mirror/freebsd
1
0
Fork 0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-20 11:11:24 +00:00
Code Issues Releases Activity
e07e817462
freebsd/sys/isa/sio.c

3293 lines
86 KiB
C
Raw Normal View History

Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*-
* Copyright (c) 1991 The Regents of the University of California.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the University of
* California, Berkeley and its contributors.
* 4. Neither the name of the University nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
* from: @(#)com.c 7.5 (Berkeley) 5/16/91
* from: i386/isa sio.c,v 1.234
*/
#include "opt_comconsole.h"
#include "opt_compat.h"
#include "opt_ddb.h"
#include "opt_sio.h"
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
#include "card.h"
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
#include "pci.h"
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
#include "sio.h"
/*
* Serial driver, based on 386BSD-0.1 com driver.
* Mostly rewritten to use pseudo-DMA.
* Works for National Semiconductor NS8250-NS16550AF UARTs.
* COM driver, based on HP dca driver.
*
* Changes for PC-Card integration:
* - Added PC-Card driver table and handlers
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/reboot.h>
#include <sys/malloc.h>
#include <sys/tty.h>
#include <sys/proc.h>
#include <sys/module.h>
#include <sys/conf.h>
#include <sys/dkstat.h>
#include <sys/fcntl.h>
#include <sys/interrupt.h>
#include <sys/kernel.h>
#include <sys/syslog.h>
#include <sys/sysctl.h>
#include <sys/bus.h>
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
#include <machine/bus_pio.h>
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
#include <machine/bus.h>
#include <sys/rman.h>
Isolate the Timecounter internals in their own two files. Make the public interface more systematically named. Remove the alternate method, it doesn't do any good, only ruins performance. Add counters to profile the usage of the 8 access functions. Apply the beer-ware to my code. The weird +/- counts are caused by two repocopies behind the scenes: kern/kern_clock.c -> kern/kern_tc.c sys/time.h -> sys/timetc.h (thanks peter!)
2000-03-20 14:09:06 +00:00
#include <sys/timetc.h>
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
#include <sys/timepps.h>
#include <isa/isareg.h>
#include <isa/isavar.h>
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
#if NPCI > 0
#include <pci/pcireg.h>
#include <pci/pcivar.h>
#endif
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
#include <machine/lock.h>
#include <machine/clock.h>
#include <machine/ipl.h>
#ifndef SMP
#include <machine/lock.h>
#endif
#include <machine/resource.h>
#include <isa/sioreg.h>
#ifdef COM_ESP
#include <isa/ic/esp.h>
#endif
#include <isa/ic/ns16550.h>
#ifndef __i386__
#define disable_intr()
#define enable_intr()
#endif
#ifdef SMP
#define disable_intr() COM_DISABLE_INTR()
#define enable_intr() COM_ENABLE_INTR()
#endif /* SMP */
#define LOTS_OF_EVENTS 64 /* helps separate urgent events from input */
#define CALLOUT_MASK 0x80
#define CONTROL_MASK 0x60
#define CONTROL_INIT_STATE 0x20
#define CONTROL_LOCK_STATE 0x40
#define DEV_TO_UNIT(dev) (MINOR_TO_UNIT(minor(dev)))
#define MINOR_MAGIC_MASK (CALLOUT_MASK | CONTROL_MASK)
#define MINOR_TO_UNIT(mynor) ((mynor) & ~MINOR_MAGIC_MASK)
#ifdef COM_MULTIPORT
/* checks in flags for multiport and which is multiport "master chip"
* for a given card
*/
#define COM_ISMULTIPORT(flags) ((flags) & 0x01)
#define COM_MPMASTER(flags) (((flags) >> 8) & 0x0ff)
#define COM_NOTAST4(flags) ((flags) & 0x04)
#endif /* COM_MULTIPORT */
#define COM_CONSOLE(flags) ((flags) & 0x10)
#define COM_FORCECONSOLE(flags) ((flags) & 0x20)
#define COM_LLCONSOLE(flags) ((flags) & 0x40)
#define COM_DEBUGGER(flags) ((flags) & 0x80)
#define COM_LOSESOUTINTS(flags) ((flags) & 0x08)
#define COM_NOFIFO(flags) ((flags) & 0x02)
#define COM_ST16650A(flags) ((flags) & 0x20000)
#define COM_C_NOPROBE (0x40000)
#define COM_NOPROBE(flags) ((flags) & COM_C_NOPROBE)
#define COM_C_IIR_TXRDYBUG (0x80000)
#define COM_IIR_TXRDYBUG(flags) ((flags) & COM_C_IIR_TXRDYBUG)
#define COM_FIFOSIZE(flags) (((flags) & 0xff000000) >> 24)
#define com_scr 7 /* scratch register for 16450-16550 (R/W) */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
#define sio_getreg(com, off) \
(bus_space_read_1((com)->bst, (com)->bsh, (off)))
#define sio_setreg(com, off, value) \
(bus_space_write_1((com)->bst, (com)->bsh, (off), (value)))
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* com state bits.
