Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
/*-
|
|
|
|
|
|
* Copyright (c) 1998,1999 S<EFBFBD>ren Schmidt
|
|
|
|
|
|
* All rights reserved.
|
|
|
|
|
|
*
|
|
|
|
|
|
* Redistribution and use in source and binary forms, with or without
|
|
|
|
|
|
* modification, are permitted provided that the following conditions
|
|
|
|
|
|
* are met:
|
|
|
|
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
|
|
|
|
* notice, this list of conditions and the following disclaimer,
|
|
|
|
|
|
* without modification, immediately at the beginning of the file.
|
|
|
|
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
|
|
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
|
|
|
|
* documentation and/or other materials provided with the distribution.
|
|
|
|
|
|
* 3. The name of the author may not be used to endorse or promote products
|
|
|
|
|
|
* derived from this software without specific prior written permission.
|
|
|
|
|
|
*
|
|
|
|
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
|
|
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
|
|
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
|
|
|
|
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
|
|
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
|
|
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
|
|
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
|
|
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
|
|
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
|
|
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
|
|
*
|
1999-04-21 10:58:07 +00:00
|
|
|
|
* $Id: ata-all.c,v 1.9 1999/04/21 07:26:25 peter Exp $
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
|
|
#include "ata.h"
|
|
|
|
|
|
#if NATA > 0
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#include "isa.h"
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include "pci.h"
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#include "atadisk.h"
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#include "opt_global.h"
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <sys/param.h>
|
|
|
|
|
|
#include <sys/systm.h>
|
|
|
|
|
|
#include <sys/kernel.h>
|
|
|
|
|
|
#include <sys/interrupt.h>
|
|
|
|
|
|
#include <sys/conf.h>
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#include <sys/module.h>
|
|
|
|
|
|
#include <sys/bus.h>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <sys/buf.h>
|
|
|
|
|
|
#include <sys/malloc.h>
|
|
|
|
|
|
#include <sys/devicestat.h>
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#include <vm/vm.h>
|
|
|
|
|
|
#include <vm/pmap.h>
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#include <machine/resource.h>
|
|
|
|
|
|
#include <machine/bus.h>
|
|
|
|
|
|
#include <sys/rman.h>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <machine/clock.h>
|
1999-04-16 21:22:55 +00:00
|
|
|
|
#ifdef __i386__
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#include <machine/smp.h>
|
1999-04-21 07:26:30 +00:00
|
|
|
|
#include <i386/isa/intr_machdep.h>
|
1999-04-16 21:22:55 +00:00
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <pci/pcivar.h>
|
|
|
|
|
|
#include <pci/pcireg.h>
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#include <isa/isavar.h>
|
1999-04-16 21:22:55 +00:00
|
|
|
|
#include <isa/isareg.h>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <dev/ata/ata-all.h>
|
|
|
|
|
|
#include <dev/ata/ata-disk.h>
|
|
|
|
|
|
#include <dev/ata/atapi-all.h>
|
|
|
|
|
|
|
|
|
|
|
|
/* misc defines */
|
|
|
|
|
|
#define UNIT(dev) (dev>>3 & 0x1f) /* assume 8 minor # per unit */
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#define MIN(a,b) ((a)>(b)?(b):(a))
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#if SMP == 0
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#define isa_apic_irq(x) x
|
|
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
|
|
|
|
|
/* prototypes */
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#if NPCI > 0
|
1999-04-21 07:26:30 +00:00
|
|
|
|
static void promise_intr(void *);
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#endif
|
1999-04-18 20:48:15 +00:00
|
|
|
|
static int32_t ata_probe(int32_t, int32_t, int32_t, device_t, int32_t *);
|
1999-04-21 07:26:30 +00:00
|
|
|
|
static void ataintr(void *);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
1999-04-10 18:53:35 +00:00
|
|
|
|
static int32_t atanlun = 0;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
struct ata_softc *atadevices[MAXATA];
|
1999-04-18 20:48:15 +00:00
|
|
|
|
static devclass_t ata_devclass;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#if NISA > 0
|
|
|
|
|
|
|
|
|
|
|
|
static int
|
|
|
|
|
|
ata_isaprobe(device_t dev)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
1999-04-18 20:48:15 +00:00
|
|
|
|
struct resource *port;
|
|
|
|
|
|
int rid;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
