mirror of
https://git.savannah.gnu.org/git/emacs.git
synced 2024-12-03 08:30:09 +00:00
222 lines
11 KiB
Plaintext
222 lines
11 KiB
Plaintext
The following text was written by someone at IBM to describe an older
|
|
version of the code for dumping on AIX. It does NOT apply to
|
|
the current version of Emacs. It is included in case someone
|
|
is curious.
|
|
|
|
|
|
I (rms) couldn't understand the code, and I can't fully understand
|
|
this text either. I rewrote the code to use the same basic
|
|
principles, as far as I understood them, but more cleanly. This
|
|
rewritten code does not always work. In fact, the basic method
|
|
seems to be intrinsically flawed.
|
|
|
|
Since then, someone else implemented a different way of dumping on
|
|
the RS/6000, which does seem to work. None of the following
|
|
applies to the way Emacs now dumps on the 6000. However, the
|
|
current method fails to use shared libraries. Anyone who might be
|
|
interested in trying to resurrect the previous method might still
|
|
find the following information useful.
|
|
|
|
|
|
It seems that the IBM dumping code was simply set up to detect when
|
|
the dumped data cannot be used, and in that case to act approximately
|
|
as if CANNOT_DUMP had been defined all along. (This is buried in
|
|
paragraph 1.) It seems simpler just to define CANNOT_DUMP, since
|
|
Emacs is not set up to decide at run time whether there is dumping or
|
|
not, and doing so correctly would be a lot of work.
|
|
|
|
Note that much of the other information, such as the name and format
|
|
of the dumped data file, has been changed.
|
|
|
|
|
|
--rms
|
|
|
|
|
|
|
|
A different approach has been taken to implement the
|
|
"dump/load" feature of GNU Emacs for AIX 3.1. Traditionally the
|
|
unexec function creates a new a.out executable file which contains
|
|
preloaded Lisp code. Executing the new a.out file (normally called
|
|
xemacs) provides rapid startup since the standard suite of Lisp code
|
|
is preloaded as part of the executable file.
|
|
|
|
AIX 3.1 architecture precludes the use of this technique
|
|
because the dynamic loader cannot guarantee a fixed starting location
|
|
for the process data section. The loader loads all shared library
|
|
data BEFORE process data. When a shared library changes its data
|
|
space, the process initial data section address (_data) will change
|
|
and all global process variables are automatically relocated to new
|
|
addresses. This invalidates the "dumped" Emacs executable which has
|
|
data addresses which are not relocatable and now corrupt. Emacs would
|
|
fail to execute until rebuilt with the new libraries.
|
|
|
|
To circumvent the dynamic loader feature of AIX 3.1, the dump process
|
|
has been modified as follows:
|
|
|
|
1) A new executable file is NOT created. Instead, both pure and
|
|
impure data are saved by the dump function and automatically
|
|
reloaded during process initialization. If any of the saved data
|
|
is unavailable or invalid, loadup.el will be automatically loaded.
|
|
|
|
2) Pure data is defined as a shared memory segment and attached
|
|
automatically as read-only data during initialization. This
|
|
allows the pure data to be a shared resource among all Emacs
|
|
processes. The shared memory segment size is PURESIZE bytes.
|
|
If the shared memory segment is unavailable or invalid, a new
|
|
shared memory segment is created and the impure data save file
|
|
is destroyed, forcing loadup.el to be reloaded.
|
|
|
|
3) The ipc key used to create and access Emacs shared memory is
|
|
SHMKEY and can be overridden by the environment symbol EMACSSHMKEY.
|
|
Only one ipc key is allowed per system. The environment symbol
|
|
is provided in case the default ipc key has already been used.
|
|
|
|
4) Impure data is written to the ../bin/.emacs.data file by the
|
|
dump function. This file contains the process' impure data
|
|
at the moment of load completion. During Emacs initialization,
|
|
the process' data section is expanded and overwritten
|
|
with the .emacs.data file contents.
|
|
|
|
The following are software notes concerning the GNU Emacs dump function under AIX 3.1:
|
|
|
|
1) All of the new dump/load code is activated by the #ifdef SHMKEY
|
|
conditional.
|
|
|
|
2) The automatic loading of loadup.el does NOT cause the dump function
|
|
to be performed. Therefore once the pure/impure data is discarded,
|
|
someone must remake Emacs to create the saved data files. This
|
|
should only be necessary when Emacs is first installed or whenever
|
|
AIX is upgraded.
|
|
|
|
3) Emacs will exit with an error if executed in a non-X environment
|
|
and the dump function was performed within a X window. Therefore
|
|
the dump function should always be performed in a non-X
|
|
environment unless the X environment will ALWAYS be available.
