.) .Pp Direct mode ( .Fl direct ) lets .Nm work with stdin and stdout. You can also telnet to port 3000 to get command mode control in the same manner as client-side .Nm. .It Optional support for Microsoft's IPCP Name Server and NetBIOS Name Server negotiation can be enabled use .Dq enable msext and .Dq set ns pri-addr [sec-addr] along with .Dq set nbns pri-addr [sec-addr] in your ppp.conf file .El .Sh RECEIVING INCOMING PPP CONNECTIONS (Method 2) This method differs in that it recommends the use of .Em mgetty+sendfax to handle the modem connections. The latest version 0.99 can be compiled with the .Dq AUTO_PPP option to allow detection of clients speaking PPP to the login prompt. Follow these steps: .Bl -enum .It Get, configure, and install mgetty+sendfax v0.99 or later making sure you have used the AUTO_PPP option. .It Edit .Pa /etc/ttys to enable a mgetty on the port where the modem is attached. For example: .Dl cuaa1 "/usr/local/sbin/mgetty -s 57600" dialup on .It Prepare an account for the incoming user. .Bd -literal Pfred:xxxx:66:66:Fred's PPP:/home/ppp:/etc/ppp/ppp-dialup .Ed .It Examine the files .Pa /etc/ppp/sample.ppp-dialup .Pa /etc/ppp/sample.ppp-pap-dialup and .Pa /etc/ppp/ppp.conf.sample for ideas. ppp-pap-dialup is supposed to be called from .Pa /usr/local/etc/mgetty+sendfax/login.conf from a line like .Dl /AutoPPP/ - - /etc/ppp/ppp-pap-dialup .El .Sh PACKET ALIASING The .Fl alias command line option enables packet aliasing. This allows the ppp host to act as a masquerading gateway for other computers over a local area network. Outgoing IP packets are aliased so that they appear to come from the ppp host, and incoming packets are de-aliased so that they are routed to the correct machine on the local area network. Packet aliasing allows computers on private, unregistered subnets to have internet access, although they are invisible from the outside world. In general, correct ppp operation should first be verified with packet aliasing disabled. Then, the .Fl alias option should be switched on, and network applications (web browser, telnet, ftp, ping, traceroute) should be checked on the ppp host. Finally, the same or similar applications should be checked on other computers in the LAN. If network applications work correctly on the ppp host, but not on other machines in the LAN, then the masquerading software is working properly, but the host is either not forwarding or possibly receiving IP packets. Check that IP forwarding is enabled in .Pa /etc/rc.conf and that other machines have designated the ppp host as the gateway for the LAN. .Sh PACKET FILTERING This implementation supports packet filtering. There are three kinds of filters; ifilter, ofilter and dfilter. Here are the basics: .Bl -bullet -compact .It A filter definition has the following syntax: set filter-name rule-no action [src_addr/src_width] [dst_addr/dst_width] [proto [src [lt|eq|gt] port ]] [dst [lt|eq|gt] port] [estab] .Bl -enum .It .Sq filter-name should be one of ifilter, ofilter, or dfilter. .It There are two actions: .Sq permit and .Sq deny . If a given packet matches the rule, the associated action is taken immediately. .It .Sq src_width and .Sq dst_width work like a netmask to represent an address range. .It .Sq proto must be one of icmp, udp or tcp. .It .Sq port number can be specified by number and service name from .Pa /etc/services . .El .It Each filter can hold up to 20 rules, starting from rule 0. The entire rule set is not effective until rule 0 is defined, ie. the default is to allow everything through. .It If no rule is matched to a packet, that packet will be discarded (blocked). .It Use .Dq set filter-name -1 to flush all rules. .El See .Pa /etc/ppp/ppp.conf.filter.example . .Sh SETTING IDLE, LINE QUALITY REQUEST, RETRY TIMER To check/set idletimer, use the .Dq show timeout and .Dq set timeout [lqrtimer [retrytimer]] commands: .Bd -literal -offset indent ppp ON awfulhak> set timeout 600 .Ed The timeout period is measured in seconds, the default values for which are timeout = 180 or 3 min, lqrtimer = 30sec and retrytimer = 3sec. To disable the idle timer function, use the command .Bd -literal -offset indent ppp ON awfulhak> set timeout 0 .Ed In .Fl auto mode, an idle timeout causes the .Em PPP session to be closed, though the .Nm program itself remains running. Another trigger