int32_t ctlr, res;
|
1999-04-21 10:58:07 +00:00
|
|
|
|
int32_t lun;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
|
|
|
|
|
|
/* Allocate the port range */
|
|
|
|
|
|
rid = 0;
|
|
|
|
|
|
port = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid, 0, ~0, 1, RF_ACTIVE);
|
|
|
|
|
|
if (!port)
|
|
|
|
|
|
return (ENOMEM);
|
|
|
|
|
|
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
for (ctlr = 0; ctlr < atanlun; ctlr++) {
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if (atadevices[ctlr]->ioaddr == rman_get_start(port)) {
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
printf("ata-isa%d: already registered as ata%d\n",
|
1999-04-18 20:48:15 +00:00
|
|
|
|
device_get_unit(dev), ctlr);
|
|
|
|
|
|
bus_release_resource(dev, SYS_RES_IOPORT, 0, port);
|
|
|
|
|
|
return ENXIO;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
}
|
1999-04-18 20:48:15 +00:00
|
|
|
|
|
1999-04-21 10:58:07 +00:00
|
|
|
|
lun = 0;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
res = ata_probe(rman_get_start(port), rman_get_start(port) + ATA_ALTPORT,
|
1999-04-21 10:58:07 +00:00
|
|
|
|
0, dev, &lun);
|
1999-04-18 20:48:15 +00:00
|
|
|
|
|
|
|
|
|
|
bus_release_resource(dev, SYS_RES_IOPORT, 0, port);
|
|
|
|
|
|
|
|
|
|
|
|
if (res) {
|
|
|
|
|
|
isa_set_portsize(dev, res);
|
|
|
|
|
|
return 0;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
return ENXIO;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
|
1999-04-18 20:48:15 +00:00
|
|
|
|
static int
|
|
|
|
|
|
ata_isaattach(device_t dev)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
1999-04-21 10:58:07 +00:00
|
|
|
|
struct ata_softc *scp;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
struct resource *port;
|
|
|
|
|
|
struct resource *irq;
|
|
|
|
|
|
void *ih;
|
1999-04-21 07:26:30 +00:00
|
|
|
|
int rid;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
|
|
|
|
|
|
/* Allocate the port range and interrupt */
|
|
|
|
|
|
rid = 0;
|
|
|
|
|
|
port = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid, 0, ~0, 1, RF_ACTIVE);
|
|
|
|
|
|
if (!port)
|
|
|
|
|
|
return (ENOMEM);
|
|
|
|
|
|
|
|
|
|
|
|
rid = 0;
|
|
|
|
|
|
irq = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0, 1, RF_ACTIVE);
|
|
|
|
|
|
if (!irq) {
|
|
|
|
|
|
bus_release_resource(dev, SYS_RES_IOPORT, 0, port);
|
|
|
|
|
|
return (ENOMEM);
|
|
|
|
|
|
}
|
1999-04-21 10:58:07 +00:00
|
|
|
|
scp = device_get_softc(dev);
|
|
|
|
|
|
return bus_setup_intr(dev, irq, ataintr, scp, &ih);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
|
1999-04-18 20:48:15 +00:00
|
|
|
|
static device_method_t ata_isa_methods[] = {
|
|
|
|
|
|
/* Device interface */
|
|
|
|
|
|
DEVMETHOD(device_probe, ata_isaprobe),
|
|
|
|
|
|
DEVMETHOD(device_attach, ata_isaattach),
|
|
|
|
|
|
{ 0, 0 }
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
};
|
|
|
|
|
|
|
1999-04-18 20:48:15 +00:00
|
|
|
|
static driver_t ata_isa_driver = {
|
1999-04-21 10:58:07 +00:00
|
|
|
|
"ata-isa",
|
1999-04-18 20:48:15 +00:00
|
|
|
|
ata_isa_methods,
|
|
|
|
|
|
DRIVER_TYPE_BIO,
|
|
|
|
|
|
sizeof(int),
|
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
|
|
DRIVER_MODULE(ata, isa, ata_isa_driver, ata_devclass, 0, 0);
|
|
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
|
|
#if NPCI > 0
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
|
|
|
|
|
static const char *
|
1999-04-18 20:48:15 +00:00
|
|
|
|
ata_pcimatch(device_t dev)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
|
|
|
|
|
u_int32_t data;
|
|
|
|
|
|
|
1999-04-18 20:48:15 +00:00
|
|
|
|
data = pci_read_config(dev, PCI_CLASS_REG, 4);
|
|
|
|
|
|
if (pci_get_class(dev) == PCIC_STORAGE &&
|
|
|
|
|
|
(pci_get_subclass(dev) == PCIS_STORAGE_IDE ||
|
|
|
|
|
|
pci_get_subclass(dev) == PCIS_STORAGE_RAID)) {
|
|
|
|
|
|
switch (pci_get_devid(dev)) {
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
case 0x12308086:
|
|
|
|
|
|
return "Intel PIIX IDE controller";
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
case 0x70108086:
|
|
|
|
|
|
return "Intel PIIX3 IDE controller";
|
|
|
|
|
|
case 0x71118086:
|
|
|
|
|
|
return "Intel PIIX4 IDE controller";
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
case 0x4d33105a:
|
|
|
|
|
|
return "Promise Ultra/33 IDE controller";
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
case 0x522910b9:
|
|
|
|
|
|
return "AcerLabs Aladdin IDE controller";
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#if 0
|
|
|
|
|
|
case 0x05711106:
|
|
|
|
|
|
return "VIA Apollo IDE controller";
|
1999-04-16 21:22:55 +00:00
|
|
|
|
case 0x06401095:
|
|
|
|
|
|
return "CMD 640 IDE controller";
|
|
|
|
|
|
case 0x06461095:
|
|
|
|
|
|
return "CMD 646 IDE controller";
|
1999-04-18 20:48:15 +00:00
|
|
|
|
case 0xc6931080:
|
|
|
|
|
|
return "Cypress 82C693 IDE controller";
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
case 0x01021078:
|
|
|
|
|
|
return "Cyrix 5530 IDE controller";
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
default:
|
1999-03-03 21:10:29 +00:00
|
|
|
|
return "Unknown PCI IDE controller";
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
}
|
|
|
|
|
|
return NULL;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
1999-04-18 20:48:15 +00:00
|
|
|
|
static int
|
|
|
|
|
|
ata_pciprobe(device_t dev)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
1999-04-18 20:48:15 +00:00
|
|
|
|
const char *desc = ata_pcimatch(dev);
|
|
|
|
|
|
if (desc) {
|
|
|
|
|
|
device_set_desc(dev, desc);
|
|
|
|
|
|
return 0;
|
|
|
|
|
|
}
|
|
|
|
|
|
else
|
|
|
|
|
|
return ENXIO;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
static int
|
|
|
|
|
|
ata_pciattach(device_t dev)
|
|
|
|
|
|
{
|
|
|
|
|
|
int unit = device_get_unit(dev);
|
1999-04-21 10:58:07 +00:00
|
|
|
|
struct ata_softc *scp;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
u_int32_t type;
|
|
|
|
|
|
u_int8_t class, subclass;
|
|
|
|
|
|
u_int32_t cmd;
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
int32_t iobase_1, iobase_2, altiobase_1, altiobase_2;
|
1999-04-10 18:53:35 +00:00
|
|
|
|
int32_t bmaddr_1 = 0, bmaddr_2 = 0, sysctrl = 0, irq1, irq2;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
int32_t lun;
|
|
|
|
|
|
|
|
|
|
|
|
/* set up vendor-specific stuff */
|
1999-04-18 20:48:15 +00:00
|
|
|
|
type = pci_get_devid(dev);
|
|
|
|
|
|
class = pci_get_class(dev);
|
|
|
|
|
|
subclass = pci_get_subclass(dev);
|
|
|
|
|
|
cmd = pci_read_config(dev, PCIR_COMMAND, 4);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
|
|
|
|
|
#ifdef ATA_DEBUG
|
1999-04-21 10:58:07 +00:00
|
|
|
|
printf("ata-pci%d: type=%08x class=%02x subclass=%02x cmd=%08x\n",
|
1999-04-18 20:48:15 +00:00
|
|
|
|
unit, type, class, subclass, cmd);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#endif
|
|
|
|
|
|
|
1999-04-10 18:53:35 +00:00
|
|
|
|
/* if this is a Promise controller handle it specially */
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
if (type == 0x4d33105a) {
|
1999-04-18 20:48:15 +00:00
|
|
|
|
iobase_1 = pci_read_config(dev, 0x10, 4) & 0xfffc;
|
|
|
|
|
|
altiobase_1 = pci_read_config(dev, 0x14, 4) & 0xfffc;
|
|
|
|
|
|
iobase_2 = pci_read_config(dev, 0x18, 4) & 0xfffc;
|
|
|
|
|
|
altiobase_2 = pci_read_config(dev, 0x1c, 4) & 0xfffc;
|
|
|
|
|
|
irq1 = irq2 = pci_read_config(dev, PCI_INTERRUPT_REG, 4) & 0xff;
|
|
|
|
|
|
bmaddr_1 = pci_read_config(dev, 0x20, 4) & 0xfffc;
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
bmaddr_2 = bmaddr_1 + ATA_BM_OFFSET1;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
sysctrl = (pci_read_config(dev, 0x20, 4) & 0xfffc) + 0x1c;
|
1999-04-10 18:53:35 +00:00
|
|
|
|
outb(bmaddr_1 + 0x1f, inb(bmaddr_1 + 0x1f) | 0x01);
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
printf("ata-pci%d: Busmastering DMA supported\n", unit);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
/* everybody else seems to do it this way */
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
else {
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if ((unit == 0) &&
|
|
|
|
|
|
(pci_get_progif(dev) & PCIP_STORAGE_IDE_MODEPRIM) == 0) {
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
iobase_1 = IO_WD1;
|
|
|
|
|
|
altiobase_1 = iobase_1 + ATA_ALTPORT;
|
|
|
|
|
|
irq1 = 14;
|
|
|
|
|
|
}
|
|
|
|
|
|
else {
|
1999-04-18 20:48:15 +00:00
|
|
|
|
iobase_1 = pci_read_config(dev, 0x10, 4) & 0xfffc;
|
|
|
|
|
|
altiobase_1 = pci_read_config(dev, 0x14, 4) & 0xfffc;
|
|
|
|
|
|
irq1 = pci_read_config(dev, PCI_INTERRUPT_REG, 4) & 0xff;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if ((unit == 0) &&
|
|
|
|
|
|
(pci_get_progif(dev) & PCIP_STORAGE_IDE_MODESEC) == 0) {
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
iobase_2 = IO_WD2;
|
|
|
|
|
|
altiobase_2 = iobase_2 + ATA_ALTPORT;
|
|
|
|
|
|
irq2 = 15;
|
|
|
|
|
|
}
|
|
|
|
|
|
else {
|
1999-04-18 20:48:15 +00:00
|
|
|
|
iobase_2 = pci_read_config(dev, 0x18, 4) & 0xfffc;
|
|
|
|
|
|
altiobase_2 = pci_read_config(dev, 0x1c, 4) & 0xfffc;
|
|
|
|
|
|
irq2 = pci_read_config(dev, PCI_INTERRUPT_REG, 4) & 0xff;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
|
|
|
|
|
|
/* is this controller busmaster capable ? */
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if (pci_get_progif(dev) & PCIP_STORAGE_IDE_MASTERDEV) {
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
/* is busmastering support turned on ? */
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if ((pci_read_config(dev, PCI_COMMAND_STATUS_REG, 4) & 5) == 5) {
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
/* is there a valid port range to connect to ? */
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if ((bmaddr_1 = pci_read_config(dev, 0x20, 4) & 0xfffc)) {
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