* (CS_BUSY | CS_TTGO) and (CS_BUSY | CS_TTGO | CS_ODEVREADY) must be higher
* than the other bits so that they can be tested as a group without masking
* off the low bits.
*
* The following com and tty flags correspond closely:
* CS_BUSY = TS_BUSY (maintained by comstart(), siopoll() and
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
* comstop())
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
* CS_TTGO = ~TS_TTSTOP (maintained by comparam() and comstart())
* CS_CTS_OFLOW = CCTS_OFLOW (maintained by comparam())
* CS_RTS_IFLOW = CRTS_IFLOW (maintained by comparam())
* TS_FLUSH is not used.
* XXX I think TIOCSETA doesn't clear TS_TTSTOP when it clears IXON.
* XXX CS_*FLOW should be CF_*FLOW in com->flags (control flags not state).
*/
#define CS_BUSY 0x80 /* output in progress */
#define CS_TTGO 0x40 /* output not stopped by XOFF */
#define CS_ODEVREADY 0x20 /* external device h/w ready (CTS) */
#define CS_CHECKMSR 1 /* check of MSR scheduled */
#define CS_CTS_OFLOW 2 /* use CTS output flow control */
#define CS_DTR_OFF 0x10 /* DTR held off */
#define CS_ODONE 4 /* output completed */
#define CS_RTS_IFLOW 8 /* use RTS input flow control */
#define CSE_BUSYCHECK 1 /* siobusycheck() scheduled */
static char const * const error_desc[] = {
#define CE_OVERRUN 0
"silo overflow",
#define CE_INTERRUPT_BUF_OVERFLOW 1
"interrupt-level buffer overflow",
#define CE_TTY_BUF_OVERFLOW 2
"tty-level buffer overflow",
};
#define CE_NTYPES 3
#define CE_RECORD(com, errnum) (++(com)->delta_error_counts[errnum])
/* types. XXX - should be elsewhere */
typedef u_int Port_t; /* hardware port */
typedef u_char bool_t; /* boolean */
/* queue of linear buffers */
struct lbq {
u_char *l_head; /* next char to process */
u_char *l_tail; /* one past the last char to process */
struct lbq *l_next; /* next in queue */
bool_t l_queued; /* nonzero if queued */
};
/* com device structure */
struct com_s {
u_int flags; /* Copy isa device flags */
u_char state; /* miscellaneous flag bits */
bool_t active_out; /* nonzero if the callout device is open */
u_char cfcr_image; /* copy of value written to CFCR */
#ifdef COM_ESP
bool_t esp; /* is this unit a hayes esp board? */
#endif
u_char extra_state; /* more flag bits, separate for order trick */
u_char fifo_image; /* copy of value written to FIFO */
bool_t hasfifo; /* nonzero for 16550 UARTs */
bool_t st16650a; /* Is a Startech 16650A or RTS/CTS compat */
bool_t loses_outints; /* nonzero if device loses output interrupts */
u_char mcr_image; /* copy of value written to MCR */
#ifdef COM_MULTIPORT
bool_t multiport; /* is this unit part of a multiport device? */
#endif /* COM_MULTIPORT */
bool_t no_irq; /* nonzero if irq is not attached */
bool_t gone; /* hardware disappeared */
bool_t poll; /* nonzero if polling is required */
bool_t poll_output; /* nonzero if polling for output is required */
int unit; /* unit number */
int dtr_wait; /* time to hold DTR down on close (* 1/hz) */
u_int tx_fifo_size;
u_int wopeners; /* # processes waiting for DCD in open() */
/*
* The high level of the driver never reads status registers directly
* because there would be too many side effects to handle conveniently.