packet will cause it to attempt to reestablish the link. .Sh PREDICTOR-1 COMPRESSION This version supports CCP and Predictor type 1 compression based on the current IETF-draft specs. As a default behavior, .Nm will attempt to use (or be willing to accept) this capability when the peer agrees (or requests it). To disable CCP/predictor functionality completely, use the .Dq disable pred1 and .Dq deny pred1 commands. .Sh CONTROLLING IP ADDRESS .Nm uses IPCP to negotiate IP addresses. Each side of the connection specifies the IP address that it's willing to use, and if the requested IP address is acceptable then .Nm returns ACK to the requester. Otherwise, .Nm returns NAK to suggest that the peer use a different IP address. When both sides of the connection agree to accept the received request (and send ACK), IPCP is set to the open state and a network level connection is established. To control this IPCP behavior, this implementation has the .Dq set ifaddr command for defining the local and remote IP address: .Nm set ifaddr .Op src_addr Op dst_addr Op netmask Where, .Sq src_addr is the IP address that the local side is willing to use and .Sq dst_addr is the IP address which the remote side should use. .Sq netmask is interface netmask. .Bd -literal -offset indent set ifaddr 192.244.177.38 192.244.177.2 255.255.255.0 .Ed The above specification means: .Bl -bullet -compact .It I strongly want to use 192.244.177.38 as my IP address, and I'll disagree if the peer suggests that I use another address. .It I strongly insist that peer use 192.244.177.2 as own side address and don't permit it to use any IP address but 192.244.177.2. When peer request another IP address, I always suggest that it use 192.244.177.2. .It My interface netmask will be 255.255.255.0. .El This is all fine when each side has a pre-determined IP address, however it is often the case that one side is acting as a server which controls all IP addresses and the other side should obey the direction from it. In order to allow more flexible behavior, `ifaddr' variable allows the user to specify IP address more loosely: .Dl set ifaddr 192.244.177.38/24 192.244.177.2/20 A number followed by a slash (/) represent the number of bits significant in the IP address. The above example signifies that: .Bl -bullet -compact .It I'd like to use 192.244.177.38 as my address if it is possible, but I'll also accept any IP address between 192.244.177.0 and 192.244.177.255. .It I'd like to make him use 192.244.177.2 as his own address, but I'll also permit him to use any IP address between 192.244.176.0 and 192.244.191.255. .It As you may have already noticed, 192.244.177.2 is equivalent to saying 192.244.177.2/32. .It As an exception, 0 is equivalent to 0.0.0.0/0, meaning that I have no preferred IP address and will obey the remote peer's selection. When using zero, no routing table entries will be made until a connection is established. .It 192.244.177.2/0 means that I'll accept/permit any IP address but I'll try to insist that 192.244.177.2 be used first. .El .Sh CONNECTING WITH YOUR INTERNET SERVICE PROVIDER The following steps should be taken when connecting to your ISP: .Bl -enum .It Describe your provider's phone number(s) in the dial script using the .Dq set phone command. This command allows you to set multiple phone numbers for dialing and redialing separated by a colon (:). For example: .Bd -literal -offset indent set phone "1234567:2345678" .Ed .Pp Here, the first number is attempted. If the connection fails, the second number is attempted after the next number redial period. If the second number also fails, the first is tried again after the redial period has expired. The selected phone number is substituted for the \\T string in the .Dq set dial command (see below). .It Set up your redial requirements using .Dq set redial . For example, if you have a bad telephone line or your provider is usually engaged (not so common these days), you may want to specify the following: .Bd -literal -offset indent set redial 10 4 .Ed .Pp This says that up to 4 phone calls should be attempted with a pause of 10 seconds before dialing the first number again. .It Describe your login procedure using the .Dq set dial and .Dq set login commands. The .Dq set dial command is used to talk to your modem and establish a link with your ISP, for