|
|
|
|
4) Emacs only maintains the lower 24 bits of any data address. The
|
|
remaining upper 8 bits are reset by the XPNTR macro whenever any
|
|
Lisp object is referenced. This poses a serious problem because
|
|
pure data is stored in segment 3 (shared memory) and impure data
|
|
is stored in segment 2 (data). To reset the upper 8 address bits
|
|
correctly, XPNTR must guess as to which type of data is represented
|
|
by the lower 24 address bits. The technique chosen is based upon
|
|
the fact that pure data offsets in segment 3 range from
|
|
0 -> PURESIZE-1, which are relatively small offsets. Impure data
|
|
offsets in segment 2 are relatively large (> 0x40000) because they
|
|
must follow all shared library data. Therefore XPNTR adds segment
|
|
3 to each data offset which is small (below PURESIZE) and adds
|
|
segment 2 to all other offsets. This algorithm will remain valid
|
|
as long as a) pure data size remains relatively small and b) process
|
|
data is loaded after shared library data.
|
|
|
|
To eliminate this guessing game, Emacs must preserve the 32-bit
|
|
address and add additional data object overhead for the object type
|
|
and garbage collection mark bit.
|
|
|
|
5) The data section written to .emacs.data is divided into three
|
|
areas as shown below. The file header contains four character
|
|
pointers which are used during automatic data loading. The file's
|
|
contents will only be used if the first three addresses match
|
|
their counterparts in the current process. The fourth address is
|
|
the new data segment address required to hold all of the preloaded
|
|
data.
|
|
|
|
|
|
.emacs.data file format
|
|
|
|
+---------------------------------------+ \
|
|
| address of _data | \
|
|
+---------------------------------------+ \
|
|
| address of _end | \
|
|
+---------------------------------------+ file header
|
|
| address of initial sbrk(0) | /
|
|
+---------------------------------------+ /
|
|
| address of final sbrk(0) | /
|
|
+---------------------------------------+ /
|
|
\ \
|
|
\ \
|
|
all data to be loaded from
|
|
_data to _end
|
|
\ \
|
|
\ \
|
|
+---------------------------------------+
|
|
\ \
|
|
\ \
|
|
all data to be loaded from
|
|
initial to final sbrk(0)
|
|
\ \
|
|
+---------------------------------------+
|
|
|
|
|
|
Sections two and three contain the preloaded data which is
|
|
restored at locations _data and initial sbrk(0) respectively.
|
|
|
|
The reason two separate sections are needed is that process
|
|
initialization allocates data (via malloc) prior to main()
|
|
being called. Therefore _end is several kbytes lower than
|
|
the address returned by an initial sbrk(0). This creates a
|
|
hole in the process data space and malloc will abort if this
|
|
region is overwritten during the load function.
|
|
|
|
One further complication with the malloc'd space is that it
|
|
is partially empty and must be "consumed" so that data space
|
|
malloc'd in the future is not assigned to this region. The malloc
|
|
function distributed with Emacs anticipates this problem but the
|
|
AIX 3.1 version does not. Therefore, repeated malloc calls are
|
|
needed to exhaust this initial malloc space. How do you know
|
|
when malloc has exhausted its free memory? You don't! So the
|
|
code must repeatedly call malloc for each buffer size and
|
|
detect when a new memory page has been allocated. Once the new
|
|
memory page is allocated, you can calculate the number of free
|
|
buffers in that page and request exactly that many more. Future
|
|
malloc requests will now be added at the top of a new memory page.
|
|
|
|
One final point - the initial sbrk(0) is the value of sbrk(0)
|
|
after all of the above malloc hacking has been performed.
|
|
|
|
|
|
The following Emacs dump/load issues need to be addressed:
|
|
|
|
1) Loadup.el exits with an error message because the xemacs and
|
|
emacs-xxx files are not created during the dump function.
|
|
|
|
Loadup.el should be changed to check for the new .emacs.data
|
|
file.
|
|
|
|
2) Dump will only support one .emacs.data file for the entire
|
|
system. This precludes the ability to allow each user to
|
|
define his/her own "dumped" Emacs.
|
|
|
|
Add an environment symbol to override the default .emacs.data
|
|
path.
|
|
|
|
3) An error message "error in init file" is displayed out of
|
|
startup.el when the dumped Emacs is invoked by a non-root user.
|
|
Although all of the preloaded Lisp code is present, the important
|
|
purify-flag has not been set back to Qnil - precluding the
|
|
loading of any further Lisp code until the flag is manually
|
|
reset.
|
|
|
|
The problem appears to be an access violation which will go
|
|
away if the read-write access modes to all of the files are
|
|
changed to rw-.
|
|
|
|
4) In general, all file access modes should be changed from
|
|
rw-r--r-- to rw-rw-rw-. They are currently setup to match
|
|
standard AIX access modes.
|
|
|
|
5) The dump function is not invoked when the automatic load of
|
|
loadup.el is performed.
|
|
|
|
Perhaps the command arguments array should be expanded with
|
|
"dump" added to force an automatic dump.
|
|
|
|
6) The automatic initialization function alloc_shm will delete
|
|
the shared memory segment and .emacs.data file if the "dump"
|
|
command argument is found in ANY argument position. The
|
|
dump function will only take place in loadup.el if "dump"
|
|
is the third or fourth command argument.
|
|
|
|
Change alloc_shm to live by loadup.el rules.
|
|
|