* Instead, it reads copies of the registers stored here by the
* interrupt handler.
*/
u_char last_modem_status; /* last MSR read by intr handler */
u_char prev_modem_status; /* last MSR handled by high level */
u_char hotchar; /* ldisc-specific char to be handled ASAP */
u_char *ibuf; /* start of input buffer */
u_char *ibufend; /* end of input buffer */
u_char *ibufold; /* old input buffer, to be freed */
u_char *ihighwater; /* threshold in input buffer */
u_char *iptr; /* next free spot in input buffer */
int ibufsize; /* size of ibuf (not include error bytes) */
int ierroff; /* offset of error bytes in ibuf */
struct lbq obufq; /* head of queue of output buffers */
struct lbq obufs[2]; /* output buffers */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
bus_space_tag_t bst;
bus_space_handle_t bsh;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
Port_t data_port; /* i/o ports */
#ifdef COM_ESP
Port_t esp_port;
#endif
Port_t int_id_port;
Port_t modem_ctl_port;
Port_t line_status_port;
Port_t modem_status_port;
Port_t intr_ctl_port; /* Ports of IIR register */
struct tty *tp; /* cross reference */
/* Initial state. */
struct termios it_in; /* should be in struct tty */
struct termios it_out;
/* Lock state. */
struct termios lt_in; /* should be in struct tty */
struct termios lt_out;
bool_t do_timestamp;
bool_t do_dcd_timestamp;
struct timeval timestamp;
struct timeval dcd_timestamp;
struct pps_state pps;
u_long bytes_in; /* statistics */
u_long bytes_out;
u_int delta_error_counts[CE_NTYPES];
u_long error_counts[CE_NTYPES];
struct resource *irqres;
struct resource *ioportres;
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
void *cookie;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* Data area for output buffers. Someday we should build the output
* buffer queue without copying data.
*/
u_char obuf1[256];
u_char obuf2[256];
};
#ifdef COM_ESP
static int espattach __P((struct com_s *com, Port_t esp_port));
#endif
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
static int sioattach __P((device_t dev, int rid));
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static int sio_isa_attach __P((device_t dev));
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static timeout_t siobusycheck;
static timeout_t siodtrwakeup;
static void comhardclose __P((struct com_s *com));
static void sioinput __P((struct com_s *com));
static void siointr1 __P((struct com_s *com));
static void siointr __P((void *arg));
static int commctl __P((struct com_s *com, int bits, int how));
static int comparam __P((struct tty *tp, struct termios *t));
static swihand_t siopoll;
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
static int sioprobe __P((device_t dev, int xrid));
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static int sio_isa_probe __P((device_t dev));
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static void siosettimeout __P((void));
static int siosetwater __P((struct com_s *com, speed_t speed));
static void comstart __P((struct tty *tp));
This patch clears the way for removing a number of tty related fields in struct cdevsw: d_stop moved to struct tty. d_reset already unused. d_devtotty linkage now provided by dev_t->si_tty. These fields will be removed from struct cdevsw together with d_params and d_maxio Real Soon Now. The changes in this patch consist of: initialize dev->si_tty in *_open() initialize tty->t_stop remove devtotty functions rename ttpoll to ttypoll a few adjustments to these changes in the generic code a bump of __FreeBSD_version add a couple of FreeBSD tags
1999-09-25 16:21:39 +00:00
static void comstop __P((struct tty *tp, int rw));
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static timeout_t comwakeup;
static void disc_optim __P((struct tty *tp, struct termios *t,
struct com_s *com));
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
#if NCARD > 0
static int sio_pccard_attach __P((device_t dev));
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
static int sio_pccard_detach __P((device_t dev));
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static int sio_pccard_probe __P((device_t dev));
#endif /* NCARD > 0 */
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
#if NPCI > 0
static int sio_pci_attach __P((device_t dev));
static void sio_pci_kludge_unit __P((device_t dev));
static int sio_pci_probe __P((device_t dev));
#endif /* NPCI > 0 */