example: .Bd -literal -offset indent set dial "ABORT BUSY ABORT NO\\\\sCARRIER TIMEOUT 4 \\"\\" ATZ OK-ATZ-OK ATDT\\\\T TIMEOUT 60 CONNECT" .Ed .Pp This modem "chat" string means: .Bl -bullet .It Abort if the string "BUSY" or "NO CARRIER" are received. .It Set the timeout to 4. .It Expect nothing. .It Send ATZ. .It Expect OK. If that's not received, send ATZ and expect OK. .It Send ATDTxxxxxxx where xxxxxxx is the next number in the phone list from above. .It Set the timeout to 60. .It Wait for the CONNECT string. .El Once the connection is established, the login script is executed. This script is written in the same style as the dial script: .Bd -literal -offset indent set login "TIMEOUT 15 login:-\\\\r-login: awfulhak word: xxx ocol: PPP HELLO" .Ed .Pp This login "chat" string means: .Bl -bullet .It Set the timeout to 15 seconds. .It Expect "login:". If it's not received, send a carriage return and expect "login:" again. .It Send "awfulhak" .It Expect "word:" (the tail end of a "Password:" prompt). .It Send "xxx". .It Expect "ocol:" (the tail end of a "Protocol:" prompt). .It Send "PPP". .It Expect "HELLO". .El .Pp Login scripts vary greatly between ISPs. .It Use .Dq set line and .Dq set sp to specify your serial line and speed, for example: .Bd -literal -offset indent set line /dev/cuaa0 set sp 115200 .Ed .Pp Cuaa0 is the first serial port on FreeBSD. Cuaa1 is the second etc. A speed of 115200 should be specified if you have a modem capable of bit rates of 28800 or more. In general, the serial speed should be about four times the modem speed. .It Use .Dq set ifaddr command to define the IP address. .Bl -bullet .It If you know what IP address your provider uses, then use it as the remote address, otherwise choose something like 10.0.0.2/0 (see below). .It If your provider has assigned a particular IP address to you, then use it as your address. .It If your provider assigns your address dynamically, choose a suitably unobtrusive and unspecific IP number as your address. 10.0.0.1/0 would be appropriate. The bit after the / specifies how many bits of the address you consider to be important, so if you wanted to insist on something in the class C network 1.2.3.0, you could specify 1.2.3.1/24. .El .Pp An example for a connection where you don't know your IP number or your ISPs IP number would be: .Bd -literal -offset indent set ifaddr 10.10.10.10/0 10.10.11.11/0 255.255.255.0 .Ed .It In most cases, your ISP will also be your default router. If this is the case, add the lines .Bd -literal -offset indent delete ALL add 0 0 10.10.11.11 .Ed .Pp to .Pa ppp.conf . .Pp This tells .Nm to delete all routing entries already made by .Nm , then to add a default route to HISADDR. HISADDR is a macro meaning the "other side"s IP number. .Pp If you're using dynamic IP numbers, you must also put these two lines in the .Pa ppp.linkup file. Then, once the link has been established and .Nm ppp knows the actual IP numbers in use, all previous (and probably incorrect) entries are deleted and a default to the correct IP number is added. Use the same label as the one used in .Pa ppp.conf . .Pp If commands are being typed interactively, the only requirement is to type .Bd -literal -offset indent add 0 0 HISADDR .Ed .Pp after a successful dial. .It If your provider requests that you use PAP/CHAP authentication methods, add the next lines to your .Pa ppp.conf file: .Bd -literal -offset indent enable pap (or enable chap) disable chap (or disable pap) set authname MyName set authkey MyPassword .Ed .El Please refer to .Pa /etc/ppp/ppp.conf.sample and .Pa /etc/ppp/ppp.linkup.sample for some real examples. The pmdemand label should be appropriate for most ISPs. .Sh LOGGING FACILITY .Nm is able to generate the following log info via .Xr syslog 3 : .Bl -column SMMMMMM -offset indent .It Li Async Dump async level packet in hex .It Li Carrier Log Chat lines with 'CARRIER' .It Li Chat Generate Chat script trace log .It Li Command Log commands executed .It Li Connect Generate complete Chat log .It Li Debug Log (very verbose) debug information .It Li HDLC Dump HDLC packet in hex .It Li LCP Generate LCP/IPCP packet trace .It Li Link Log address assignments and link up/down events .It Li LQM Generate LQR report .It Li Phase Phase transition log output .It Li TCP/IP Dump all TCP/IP packets .It Li TUN Include the tun