mirror of
https://git.savannah.gnu.org/git/emacs.git
synced 2024-12-15 09:47:20 +00:00
76 lines
1.9 KiB
Plaintext
76 lines
1.9 KiB
Plaintext
|
Date: Mon, 16 Feb 87 15:04:41 EST
|
|||
|
|
From: katinsky@gauss.rutgers.edu (David Katinsky)
|
|||
|
|
To: rms@prep.ai.mit.edu
|
|||
|
|
Subject: 3b2 procedure to raise MAXMEM
|
|||
|
|
|
|||
|
|
Below is the procedure I followed to allow enough memory for GnuEmacs to run
|
|||
|
|
on my 3b2/400. The end result of this is that a process can snarf up to 2Mb
|
|||
|
|
of memory. This can be a bit dangerous on a 2Mb machine, but I tried it and
|
|||
|
|
it worked ok.
|
|||
|
|
|
|||
|
|
-------------------------------------------------------------------------------
|
|||
|
|
|
|||
|
|
In the simplest case, these are the procedures to reconfigure a 3bx kernel.
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
1] cd /etc/master.d
|
|||
|
|
|
|||
|
|
`ls` shows the files to be:
|
|||
|
|
|
|||
|
|
README ctc* hdelog idisk ipc iuart kernel mau
|
|||
|
|
mem msg ports* prf sem shm stubs sxt
|
|||
|
|
sys xt
|
|||
|
|
|
|||
|
|
2] Edit the file which contains the parameter[s] you wish to change.
|
|||
|
|
In the following excerpt from /etc/master.d/kernel the value MAXMEM
|
|||
|
|
was raised from 256 to 1024.
|
|||
|
|
|
|||
|
|
In V.3.0 and later releases, the parameter in question is MAXUMEM
|
|||
|
|
instead of MAXMEM.
|
|||
|
|
|
|||
|
|
|
|||
|
|
*
|
|||
|
|
* The following entries form the tunable parameter table.
|
|||
|
|
*
|
|||
|
|
|
|||
|
|
|
|||
|
|
NCALL = 30
|
|||
|
|
NPROC = 60
|
|||
|
|
NTEXT = 58
|
|||
|
|
NCLIST = 188
|
|||
|
|
* maxmem is number of pages (2K) was 256 --dmk
|
|||
|
|
MAXMEM = 1024
|
|||
|
|
MAXUP = 25
|
|||
|
|
* hashbuf must be a power of 2
|
|||
|
|
NHBUF = 128
|
|||
|
|
NPBUF = 8
|
|||
|
|
|
|||
|
|
3] cd /boot
|
|||
|
|
|
|||
|
|
4] mkboot -k KERNEL
|
|||
|
|
|
|||
|
|
5] shutdown -i5 -g0 -y
|
|||
|
|
|
|||
|
|
This will take the machine down and bring it back up into firmware
|
|||
|
|
mode. When you see that the machine has reached this state, type the
|
|||
|
|
firmware password (default=mcp). The machine will ask for the name of
|
|||
|
|
a program to execute. At this prompt enter /etc/system . The machine
|
|||
|
|
should start to boot and display its configuration data.
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
8701271222 dmk
|
|||
|
|
|
|||
|
|
[katinsky@topaz.rutgers.edu]
|
|||
|
|
-------------------------------------------------------------------------------
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
I do not feel that having the default firmware password is a
|
|||
|
|
problem... but if you wish to edit it out, feel free.
|
|||
|
|
|
|||
|
|
dmk
|
|||
|
|
|
|||
|
|
|