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static char driver_name[] = "sio";
/* table and macro for fast conversion from a unit number to its com struct */
static devclass_t sio_devclass;
#define com_addr(unit) ((struct com_s *) \
devclass_get_softc(sio_devclass, unit))
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static device_method_t sio_isa_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, sio_isa_probe),
DEVMETHOD(device_attach, sio_isa_attach),
{ 0, 0 }
};
static driver_t sio_isa_driver = {
driver_name,
sio_isa_methods,
sizeof(struct com_s),
};
#if NCARD > 0
static device_method_t sio_pccard_methods[] = {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/* Device interface */
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
DEVMETHOD(device_probe, sio_pccard_probe),
DEVMETHOD(device_attach, sio_pccard_attach),
DEVMETHOD(device_detach, sio_pccard_detach),
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{ 0, 0 }
};
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static driver_t sio_pccard_driver = {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
driver_name,
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
sio_pccard_methods,
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
sizeof(struct com_s),
};
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
#endif /* NCARD > 0 */
#if NPCI > 0
static device_method_t sio_pci_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, sio_pci_probe),
DEVMETHOD(device_attach, sio_pci_attach),
{ 0, 0 }
};
static driver_t sio_pci_driver = {
driver_name,
sio_pci_methods,
sizeof(struct com_s),
};
#endif /* NPCI > 0 */
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static d_open_t sioopen;
static d_close_t sioclose;
static d_read_t sioread;
static d_write_t siowrite;
static d_ioctl_t sioioctl;
#define CDEV_MAJOR 28
static struct cdevsw sio_cdevsw = {
/* open */ sioopen,
/* close */ sioclose,
/* read */ sioread,
/* write */ siowrite,
/* ioctl */ sioioctl,
This patch clears the way for removing a number of tty related fields in struct cdevsw: d_stop moved to struct tty. d_reset already unused. d_devtotty linkage now provided by dev_t->si_tty. These fields will be removed from struct cdevsw together with d_params and d_maxio Real Soon Now. The changes in this patch consist of: initialize dev->si_tty in *_open() initialize tty->t_stop remove devtotty functions rename ttpoll to ttypoll a few adjustments to these changes in the generic code a bump of __FreeBSD_version add a couple of FreeBSD tags
1999-09-25 16:21:39 +00:00
/* poll */ ttypoll,
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/* mmap */ nommap,
/* strategy */ nostrategy,
/* name */ driver_name,
/* maj */ CDEV_MAJOR,
/* dump */ nodump,
/* psize */ nopsize,
/* flags */ D_TTY,
/* bmaj */ -1
};
int comconsole = -1;
static volatile speed_t comdefaultrate = CONSPEED;
#ifdef __alpha__
static volatile speed_t gdbdefaultrate = CONSPEED;
#endif
static u_int com_events; /* input chars + weighted output completions */
static Port_t siocniobase;
static int siocnunit;
static Port_t siogdbiobase;
static int siogdbunit = -1;
static bool_t sio_registered;
static int sio_timeout;
static int sio_timeouts_until_log;
static struct callout_handle sio_timeout_handle
= CALLOUT_HANDLE_INITIALIZER(&sio_timeout_handle);
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
static int sio_numunits;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static struct speedtab comspeedtab[] = {
{ 0, 0 },
{ 50, COMBRD(50) },
{ 75, COMBRD(75) },
{ 110, COMBRD(110) },
{ 134, COMBRD(134) },
{ 150, COMBRD(150) },
{ 200, COMBRD(200) },
{ 300, COMBRD(300) },
{ 600, COMBRD(600) },
{ 1200, COMBRD(1200) },
{ 1800, COMBRD(1800) },
{ 2400, COMBRD(2400) },
{ 4800, COMBRD(4800) },
{ 9600, COMBRD(9600) },
{ 19200, COMBRD(19200) },
{ 38400, COMBRD(38400) },
{ 57600, COMBRD(57600) },
{ 115200, COMBRD(115200) },
{ -1, -1 }
};
#ifdef COM_ESP
/* XXX configure this properly. */
static Port_t likely_com_ports[] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, };
static Port_t likely_esp_ports[] = { 0x140, 0x180, 0x280, 0 };
#endif
/*
* handle sysctl read/write requests for console speed
*
* In addition to setting comdefaultrate for I/O through /dev/console,
* also set the initial and lock values for the /dev/ttyXX device
* if there is one associated with the console. Finally, if the /dev/tty
* device has already been open, change the speed on the open running port
* itself.