device on each log line .It Li Warning Output to the terminal device. If there is currently no terminal, output is sent to the log file using LOG_WARNING. .It Li Error Output to both the terminal device and the log file using LOG_ERROR. .It Li Alert Output to the log file using LOG_ALERT .El The .Dq set log command allows you to set logging output level, of which multiple levels can be specified. The default is equivalent to .Dq set log Carrier Link Phase . If The first argument to .Dq set log begins with a '+' or a '-' character, the current log levels are not cleared, for example: .Bd -literal -offset indent PPP ON awfulhak> show log Log: Carrier Link Phase PPP ON awfulhak> set log -Link +tcp/ip PPP ON awfulhak> show log Log: Carrier Phase TCP/IP .Ed Log messages of level Warning, Error and Alert are not controlable using .Dq set log . .Sh PPP COMMAND LIST This section lists the available commands and their effect. They are usable either from an interactive ppp session, from a configuration file or from a telnet session. .Bl -tag -width 20 .It accept|deny|enable|disable option.... These directives tell .Nm how to negotiate the initial connection with the peer. Each .Dq option has a default of either accept or deny and enable or disable. .Dq Accept means that the option will be ACK'd if the peer asks for it. .Dq Deny means that the option will be NAK'd if the peer asks for it. .Dq Enable means that the option will be requested by us. .Dq Disable means that the option will not be requested by us. .Pp .Dq Option may be one of the following: .Bl -tag -width 20 .It vjcomp Default: Enabled and Accepted. This option decides if Van Jacobson header compression will be used. .It lqr Default: Enabled and Accepted. This option decides if Link Quality Requests will be sent. LQR is a protocol that allows .Nm to determine that the link is down without relying on the modems carrier detect. .It chap Default: Disabled and Accepted. CHAP stands for Challenge Handshake Authentication Protocol. Only one of CHAP and PAP (below) may be negotiated. With CHAP, the authenticator sends a "challenge" message to its peer. The peer uses a one-way hash function to encrypt the challenge and sends the result back. The authenticator does the same, and compares the results. The advantage of this mechanism is that no passwords are sent across the connection. A challenge is made when the connection is first made. Subsequent challenges may occur. When using CHAP, an .Dq AuthName and an .Dq AuthKey must be specified either in .Pa ppp.conf or in .Pa ppp.secret . .It pap Default: Disabled and Accepted. PAP stands for Password Authentication Protocol. Only one of PAP and CHAP (above) may be negotiated. With PAP, the ID and Password are sent repeatedly to the peer until authentication is acknowledged or the connection is terminated. This is a rather poor security mechanism. It is only performed when the connection is first established. When using PAP, an .Dq AuthName and an .Dq AuthKey must be specified either in .Pa ppp.conf or in .Pa ppp.secret (although see the .Dq passwdauth option below). .It acfcomp Default: Enabled and Accepted. ACFComp stands for Address and Control Field Compression. Non LCP packets usually have very similar address and control fields - making them easily compressable. .It protocomp Default: Enabled and Accepted. This option is used to negotiate PFC (Protocol Field Compression), a mechanism where the protocol field number is reduced to one octet rather than two. .It pred1 Default: Enabled and Accepted. This option decides if Predictor 1 compression will be used. .It proxy Default: Disabled and Denied. Unlike the other options (except passwdauth below), this is not negotiated with the peer. Therefore, accepting or denying it is of no use. Enabling this option will tell .Nm to proxy ARP for the peer. .It msext Default: Disabled and Accepted. This option allows the use of Microsoft's ppp extensions, supporting the negotiation of the Microsoft PPP DNS and the Microsoft NetBIOS NS. .It passwdauth Default: Disabled and Denied. Unlike the other options (except .Dq proxy above), this is not negotiated with the peer. Therefore, accepting or denying it is of no use. Enabling this option will tell the PAP authentication code to use the .Pa passwd file to authenticate the caller rather than the .Pa ppp.secret file. .El .It add dest mask gateway .Dq Dest is the destination IP address and .Dq mask is its mask. .Dq 0 0 refers to the default route. .Dq Gateway is the next hop gateway to get to the given .Dq dest machine/network. .It close Close the current connection (but don't quit). .It delete ALL | dest gateway [mask] If .Dq ALL is specified, all entries in the routing table created by .Nm are deleted. Otherwise, any existing route with the given .Dq dest , destination network .Dq mask and .Dq gateway is deleted. The default .Dq mask value is 0.0.0.0. .It dial|call [remote] If .Dq remote is specified, a connection is established using the .Dq dial and .Dq login scripts for the given .Dq remote system. Otherwise, the current settings are used to establish the connection. .It display Displays the current status of the negotiable protocol values as specified under .Dq accept|deny|enable|disable option.... above. .It passwd pass Specify the password required for access to the full .Nm command set. .It load [remote] Load the given .Dq remote label. If .Dq remote is not given, the .Dq default label is assumed. .It save This option is not (yet) implemented. .It set[up] var value This option allows the setting of any of the following variables: .Bl -tag -width 20 .It set accmap hex-value ACCMap stands for Asyncronous Control Character Map. This is always negotiated with the peer, and defaults to a value of 0x00000000. This protocol is required to defeat hardware that depends on passing certain characters from end to end (such as XON/XOFF etc). .It set filter-name rule-no action [src_addr/src_width] [dst_addr/dst_width] [proto [src [lt|eq|gt] port ]] [dst [lt|eq|gt] port] [estab] .Pp .Nm Ppp supports four filter sets. The afilter specifies packets that keep the connection alive - reseting the idle timer. The dfilter specifies packets that cause .Nm to dial when in .Fl auto mode. The ifilter specifies packets that are allowed to travel into the machine and the ofilter specifies packets that are allowed out of the machine. By default all filter sets allow all packets to pass. Rules are processed in order according to .Dq n . Up to 20 rules may be given for each set. If a packet doesn't match any of the rules in a given set, it is discarded. In the case of ifilters and ofilters, this means that the packet is dropped. In the case of afilters it means that the packet will not reset the idle timer and in the case of dfilters it means that the packet will not trigger a dial. Refer to the section on PACKET FILTERING above for further details. .It set authkey|key value This sets the authentication key (or password) used in PAP or CHAP negotiation to the given value. It can also be used to specify the password to be used in the dial or login scripts, preventing the actual password from being logged. .It set authname id This sets the authentication id used in PAP or CHAP negotiation. .It set ctsrts This sets hardware flow control and is the default. .It set device|line value This sets the device to which ppp will talk to the given value. .It set dial chat-script This specifies the chat script that will be used to dial the other side. See also the .Dv set login command below. Refer to .Xr chat 8 and to the example configuration files for details of the chat script format. The string \\\\T will be replaced with the current phone number (see .Dq set phone below) and the string \\\\P will be replaced with the password (see .Dq set key above). .It set escape value... This option is similar to the .Dq set accmap option above. It allows the user to specify a set of characters that will be `escaped' as they travel across the link. .It set ifaddr myaddr hisaddr mask This command specifies the IP addresses that will be used during LCP negotiation. Addresses are specified using the format .Dl a.b.c.d/n Where a.b.c.d is the preferred IP, but n specifies how many bits of the address we will insist on. If the /n bit is omitted, it defaults to /32 unless the IP address is 0.0.0.0 in which case the mask defaults to /0. .It set log [+|-]value... This command allows the adjustment of the current log level. Please refer to the Logging Facility section for further details. .It set login chat-script This chat-script compliments the dial-script. If both are specified, the login script will be executed