bmaddr_2 = bmaddr_1 + ATA_BM_OFFSET1;
|
|
|
|
|
|
printf("ata-pci%d: Busmastering DMA supported\n", unit);
|
|
|
|
|
|
}
|
|
|
|
|
|
else
|
|
|
|
|
|
printf("ata-pci%d: Busmastering DMA not configured\n",unit);
|
|
|
|
|
|
}
|
|
|
|
|
|
else
|
|
|
|
|
|
printf("ata-pci%d: Busmastering DMA not enabled\n", unit);
|
|
|
|
|
|
}
|
|
|
|
|
|
else
|
|
|
|
|
|
printf("ata-pci%d: Busmastering DMA not supported\n", unit);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
/* now probe the addresse found for "real" ATA/ATAPI hardware */
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
lun = 0;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if (ata_probe(iobase_1, altiobase_1, bmaddr_1, dev, &lun)) {
|
1999-04-21 10:58:07 +00:00
|
|
|
|
scp = atadevices[lun];
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
if (iobase_1 == IO_WD1)
|
1999-04-16 21:22:55 +00:00
|
|
|
|
#ifdef __i386__
|
1999-04-21 10:58:07 +00:00
|
|
|
|
inthand_add(device_get_nameunit(dev), irq1, ataintr, scp,
|
1999-04-21 07:26:30 +00:00
|
|
|
|
&bio_imask, INTR_EXCL);
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#endif
|
|
|
|
|
|
#ifdef __alpha__
|
1999-04-21 10:58:07 +00:00
|
|
|
|
alpha_platform_setup_ide_intr(0, ataintr, scp);
|
1999-04-16 21:22:55 +00:00
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
else {
|
1999-04-18 20:48:15 +00:00
|
|
|
|
struct resource *irq;
|
|
|
|
|
|
int rid = 0;
|
|
|
|
|
|
void *ih;
|
|
|
|
|
|
|
|
|
|
|
|
irq = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0,1,RF_ACTIVE);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
if (sysctrl)
|
1999-04-21 10:58:07 +00:00
|
|
|
|
bus_setup_intr(dev, irq, promise_intr, scp, &ih);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
else
|
1999-04-21 10:58:07 +00:00
|
|
|
|
bus_setup_intr(dev, irq, ataintr, scp, &ih);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
printf("ata%d at 0x%04x irq %d on ata-pci%d\n",
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
lun, iobase_1, isa_apic_irq(irq1), unit);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
lun = 1;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
if (ata_probe(iobase_2, altiobase_2, bmaddr_2, dev, &lun)) {
|
1999-04-21 10:58:07 +00:00
|
|
|
|
scp = atadevices[lun];
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
if (iobase_2 == IO_WD2)
|
1999-04-16 21:22:55 +00:00
|
|
|
|
#ifdef __i386__
|
1999-04-21 10:58:07 +00:00
|
|
|
|
inthand_add(device_get_nameunit(dev), irq2, ataintr, scp,
|
1999-04-21 07:26:30 +00:00
|
|
|
|
&bio_imask, INTR_EXCL);
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#endif
|
|
|
|
|
|
#ifdef __alpha__
|
1999-04-21 10:58:07 +00:00
|
|
|
|
alpha_platform_setup_ide_intr(1, ataintr, scp);
|
1999-04-16 21:22:55 +00:00
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
else {
|
1999-04-18 20:48:15 +00:00
|
|
|
|
struct resource *irq;
|
|
|
|
|
|
int rid = 0;
|
|
|
|
|
|
void *ih;
|
|
|
|
|
|
|
|
|
|
|
|
irq = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0,1,RF_ACTIVE);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
if (!sysctrl)
|
1999-04-21 10:58:07 +00:00
|
|
|
|
bus_setup_intr(dev, irq, ataintr, scp, &ih);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
printf("ata%d at 0x%04x irq %d on ata-pci%d\n",
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
lun, iobase_2, isa_apic_irq(irq2), unit);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
1999-04-18 20:48:15 +00:00
|
|
|
|
return 0;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
|
1999-04-18 20:48:15 +00:00
|
|
|
|
static device_method_t ata_pci_methods[] = {
|
|
|
|
|
|
/* Device interface */
|
|
|
|
|
|
DEVMETHOD(device_probe, ata_pciprobe),
|
|
|
|
|
|
DEVMETHOD(device_attach, ata_pciattach),
|
|
|
|
|
|
{ 0, 0 }
|
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
|
|
static driver_t ata_pci_driver = {
|
1999-04-21 10:58:07 +00:00
|
|
|
|
"ata-pci",
|
1999-04-18 20:48:15 +00:00
|
|
|
|
ata_pci_methods,
|
|
|
|
|
|
DRIVER_TYPE_BIO,
|
|
|
|
|
|
sizeof(int),
|
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
|
|
DRIVER_MODULE(ata, pci, ata_pci_driver, ata_devclass, 0, 0);
|
|
|
|
|
|
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
static void
|
1999-04-21 07:26:30 +00:00
|
|
|
|
promise_intr(void *data)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
1999-04-21 07:26:30 +00:00
|
|
|
|
struct ata_softc *scp = (struct ata_softc *)data;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
int32_t channel = inl((pci_read_config(scp->dev, 0x20, 4) & 0xfffc) + 0x1c);
|
1999-04-10 18:53:35 +00:00
|
|
|
|
|
|
|
|
|
|
if (channel & 0x00000400)
|
1999-04-21 07:26:30 +00:00
|
|
|
|
ataintr(data);
|
1999-04-10 18:53:35 +00:00
|
|
|
|
|
|
|
|
|
|
if (channel & 0x00004000)
|
1999-04-21 07:26:30 +00:00
|
|
|
|
ataintr(atadevices[scp->unit + 1]);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
|
|
|
|
|