*/
static int
Previous commit changing SYSCTL_HANDLER_ARGS violated KNF. Pointed out by: bde
2000-07-04 11:25:35 +00:00
sysctl_machdep_comdefaultrate(SYSCTL_HANDLER_ARGS)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{
int error, s;
speed_t newspeed;
struct com_s *com;
struct tty *tp;
newspeed = comdefaultrate;
error = sysctl_handle_opaque(oidp, &newspeed, sizeof newspeed, req);
if (error || !req->newptr)
return (error);
comdefaultrate = newspeed;
if (comconsole < 0) /* serial console not selected? */
return (0);
com = com_addr(comconsole);
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return (ENXIO);
/*
* set the initial and lock rates for /dev/ttydXX and /dev/cuaXX
* (note, the lock rates really are boolean -- if non-zero, disallow
* speed changes)
*/
com->it_in.c_ispeed = com->it_in.c_ospeed =
com->lt_in.c_ispeed = com->lt_in.c_ospeed =
com->it_out.c_ispeed = com->it_out.c_ospeed =
com->lt_out.c_ispeed = com->lt_out.c_ospeed = comdefaultrate;
/*
* if we're open, change the running rate too
*/
tp = com->tp;
if (tp && (tp->t_state & TS_ISOPEN)) {
tp->t_termios.c_ispeed =
tp->t_termios.c_ospeed = comdefaultrate;
s = spltty();
error = comparam(tp, &tp->t_termios);
splx(s);
}
return error;
}
SYSCTL_PROC(_machdep, OID_AUTO, conspeed, CTLTYPE_INT | CTLFLAG_RW,
0, 0, sysctl_machdep_comdefaultrate, "I", "");
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
#define SET_FLAG(dev, bit) device_set_flags(dev, device_get_flags(dev) | (bit))
#define CLR_FLAG(dev, bit) device_set_flags(dev, device_get_flags(dev) & ~(bit))
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
#if NCARD > 0
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static int
sio_pccard_probe(dev)
device_t dev;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
/* Do not probe IRQ - pccard doesn't turn on the interrupt line */
/* until bus_setup_intr */
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
SET_FLAG(dev, COM_C_NOPROBE);
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
return (sioprobe(dev, 0));
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
}
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static int
sio_pccard_attach(dev)
device_t dev;
{
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
return (sioattach(dev, 0));
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
/*
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
* sio_detach - unload the driver and clear the table.
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
* XXX TODO:
* This is usually called when the card is ejected, but
* can be caused by a modunload of a controller driver.
* The idea is to reset the driver's view of the device
* and ensure that any driver entry points such as
* read and write do not hang.