after the dial script. Escape sequences available in the dial script are also available here. .It set mru value The default MRU is 1500. If it is increased, the other side *may* increase its mtu. There is no use decreasing the MRU to below the default as the PPP protocol *must* be able to accept packets of at least 1500 octets. .It set mtu value The default MTU is 1500. This may be increased by the MRU specified by the peer. It may only be subsequently decreased by this option. Increasing it is not valid as the peer is not necessarily able to receive the increased packet size. .It set openmode active|passive By default, openmode is always active. That is, .Nm will always initiate LCP negotiation. If you want to wait for the peer to initiate LCP negotiation, you may use the value .Dq passive . .It set parity odd|even|none|mark This allows the line parity to be set. The default value is none. .It set phone telno[:telno]... This allows the specification of the phone number to be used in place of the \\\\T string in the dial and login chat scripts. Multiple phone numbers may be given seperated by a colon (:). If multiple numbers are given, .Nm will dial them in rotation until a connection is made, retrying the maximum number of times specified by .Dq set redial below. In .Fl background mode, each number is attempted at most once. .It set reconnect timeout ntries Should the line drop unexpectedly (due to loss of CD or LQR failure), a connection will be re-established after the given .Dq timeout . The line will be re-connected at most .Dq ntries times. .Dq Ntries defaults to zero. A value of .Dq random for .Dq timeout will result in a variable pause, somewhere between 0 and 30 seconds. .It set redial seconds[.nseconds] [attempts] .Nm Ppp can be instructed to attempt to redial .Dq attempts times. If more than one number is specified (see .Dq set phone above), a pause of .Dq nseconds is taken before dialing each number. A pause of .Dq seconds is taken before starting at the first number again. A value of .Dq random may be used here too. .It set speed value This sets the speed of the serial device. .It set timeout Idle [ lqr [ retry ] ] This command allows the setting of the idle timer, the LQR timer (if enabled) and the retry timer. .It set ns x.x.x.x This option allows the setting of the Microsoft PPP DNS server that will be negotiated. .It set nbns This option allows the setting of the Microsoft NetBIOS DNS server that will be negotiated. .It set help|? This command gives a summary of available set commands. .El .It shell|! [command] Execute a shell according to the value of the .Dv SHELL environment variable. If .Dq command is specified, it is executed without a parent shell. Note, it's possible to use the .Dv HISADDR , .Dv INTERFACE and .Dv MYADDR symbols here. Also note that if you use the ! character, you must have a space between it and .Dq command . .It show var This command allows the user to examine the following: .Bl -tag -width 20 .It show [adio]filter List the current rules for the given filter. .It show auth Show the current authname and authkey. .It show ccp Show the current CCP statistics. .It show compress Show the current compress statistics. .It show escape Show the current escape characters. .It show hdlc Show the current HDLC statistics. .It show ipcp Show the current IPCP statistics. .It show lcp Show the current LCP statistics. .It show log Show the current log values. .It show mem Show current memory statistics. .It show modem Show current modem statistics. .It show mru Show the current MRU. .It show mtu Show the current MTU. .It show proto Show current protocol totals. .It show reconnect Show the current reconnect values. .It show redial Show the current redial values. .It show route Show the current routing tables. .It show timeout Show the current timeout values. .It show msext Show the current Microsoft extension values. .It show version Show the current version number of ppp. .It show help|? Give a summary of available show commands. .El .It term Go into terminal mode. Characters typed at the keyboard are sent to the modem. Characters read from the modem are displayed on the screen. When a .Nm peer is detected on the other side of the modem, .Nm automatically enables Packet Mode and goes back into command mode. .It alias ..... This command allows