XFree86 (3 or 4) to depend to when USE_XLIB is set.
XFREE86_VERSION defaults to 3 for now, but adventurous users can
override it in /etc/make.conf. When XFREE86_VERSION=3, USE_XLIB
will add a dependency to x11/XFree86; when it is set to 4, the
dependency will be to x11/XFree86-4-libraries. When
XFREE86_VERSION=4, the PKG_IGNORE_DEPENDS and ALWAYS_BUILD_DEPENDS
hacks to avoid messing with XFree86 are turned off.
Since XFree86 version 4 includes some software that used to be
separate ports, when XFREE86_VERSION=3 the following variables are
provided:
USE_DGS LIB_DEPENDS on x11/dgs
USE_FREETYPE LIB_DEPENDS on print/freetype
USE_MESA LIB_DEPENDS on graphics/Mesa3
USE_XPM LIB_DEPENDS on graphics/xpm
When XFREE86_VERSION=4, these variables have no effect. The
LIB_DEPENDS in the tree for the above four ports have all been
converted to the USE_* counterparts. For your information, this
is the count of the number of ports:
USE_DGS 0
USE_FREETYPE 16
USE_MESA 36
USE_XPM 236
There is a new variable, XAWVER, which is set to 6 when
XFREE86_VERSION=3 and 7 when XFREE86_VERSION=4. This is also
passed to PLIST_SUB so ports that build Xaw based shared libraries
can use this variable to substitute the shlib version number.
There is also a provision of using a separate mtree file for
XFREE86_VERSION=4, but that part is not enabled yet.
Reviewed by: the ports list
Tested by: make index (XFREE86_VERSION=3 only)
(2) Add hebrew to list of valid categories.
Submitted by: nbm
(1) Took out INSTALL_MANPAGES (not necessary anymore, porter should
set NO_INSTALL_MANPAGES for not calling "make install.man")
(2) Replaced most of DEPENDS with EXEC_DEPENDS and LIB_DEPENDS. These
are the entries I used:
EXEC_DEPENDS:
unzip:${PORTSDIR}/archivers/unzip
gmake:${PORTSDIR}/devel/gmake
wishx:${PORTSDIR}/lang/tclX
xli:${PORTSDIR}/graphics/xli
gs:${PORTSDIR}/print/ghostscript
gunshar:${PORTSDIR}/archivers/gshar+gunshar
hfs:${PORTSDIR}/utils/hfs
rman:${PORTSDIR}/utils/rman
LIB_DEPENDS:
tiff\\.3\\.:${PORTSDIR}/graphics/tiff
jpeg\\.5\\.:${PORTSDIR}/graphics/jpeg
Xpm\\.4\\.:${PORTSDIR}/graphics/xpm
tcl\\.7\\.:${PORTSDIR}/lang/tcl
tk\\.3\\.:${PORTSDIR}/x11/tk
xview\\.1\\.:${PORTSDIR}/x11/xview-lib
Xaw3d\\.:${PORTSDIR}/x11/Xaw3d
mpeg\\.1\\.:${PORTSDIR}/graphics/mpeg-lib
xview\\.3\\.:${PORTSDIR}/x11/xview-lib
BLT\\.1\\.:${PORTSDIR}/x11/blt
There are still some dependencies I can't figure out what exactly
is needed. If your port still has DEPENDS in it, please check it out!
1. Make MASTER_SITES entries contain a trailing /. Garrett says that
assuming a '/' seperator between entries in MASTER_SITES and entries
in DISTFILES is a dangerous assumption. This will also be taken
out of bsd.port.mk.
2. General clean-up. Some of these Makefiles were a little grim.
Make sure they're all in sync with the sometimes rapidly changing
bsd.port.mk! :)
3. Some small configuration tweaks to keep them compiling under the
most recent 2.0 - some things seem to have broken along our road
to release.