*/
Fix the hang on card eject problem and maybe the hang on suspend problem. o Create new timeout routine so we don't detach the card inside a ISR but instead drop back to spl0 via a timeout of 0. o Actually delete the child of the pccard device rather than just faking it badly. o Fix sio, ed and ep to have pccard detach routines that are int rather than void. o Fix ep and ed pccard detach routines to use if_detach rather than just if_down. if_detach destroys the device, while if_down just marks it down. In this incarnation of the pccard things, we map the disable the slot action to detach the driver, which removes the driver from the device tree. When that is done, a panic would soon follow as the ifconfig tried to down the device. Didn't fix: o Should cache the pccard dev child's pointer in struct slot o remove now unused parts of struct slot o Any driver using softc after detach has been called. sio's softc used to be statically allocated, so you could check sc->gone, but that is now gone. o Didn't remove gone from softc of drivers that use the old pccard method. Didn't test: o ed driver changes o sio driver changes on pccards o suspend (no laptop or apm support on my desktop)
1999-12-01 07:38:54 +00:00
static int
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
sio_pccard_detach(dev)
device_t dev;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{
struct com_s *com;
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
com = (struct com_s *) device_get_softc(dev);
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL) {
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
device_printf(dev, "NULL com in siounload\n");
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
return (0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
com->gone = 1;
if (com->irqres) {
bus_teardown_intr(dev, com->irqres, com->cookie);
bus_release_resource(dev, SYS_RES_IRQ, 0, com->irqres);
}
if (com->ioportres)
bus_release_resource(dev, SYS_RES_IOPORT, 0, com->ioportres);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (com->tp && (com->tp->t_state & TS_ISOPEN)) {
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
device_printf(dev, "still open, forcing close\n");
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com->tp->t_gen++;
ttyclose(com->tp);
ttwakeup(com->tp);
ttwwakeup(com->tp);
} else {
if (com->ibuf != NULL)
free(com->ibuf, M_DEVBUF);
}
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
device_printf(dev, "unloaded\n");
Fix the hang on card eject problem and maybe the hang on suspend problem. o Create new timeout routine so we don't detach the card inside a ISR but instead drop back to spl0 via a timeout of 0. o Actually delete the child of the pccard device rather than just faking it badly. o Fix sio, ed and ep to have pccard detach routines that are int rather than void. o Fix ep and ed pccard detach routines to use if_detach rather than just if_down. if_detach destroys the device, while if_down just marks it down. In this incarnation of the pccard things, we map the disable the slot action to detach the driver, which removes the driver from the device tree. When that is done, a panic would soon follow as the ifconfig tried to down the device. Didn't fix: o Should cache the pccard dev child's pointer in struct slot o remove now unused parts of struct slot o Any driver using softc after detach has been called. sio's softc used to be statically allocated, so you could check sc->gone, but that is now gone. o Didn't remove gone from softc of drivers that use the old pccard method. Didn't test: o ed driver changes o sio driver changes on pccards o suspend (no laptop or apm support on my desktop)
1999-12-01 07:38:54 +00:00
return (0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
#endif /* NCARD > 0 */
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
#if NPCI > 0
struct pci_ids {
u_int32_t type;
const char *desc;
int rid;
};
static struct pci_ids pci_ids[] = {
{ 0x100812b9, "3COM PCI FaxModem", 0x10 },
{ 0x048011c1, "ActionTec 56k FAX PCI Modem", 0x14 },
{ 0x00000000, NULL, 0 }
};
static int
sio_pci_attach(dev)
device_t dev;
{
u_int32_t type;
struct pci_ids *id;
type = pci_get_devid(dev);
id = pci_ids;
while (id->type && id->type != type)
id++;
if (id->desc == NULL)
return (ENXIO);
sio_pci_kludge_unit(dev);
return (sioattach(dev, id->rid));
}
/*
* Don't cut and paste this to other drivers. It is a horrible kludge
* which will fail to work and also be unnecessary in future versions.
