1
0
mirror of https://git.FreeBSD.org/ports.git synced 2024-12-25 04:43:33 +00:00
freebsd-ports/www/smb_auth/files
..
patch-aa
patch-smb_auth.c
README

SMB proxy authentication module

Current version: 0.05
Released on    : 28 September 1999
Author         : Richard Huveneers
License        : GNU GPL

smb_auth is a proxy authentication module. With smb_auth you can
authenticate proxy users against an SMB server like Windows NT or Samba.

Download

The current version is smb_auth-0.05.tar.gz.

Highlights of new features:

   * Easier debugging (finally!)
   * More flexibility
   * Improved documentation

Requirements

   * Squid 2.0 or above, or another proxy server with the same
     authentication module interface.
     Squid 1.1 with Arjan de Vet's patch works fine too.
   * smb_auth needs Samba to talk SMB. If you don't have Samba installed on
     your proxy server, download and install Samba now. You don't need to
     start the Samba daemons, smb_auth only uses the Samba client
     utilities.

     Note to Samba 2.0 users: The -E option of smbclient does not work
     properly in Samba 2.0.3 and earlier, which breaks smb_auth. This has
     been fixed in Samba 2.0.4, so make sure you are using Samba 2.0.4 or
     later (the command "smbclient -h" shows the version number). If you
     prefer not to upgrade to Samba 2.0.4, you can apply this patch which
     fixes the bug.

Installation

   * Check the Makefile. Make sure that SAMBAPREFIX and INSTALLBIN are set
     correctly before running make.
   * Run "make", then "make install". This will install smb_auth and
     smb_auth.sh in the INSTALLBIN directory.

Primary domain controller setup

To get proxy access control by user and group, smb_auth reads the file
\netlogon\proxyauth on one of the domain controllers using the supplied
credentials. If reading this file returns "allow" then access will be
allowed, otherwise denied.

   * Create a file named "proxyauth" on the NETLOGON share of the primary
     domain controller. In case you have one or more backup domain
     controllers, I'm assuming you are replicating this share to the backup
     domain controllers. If you prefer, you can change the location of this
     file by using the -S option of smb_auth (see below).
   * Put just the one word "allow" in this file.
   * Assign "Read" access to the "proxyauth" file to all users or group
     which you want to allow access to the proxy.
   * If you want to allow access from multiple domains to your proxy,
     repeat the above steps for the other domains.

Configure Squid

You need to configure Squid for proxy authentication. If you have problems
doing this, have a look at the FAQ. While reading the FAQ, replace
ncsa_auth with smb_auth. Please pay attention to the REQUIRED keyword in
the proxy_auth acl. As an example, here are the relevant lines of my own
squid.conf file:

    authenticate_program /usr/local/bin/smb_auth -W MEDIA@VANTAGE
    acl domainusers proxy_auth REQUIRED
    http_access allow domainusers

smb_auth has several options. Most people will call smb_auth like this:

    smb_auth -W domainname

where domainname is the name of your domain. By default, smb_auth tries to
find a domain controller by broadcasting on the primary network interface.
If you want to broadcast on another interface (for instance, if you have
two ethernet interfaces installed), use:

    smb_auth -W domainname -B <broadcast IP address>

If you really want to specify the IP address of a domain controller
yourself, use:

    smb_auth -W domainname -U <IP address>

This might even work with a WINS server (untested, feedback appreciated).
If you have several domains from which you want to allow access to your
proxy, just add them:

    smb_auth -W domain1 -W domain2 -W domain3 ...

in this case all users (except those of domain1) have to specify their
username as domainname\username when authenticating. If your users are
lazy, you can abbreviate the domainnames like this:

    smb_auth -W domain1 -W domain2 -w d2 -W domain3 -w d3 ..

then users of domain2 can authenticate with d2\username instead of
domain2\username. You can also specify different broadcast addresses etc.
per domain. Note that you don't need an abbreviation for the first domain
since omitting a domainname implies authenticating against the first
domain.

If you want to authenticate users of domain1 against a domain controller of
domain2 (you must have a trust relationship between domain1 and domain2)
then you can use the -P option. This is called pass-through authentication
and is useful to manage access from multiple domains to the proxy server
centrally (using a single proxyauth file):

    smb_auth -W domain1 -P domain2 -W domain2 ..

If you want to change the location of the proxyauth file (for instance
because your NETLOGON share is located on a FAT filesystem) then you can
use the -S option to specify a different share (make sure you are
replicating this share to the backup domain controllers):

    smb_auth -W domain -S share

You can also change the name of the proxyauth file and store it in a
sub-directory of the share by appending the full pathname of the proxyauth
file to the sharename. You may use both forward slashes and backslashes to
separate directories and you may (not required) prepend a (back)slash to
the sharename:

    smb_auth -W domain -S /share/path/to/proxyauth

Troubleshooting

You can run smb_auth on the command-line using the same options as in your
squid.conf. To debug authentication you can additionally use the -d option
which will print debug information after each step, so you can determine
which step is failing.
Do not use the -d option in your squid.conf, this corrupts the
communication between Squid and smb_auth.

You need to feed one username and password (separated by a space character)
to smb_auth's standard input. After authenticating this username and
password, smb_auth will continue accepting such username/password
combinations until you close it's standard input by pressing Ctrl-D.

Here's the output of a succesful authentication, so you know how the output
should look like:

# smb_auth -W MEDIA@VANTAGE -d
richard xxxxxxxx
Domain name: MEDIA@VANTAGE
Pass-through authentication: no
Query address options:
Domain controller IP address: 192.168.1.2
Domain controller NETBIOS name: VEGA
Contents of //VEGA/NETLOGON/proxyauth: allow
OK

Still having problems?

Please e-mail me if you have problems compiling, installing or configuring
smb_auth. Suggestions are welcome too.
If somebody could comment on NT licensing issues of smb_auth, that would be
more than welcome.

TODO

These are the items currently on my todo list. If you need another feature
currently not available, just let me know. I will add it to this list and
who knows, it might even get implemented.

   * research if smbclient does encrypted passwords on demand or needs
     smb.conf option or something else.
   * research if Samba 2.0 is able to retrieve NT group membership directly
   * re-code the shell script in C. I used a shell script mainly to speedup
     development.
   * add a netbios name cache. This feature needs the previous one and will
     speed up smb_auth considerably.
   * research if linking smb_auth with the Samba code is worth the trouble.