the control of the aliasing (or masquerading) facilities that are built into .Nm ppp . Until this code is required, it is not loaded by .Nm ppp , and it is quite possible that the alias library is not installed on your system (some administrators consider it a security risk). If aliasing is enabled on your system, the following commands are possible: .Bl -tag -width 20 .It alias enable [yes|no] This command either switches aliasing on or turns it off. The .Fl alias command line flag is synonomous with .Dq alias enable yes . .It alias port [proto targetIP:targetPORT [aliasIP:]aliasPORT] This command allows us to redirect connections arriving at .Dq aliasPORT for machine [aliasIP] to .Dq targetPORT on .Dq targetIP . If proto is specified, only connections of the given protocol are matched. This option is useful if you wish to things like internet phone on the machines behind your gateway. .It alias addr [addr_local addr_alias] This command allows data for .Dq addr_alias to be redirected to .Dq addr_local . It is useful if you own a small number of real IP numbers that you wish to map to specific machines behind your gateway. .It alias deny_incoming [yes|no] If set to yes, this command will refuse all incoming connections by dropping the packets in much the same way as a firewall would. .It alias log [yes|no] This option causes various aliasing statistics and information to be logged to the file .Pa /var/log/alias.log . .It alias same_ports [yes|no] When enabled, this command will tell the alias library attempt to avoid changing the port number on outgoing packets. This is useful if you want to support protocols such as RPC and LPD which require connections to come from a well known port. .It alias use_sockets [yes|no] When enabled, this option tells the alias library to create a socket so that it can guarantee a correct incoming ftp data or IRC connection. .It alias unregistered_only [yes|no] Only alter outgoing packets with an unregistered source ad- dress. According to rfc 1918, unregistered source addresses are 10.0.0.0/8, 172.16.0.0/12 and 192.168.0.0/16. .It alias help|? This command gives a summary of available alias commands. .El .It quit|bye [all] Exit .Nm ppp. If .Nm is in interactive mode or if the .Dq all argument is given, ppp will exit, closing the connection. A simple .Dq quit issued from a telnet session will not close the current connection. .It help|? [command] Show a list of available commands. If .Dq command is specified, show the usage string for that command. .It down Bring the link down ungracefully. It's not considered polite to use this command. .El .Sh MORE DETAILS .Bl -bullet -compact .It Read the example configuration files. They are a good source of information. .It Use .Dq help , .Dq show ? , .Dq alias ? , .Dq set ? and .Dq set ? commands. .El .Sh FILES .Nm Ppp refers to three files: ppp.conf, ppp.linkup and ppp.secret. These files are placed in .Pa /etc/ppp , but the user can create his own files under his $HOME directory as .Pa .ppp.conf , .Pa .ppp.linkup and .Pa .ppp.secret. .Nm will always try to consult the user's personal setup first. .Bl -tag -width flag .Pa $HOME/ppp/.ppp.[conf|linkup|secret] User dependent configuration files. .Pa /etc/ppp/ppp.conf System default configuration file. .Pa /etc/ppp/ppp.secret An authorization file for each system. .Pa /etc/ppp/ppp.linkup A file to check when .Nm establishes a network level connection. .Pa /var/log/ppp.tun0.log Logging and debugging information file. .Pa /var/spool/lock/LCK..* tty port locking file. Refer to .Xr uucplock 8 for further details. .Pa /var/run/tunX.pid The process id (pid) of the ppp program connected to the tunX device, where 'X' is the number of the device. This file is only created in .Fl background , .Fl auto and .Fl ddial modes. .Pa /var/run/ttyXX.pid The tun interface used by this port. Again, this file is only created in .Fl background , .Fl auto and .Fl ddial modes. .Pa /etc/services Get port number if port number is using service name. .El .Sh SEE ALSO .Xr chat 8 , .Xr pppd 8 , .Xr uucplock 3 , .Xr syslog 3 , .Xr syslog.conf 5 , .Xr syslogd 8 .Sh HISTORY This program was originally written by Toshiharu OHNO (tony-o@iij.ad.jp), and was submitted to FreeBSD-2.0.5 by Atsushi Murai (amurai@spec.co.jp). It's since had an enormous face lift and looks substantially different.