*/
static void
sio_pci_kludge_unit(dev)
device_t dev;
{
devclass_t dc;
int err;
int start;
int unit;
unit = 0;
start = 0;
while (resource_int_value("sio", unit, "port", &start) == 0 &&
start > 0)
unit++;
if (device_get_unit(dev) < unit) {
dc = device_get_devclass(dev);
while (devclass_get_device(dc, unit))
unit++;
device_printf(dev, "moving to sio%d\n", unit);
err = device_set_unit(dev, unit); /* EVIL DO NOT COPY */
if (err)
device_printf(dev, "error moving device %d\n", err);
}
}
static int
sio_pci_probe(dev)
device_t dev;
{
u_int32_t type;
struct pci_ids *id;
type = pci_get_devid(dev);
id = pci_ids;
while (id->type && id->type != type)
id++;
if (id->desc == NULL)
return (ENXIO);
device_set_desc(dev, id->desc);
return (sioprobe(dev, id->rid));
}
#endif /* NPCI > 0 */
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static struct isa_pnp_id sio_ids[] = {
{0x0005d041, "Standard PC COM port"}, /* PNP0500 */
{0x0105d041, "16550A-compatible COM port"}, /* PNP0501 */
{0x0205d041, "Multiport serial device (non-intelligent 16550)"}, /* PNP0502 */
{0x1005d041, "Generic IRDA-compatible device"}, /* PNP0510 */
{0x1105d041, "Generic IRDA-compatible device"}, /* PNP0511 */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
/* Devices that do not have a compatid */
Add ACH2012 - 5634BTS 56K Video Ready Modem. PR: kern/17351 Submitted by: Eric D. Futch <efutch@nyct.net>
2000-05-19 03:41:22 +00:00
{0x12206804, NULL}, /* ACH2012 - 5634BTS 56K Video Ready Modem */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x7602a904, NULL}, /* AEI0276 - 56K v.90 Fax Modem (LKT) */
{0x00007905, NULL}, /* AKY0000 - 56K Plug&Play Modem */
{0x01405407, NULL}, /* AZT4001 - AZT3000 PnP SOUND DEVICE, MODEM */
{0x56039008, NULL}, /* BDP0356 - Best Data 56x2 */
{0x36339008, NULL}, /* BDP3336 - Best Data Prods. 336F */
{0x0014490a, NULL}, /* BRI1400 - Boca 33.6 PnP */
{0x0015490a, NULL}, /* BRI1500 - Internal Fax Data */
{0x0034490a, NULL}, /* BRI3400 - Internal ACF Modem */
{0x00b4490a, NULL}, /* BRIB400 - Boca 56k PnP */
{0x0030320d, NULL}, /* CIR3000 - Cirrus Logic V43 */
Add another four device ID's for isa pnp modems. The USR's seem to use the same vendor and logical ID. The rest I am not sure whether they are vendor or logical, but it won't hurt if I've put a vendor ID here as merely will not match. These came from the old sio-pnp code, hence the uncertainty about which ID it is.
2000-01-18 09:30:58 +00:00
{0x0100440e, NULL}, /* CRD0001 - Cardinal MVP288IV ? */
Add a couple of new PnP IDs. o OZO800f - Zoom 2812 (56k Modem) PR: kern/18603 Submitted by: Matt Loschert <loschert@servint.com> o DAV0336 - DAVICOM 336PNP MODEM PR: kern/18608 Submitted by: Martijn Plak <martijn@be3.com>
2000-05-18 02:06:24 +00:00
{0x36033610, NULL}, /* DAV0336 - DAVICOM 336PNP MODEM */
Add the logical ID of FUJITSU Modem 33600 PNP/I2. PR: kern/18257 Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
2000-05-02 05:54:11 +00:00
{0x0000aa1a, NULL}, /* FUJ0000 - FUJITSU Modem 33600 PNP/I2 */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x1200c31e, NULL}, /* GVC0012 - VF1128HV-R9 (win modem?) */
{0x0303c31e, NULL}, /* GVC0303 - MaxTech 33.6 PnP D/F/V */
Recognize the GVC0505 (GVC 56k Faxmodem) as a sio device. Obtained from: Dan J Fraser <dfraser@capybara.org> (for NetBSD)
1999-12-27 05:02:25 +00:00
{0x0505c31e, NULL}, /* GVC0505 - GVC 56k Faxmodem */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x0050c31e, NULL}, /* GVC5000 - some GVC modem */
{0x3800f91e, NULL}, /* GWY0038 - Telepath with v.90 */
{0x9062f91e, NULL}, /* GWY6290 - Telepath with x2 Technology */
{0x0000f435, NULL}, /* MOT0000 - Motorola ModemSURFR 33.6 Intern */
{0x5015f435, NULL}, /* MOT1550 - Motorola ModemSURFR 56K Modem */