static int32_t
|
1999-04-10 18:53:35 +00:00
|
|
|
|
ata_probe(int32_t ioaddr, int32_t altioaddr, int32_t bmaddr,
|
1999-04-18 20:48:15 +00:00
|
|
|
|
device_t dev, int32_t *unit)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
|
|
|
|
|
struct ata_softc *scp = atadevices[atanlun];
|
|
|
|
|
|
int32_t mask = 0;
|
|
|
|
|
|
int32_t timeout;
|
1999-03-03 21:10:29 +00:00
|
|
|
|
int32_t lun = atanlun;
|
|
|
|
|
|
u_int8_t status0, status1;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#ifdef ATA_STATIC_ID
|
|
|
|
|
|
atanlun++;
|
|
|
|
|
|
#endif
|
|
|
|
|
|
if (lun > MAXATA) {
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
printf("ata: unit out of range(%d)\n", lun);
|
1999-03-03 21:10:29 +00:00
|
|
|
|
return 0;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
if (scp) {
|
1999-03-03 21:10:29 +00:00
|
|
|
|
printf("ata%d: unit already attached\n", lun);
|
|
|
|
|
|
return 0;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
scp = malloc(sizeof(struct ata_softc), M_DEVBUF, M_NOWAIT);
|
|
|
|
|
|
if (scp == NULL) {
|
1999-03-03 21:10:29 +00:00
|
|
|
|
printf("ata%d: failed to allocate driver storage\n", lun);
|
|
|
|
|
|
return 0;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
bzero(scp, sizeof(struct ata_softc));
|
|
|
|
|
|
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
scp->unit = *unit;
|
|
|
|
|
|
scp->lun = lun;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
scp->ioaddr = ioaddr;
|
|
|
|
|
|
scp->altioaddr = altioaddr;
|
1999-03-07 21:49:14 +00:00
|
|
|
|
scp->active = ATA_IDLE;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
|
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata%d: iobase=0x%04x altiobase=0x%04x\n",
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
scp->lun, scp->ioaddr, scp->altioaddr);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
|
|
/* do we have any signs of ATA/ATAPI HW being present ? */
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, ATA_D_IBM | ATA_MASTER);
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
status0 = inb(scp->ioaddr + ATA_STATUS);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, ATA_D_IBM | ATA_SLAVE);
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
status1 = inb(scp->ioaddr + ATA_STATUS);
|
|
|
|
|
|
if ((status0 & 0xf8) != 0xf8)
|
|
|
|
|
|
mask |= 0x01;
|
|
|
|
|
|
if ((status1 & 0xf8) != 0xf8)
|
|
|
|
|
|
mask |= 0x02;
|
|
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata%d: mask=%02x status0=%02x status1=%02x\n",
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
scp->lun, mask, status0, status1);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#endif
|
|
|
|
|
|
if (!mask) {
|
|
|
|
|
|
free(scp, M_DEVBUF);
|
|
|
|
|
|
return 0;
|
|
|
|
|
|
}
|
|
|
|
|
|
/* assert reset for devices and wait for completition */
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, ATA_D_IBM | ATA_MASTER);
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
outb(scp->altioaddr, ATA_A_IDS | ATA_A_RESET);
|
|
|
|
|
|
DELAY(1000);
|
|
|
|
|
|
outb(scp->altioaddr, ATA_A_IDS);
|
|
|
|
|
|
DELAY(1000);
|
|
|
|
|
|
inb(scp->ioaddr + ATA_ERROR);
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
DELAY(1);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
outb(scp->altioaddr, ATA_A_4BIT);
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
|
|
|
|
|
|
/* wait for BUSY to go inactive */
|
|
|
|
|
|
for (timeout = 0; timeout < 30000*10; timeout++) {
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, ATA_D_IBM | ATA_MASTER);
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
status0 = inb(scp->ioaddr + ATA_STATUS);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, ATA_D_IBM | ATA_SLAVE);
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
status1 = inb(scp->ioaddr + ATA_STATUS);
|
|
|
|
|
|
if (mask == 0x01) /* wait for master only */
|
|
|
|
|
|
if (!(status0 & ATA_S_BSY))
|
|
|
|
|
|
break;
|
|
|
|
|
|
if (mask == 0x02) /* wait for slave only */
|
|
|
|
|
|
if (!(status1 & ATA_S_BSY))
|
|
|
|
|
|
break;
|
|
|
|
|
|
if (mask == 0x03) /* wait for both master & slave */
|
|
|
|
|
|
if (!(status0 & ATA_S_BSY) && !(status1 & ATA_S_BSY))
|
|
|
|
|
|
break;
|
|
|
|
|
|
DELAY(100);
|
|
|
|
|
|
}
|
|
|
|
|
|
if (status0 & ATA_S_BSY)
|
|
|
|
|
|
mask &= ~0x01;
|
|
|
|
|
|
if (status1 & ATA_S_BSY)
|
|
|
|
|
|
mask &= ~0x02;
|
|
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata%d: mask=%02x status0=%02x status1=%02x\n",
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
scp->lun, mask, status0, status1);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#endif
|
|
|
|
|
|
if (!mask) {
|
|
|
|
|
|
free(scp, M_DEVBUF);
|
|
|
|
|
|
return 0;
|
|
|
|
|
|
}
|
|
|
|
|
|
/*
|
|
|
|
|
|
* OK, we have at least one device on the chain,
|
|
|
|
|
|
* check for ATAPI signatures, if none check if its
|
|
|
|
|
|
* a good old ATA device.
|
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, (ATA_D_IBM | ATA_MASTER));
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
if (inb(scp->ioaddr + ATA_CYL_LSB) == ATAPI_MAGIC_LSB &&
|
|
|
|
|
|
inb(scp->ioaddr + ATA_CYL_MSB) == ATAPI_MAGIC_MSB) {
|
|
|
|
|
|
scp->devices |= ATA_ATAPI_MASTER;
|
|
|
|
|
|
}
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, (ATA_D_IBM | ATA_SLAVE));
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
if (inb(scp->ioaddr + ATA_CYL_LSB) == ATAPI_MAGIC_LSB &&
|
|
|
|
|
|
inb(scp->ioaddr + ATA_CYL_MSB) == ATAPI_MAGIC_MSB) {
|
|
|
|
|
|
scp->devices |= ATA_ATAPI_SLAVE;
|
|
|
|
|
|
}
|
|
|
|
|
|
if (status0 != 0x00 && !(scp->devices & ATA_ATAPI_MASTER)) {
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, (ATA_D_IBM | ATA_MASTER));
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_ERROR, 0x58);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_CYL_LSB, 0xa5);
|
|
|
|
|
|
if (inb(scp->ioaddr + ATA_ERROR) != 0x58 &&
|
|
|
|
|
|
inb(scp->ioaddr + ATA_CYL_LSB) == 0xa5) {
|
|
|
|
|
|
scp->devices |= ATA_ATA_MASTER;
|
|
|
|
|
|
}
|
|
|
|
|
|
}
|
|
|
|
|
|
if (status1 != 0x00 && !(scp->devices & ATA_ATAPI_SLAVE)) {
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, (ATA_D_IBM | ATA_SLAVE));
|
|
|
|
|
|
DELAY(1);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_ERROR, 0x58);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_CYL_LSB, 0xa5);
|
|
|
|
|
|
if (inb(scp->ioaddr + ATA_ERROR) != 0x58 &&
|
|
|
|
|
|
inb(scp->ioaddr + ATA_CYL_LSB) == 0xa5) {
|
|
|
|
|
|
scp->devices |= ATA_ATA_SLAVE;
|
|
|
|
|
|
}
|
|
|
|
|
|
}
|
|
|
|
|
|
#ifdef ATA_DEBUG
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
printf("ata%d: devices = 0x%x\n", scp->lun, scp->devices);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#endif
|
|
|
|
|
|
if (!scp->devices) {
|
|
|
|
|
|
free(scp, M_DEVBUF);
|
|
|
|
|
|
return 0;
|
|
|
|
|
|
}
|
|
|
|
|
|
bufq_init(&scp->ata_queue);
|
|
|
|
|
|
TAILQ_INIT(&scp->atapi_queue);
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
*unit = scp->lun;
|
1999-04-18 20:48:15 +00:00
|
|
|
|
scp->dev = dev;
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
if (bmaddr)
|
|
|
|
|
|
scp->bmaddr = bmaddr;
|
|
|
|
|
|
atadevices[scp->lun] = scp;
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#ifndef ATA_STATIC_ID
|
|
|
|
|
|
atanlun++;
|
|
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
return ATA_IOSIZE;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
1999-03-03 21:10:29 +00:00
|
|
|
|
static void
|
1999-04-21 07:26:30 +00:00
|
|
|
|
ataintr(void *data)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
|
|
|
|
|
struct ata_softc *scp;
|
|
|
|
|
|
struct atapi_request *atapi_request;
|
|
|
|
|
|
struct buf *ata_request;
|
1999-04-10 18:53:35 +00:00
|
|
|
|
u_int8_t status;
|
|
|
|
|
|
static int32_t intr_count = 0;
|
1999-04-21 07:26:30 +00:00
|
|
|
|
int unit;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
1999-04-21 07:26:30 +00:00
|
|
|
|
scp = (struct ata_softc *)data;
|
|
|
|
|
|
unit = scp->unit;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
|
|
|
|
|
/* find & call the responsible driver to process this interrupt */
|
|
|
|
|
|
switch (scp->active) {
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#if NATADISK > 0
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
case ATA_ACTIVE_ATA:
|
|
|
|
|
|
if ((ata_request = bufq_first(&scp->ata_queue)))
|
1999-03-07 21:49:14 +00:00
|
|
|
|
if (ad_interrupt(ata_request) == ATA_OP_CONTINUES)
|
|
|
|
|
|
return;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
break;
|
1999-03-03 21:10:29 +00:00
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
case ATA_ACTIVE_ATAPI:
|
|
|
|
|
|
if ((atapi_request = TAILQ_FIRST(&scp->atapi_queue)))
|
1999-03-07 21:49:14 +00:00
|
|
|
|
if (atapi_interrupt(atapi_request) == ATA_OP_CONTINUES)
|
|
|
|
|
|
return;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
break;
|
|
|
|
|
|
|
1999-03-05 09:43:30 +00:00
|
|
|
|
case ATA_WAIT_INTR:
|
|
|
|
|
|
wakeup((caddr_t)scp);
|
|
|
|
|
|
break;
|
|
|
|
|
|
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
case ATA_IGNORE_INTR:
|
|
|
|
|
|
break;
|
1999-03-03 21:10:29 +00:00
|
|
|
|
|
|
|
|
|
|
default:
|
|
|
|
|
|
case ATA_IDLE:
|
1999-04-10 18:53:35 +00:00
|
|
|
|
status = inb(scp->ioaddr + ATA_STATUS);
|
|
|
|
|
|
if (intr_count++ < 10)
|
|
|
|
|
|
printf("ata%d: unwanted interrupt %d status = %02x\n",
|
|
|
|
|
|
unit, intr_count, status);
|
1999-03-07 21:49:14 +00:00
|
|
|
|
return;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
1999-03-07 21:49:14 +00:00
|
|
|
|
scp->active = ATA_IDLE;
|
|
|
|
|
|
ata_start(scp);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
void
|
|
|
|
|
|
ata_start(struct ata_softc *scp)
|
|
|
|
|
|
{
|
|
|
|
|
|
struct buf *ata_request;
|
|
|
|
|
|
struct atapi_request *atapi_request;
|
|
|
|
|
|
|
|
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata_start: entered\n");
|
|
|
|
|
|
#endif
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
if (scp->active != ATA_IDLE) {
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
printf("ata: unwanted ata_start\n");
|
|
|
|
|
|
return;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#if NATADISK > 0
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
/* find & call the responsible driver if anything on ATA queue */
|
|
|
|
|
|
if ((ata_request = bufq_first(&scp->ata_queue))) {
|
|
|
|
|
|
scp->active = ATA_ACTIVE_ATA;
|
|
|
|
|
|
ad_transfer(ata_request);
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata_start: started ata, leaving\n");
|
|
|
|
|
|
#endif
|
|
|
|
|
|
return;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
|
|
|
|
|
/* find & call the responsible driver if anything on ATAPI queue */
|
|
|
|
|
|
if ((atapi_request = TAILQ_FIRST(&scp->atapi_queue))) {
|
|
|
|
|
|
scp->active = ATA_ACTIVE_ATAPI;
|
|
|
|
|
|
atapi_transfer(atapi_request);
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata_start: started atapi, leaving\n");
|
|
|
|
|
|
#endif
|
|
|
|
|
|
return;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
int32_t
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
ata_wait(struct ata_softc *scp, int32_t device, u_int8_t mask)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
|
|
|
|
|
u_int8_t status;
|
|
|
|
|
|
u_int32_t timeout = 0;
|
|
|
|
|
|
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
while (timeout++ <= 500000) { /* timeout 5 secs */
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
status = inb(scp->ioaddr + ATA_STATUS);
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
|
|
|
|
|
|
/* if drive fails status, reselect the drive just to be sure */
|
|
|
|
|
|
if (status == 0xff) {
|
|
|
|
|
|
printf("ata%d: %s: no status, reselecting device\n",
|
|
|
|
|
|
scp->lun, device?"slave":"master");
|
|
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, ATA_D_IBM | device);
|
1999-03-07 21:49:14 +00:00
|
|
|
|
DELAY(1);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
status = inb(scp->ioaddr + ATA_STATUS);
|
|
|
|
|
|
}
|
|
|
|
|
|
if (status == 0xff)
|
|
|
|
|
|
return -1;
|
|
|
|
|
|
scp->status = status;
|
|
|
|
|
|
if (!(status & ATA_S_BSY)) {
|
|
|
|
|
|
if (status & ATA_S_ERROR)
|
|
|
|
|
|
scp->error = inb(scp->ioaddr + ATA_ERROR);
|
|
|
|
|
|
if ((status & mask) == mask)
|
|
|
|
|
|
return (status & ATA_S_ERROR);
|
|
|
|
|
|
}
|
|
|
|
|
|
if (timeout > 1000)
|
|
|
|
|
|
DELAY(1000);
|
|
|
|
|
|
else
|
|
|
|
|
|
DELAY(10);
|
|
|
|
|
|
}
|
|
|
|
|
|
return -1;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
int32_t
|
1999-03-05 09:43:30 +00:00
|
|
|
|
ata_command(struct ata_softc *scp, int32_t device, u_int32_t command,
|
|
|
|
|
|
u_int32_t cylinder, u_int32_t head, u_int32_t sector,
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
u_int32_t count, u_int32_t feature, int32_t flags)
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
{
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata_command: addr=%04x, device=%02x, cmd=%02x, c=%d, h=%d, s=%d, count=%d, flags=%02x\n", scp->ioaddr, device, command, cylinder, head, sector, count, flags);
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
1999-03-07 21:49:14 +00:00
|
|
|
|
/* ready to issue command ? */
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
if (ata_wait(scp, device, 0) < 0) {
|
|
|
|
|
|
printf("ata%d: %s: timeout waiting to give command s=%02x e=%02x\n",
|
|
|
|
|
|
scp->lun, device?"slave":"master", scp->status, scp->error);
|
1999-03-05 09:43:30 +00:00
|
|
|
|
}
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
outb(scp->ioaddr + ATA_FEATURE, feature);
|
1999-03-05 09:43:30 +00:00
|
|
|
|
outb(scp->ioaddr + ATA_CYL_LSB, cylinder);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_CYL_MSB, cylinder >> 8);
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
outb(scp->ioaddr + ATA_DRIVE, ATA_D_IBM | device | head);
|
1999-03-05 09:43:30 +00:00
|
|
|
|
outb(scp->ioaddr + ATA_SECTOR, sector);
|
|
|
|
|
|
outb(scp->ioaddr + ATA_COUNT, count);
|
|
|
|
|
|
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
if (scp->active != ATA_IDLE && flags != ATA_IMMEDIATE)
|
1999-03-07 21:49:14 +00:00
|
|
|
|
printf("DANGER active=%d\n", scp->active);
|
|
|
|
|
|
|
1999-03-05 09:43:30 +00:00
|
|
|
|
switch (flags) {
|
|
|
|
|
|
case ATA_WAIT_INTR:
|
|
|
|
|
|
scp->active = ATA_WAIT_INTR;
|
|
|
|
|
|
outb(scp->ioaddr + ATA_CMD, command);
|
1999-03-07 21:49:14 +00:00
|
|
|
|
if (tsleep((caddr_t)scp, PRIBIO, "atacmd", 500)) {
|
1999-04-16 21:22:55 +00:00
|
|
|
|
printf("ata_command: timeout waiting for interrupt\n");
|
1999-03-07 21:49:14 +00:00
|
|
|
|
scp->active = ATA_IDLE;
|
|
|
|
|
|
return -1;
|
|
|
|
|
|
}
|
1999-03-05 09:43:30 +00:00
|
|
|
|
break;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
1999-03-05 09:43:30 +00:00
|
|
|
|
case ATA_IGNORE_INTR:
|
|
|
|
|
|
scp->active = ATA_IGNORE_INTR;
|
|
|
|
|
|
outb(scp->ioaddr + ATA_CMD, command);
|
|
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
|
|
case ATA_IMMEDIATE:
|
|
|
|
|
|
default:
|
|
|
|
|
|
outb(scp->ioaddr + ATA_CMD, command);
|
|
|
|
|
|
break;
|
|
|
|
|
|
}
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#ifdef ATA_DEBUG
|
|
|
|
|
|
printf("ata_command: leaving\n");
|
|
|
|
|
|
#endif
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
return 0;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
1999-03-05 09:43:30 +00:00
|
|
|
|
void
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
bswap(int8_t *buf, int32_t len)
|
|
|
|
|
|
{
|
|
|
|
|
|
u_int16_t *p = (u_int16_t*)(buf + len);
|
|
|
|
|
|
|
|
|
|
|
|
while (--p >= (u_int16_t*)buf)
|
|
|
|
|
|
*p = ntohs(*p);
|
|
|
|
|
|
}
|
|
|
|
|
|
|
1999-03-05 09:43:30 +00:00
|
|
|
|
void
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
btrim(int8_t *buf, int32_t len)
|
|
|
|
|
|
{
|
|
|
|
|
|
int8_t *p;
|
|
|
|
|
|
|
|
|
|
|
|
for (p = buf; p < buf+len; ++p)
|
|
|
|
|
|
if (!*p)
|
|
|
|
|
|
*p = ' ';
|
|
|
|
|
|
for (p = buf + len - 1; p >= buf && *p == ' '; --p)
|
|
|
|
|
|
*p = 0;
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
void
|
|
|
|
|
|
bpack(int8_t *src, int8_t *dst, int32_t len)
|
|
|
|
|
|
{
|
|
|
|
|
|
int32_t i, j, blank;
|
|
|
|
|
|
|
|
|
|
|
|
for (i = j = blank = 0 ; i < len-1; i++) {
|
|
|
|
|
|
if (blank && src[i] == ' ') continue;
|
|
|
|
|
|
if (blank && src[i] != ' ') {
|
|
|
|
|
|
dst[j++] = src[i];
|
|
|
|
|
|
blank = 0;
|
|
|
|
|
|
continue;
|
|
|
|
|
|
}
|
|
|
|
|
|
if (src[i] == ' ')
|
|
|
|
|
|
blank = 1;
|
|
|
|
|
|
dst[j++] = src[i];
|
|
|
|
|
|
}
|
|
|
|
|
|
dst[j] = 0x00;
|
|
|
|
|
|
}
|
Fourth update to the new ATA/ATAPI driver:
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-03-28 18:57:20 +00:00
|
|
|
|
#endif /* NATA > 0 */
|