{0xf015f435, NULL}, /* MOT15F0 - Motorola VoiceSURFR 56K Modem */
{0x6045f435, NULL}, /* MOT4560 - Motorola ? */
{0x61e7a338, NULL}, /* NECE761 - 33.6Modem */
Add a couple of new PnP IDs. o OZO800f - Zoom 2812 (56k Modem) PR: kern/18603 Submitted by: Matt Loschert <loschert@servint.com> o DAV0336 - DAVICOM 336PNP MODEM PR: kern/18608 Submitted by: Martijn Plak <martijn@be3.com>
2000-05-18 02:06:24 +00:00
{0x0f804f3f, NULL}, /* OZO800f - Zoom 2812 (56k Modem) */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x39804f3f, NULL}, /* OZO8039 - Zoom 56k flex */
Recognize another modem, "PMC2430 - Pace 56 Voice Internal Modem" Submitted by: Mark Ovens <mark@ukug.uk.freebsd.org>
2000-03-05 14:44:05 +00:00
{0x3024a341, NULL}, /* PMC2430 - Pace 56 Voice Internal Modem */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x1000eb49, NULL}, /* ROK0010 - Rockwell ? */
{0x5002734a, NULL}, /* RSS0250 - 5614Jx3(G) Internal Modem */
Add RSS0262 - 5614Jx3[G] V90+K56Flex Modem. PR: kern/18168 Submitted by: Tony Voet <voet@engineer.com>
2000-05-19 10:02:15 +00:00
{0x6202734a, NULL}, /* RSS0262 - 5614Jx3[G] V90+K56Flex Modem */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0xc100ad4d, NULL}, /* SMM00C1 - Leopard 56k PnP */
Add another four device ID's for isa pnp modems. The USR's seem to use the same vendor and logical ID. The rest I am not sure whether they are vendor or logical, but it won't hurt if I've put a vendor ID here as merely will not match. These came from the old sio-pnp code, hence the uncertainty about which ID it is.
2000-01-18 09:30:58 +00:00
{0x9012b04e, NULL}, /* SUP1290 - Supra ? */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x1013b04e, NULL}, /* SUP1310 - SupraExpress 336i PnP */
{0x8013b04e, NULL}, /* SUP1380 - SupraExpress 288i PnP Voice */
{0x8113b04e, NULL}, /* SUP1381 - SupraExpress 336i PnP Voice */
{0x5016b04e, NULL}, /* SUP1650 - Supra 336i Sp Intl */
Add SUP1670 - Supra 336i V+ Intl. Since we update the PnP IDs more frequently than the core part of the sio driver, it might be good to move the PnP IDs to sio_isapnp.h or something like that. PR: i386/18828 Submitted by: J.P. King <jpk28@cam.ac.uk>
2000-05-26 11:41:08 +00:00
{0x7016b04e, NULL}, /* SUP1670 - Supra 336i V+ Intl */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x7420b04e, NULL}, /* SUP2070 - Supra ? */
{0x8020b04e, NULL}, /* SUP2080 - Supra ? */
{0x8420b04e, NULL}, /* SUP2084 - SupraExpress 56i PnP */
Add another four device ID's for isa pnp modems. The USR's seem to use the same vendor and logical ID. The rest I am not sure whether they are vendor or logical, but it won't hurt if I've put a vendor ID here as merely will not match. These came from the old sio-pnp code, hence the uncertainty about which ID it is.
2000-01-18 09:30:58 +00:00
{0x7121b04e, NULL}, /* SUP2171 - SupraExpress 56i Sp? */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x8024b04e, NULL}, /* SUP2480 - Supra ? */
{0x01007256, NULL}, /* USR0001 - U.S. Robotics Inc., Sportster W */
{0x02007256, NULL}, /* USR0002 - U.S. Robotics Inc. Sportster 33. */
{0x04007256, NULL}, /* USR0004 - USR Sportster 14.4k */
{0x06007256, NULL}, /* USR0006 - USR Sportster 33.6k */
Add another four device ID's for isa pnp modems. The USR's seem to use the same vendor and logical ID. The rest I am not sure whether they are vendor or logical, but it won't hurt if I've put a vendor ID here as merely will not match. These came from the old sio-pnp code, hence the uncertainty about which ID it is.
2000-01-18 09:30:58 +00:00
{0x11007256, NULL}, /* USR0011 - USR ? */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x01017256, NULL}, /* USR0101 - USR ? */
{0x30207256, NULL}, /* USR2030 - U.S.Robotics Inc. Sportster 560 */
{0x50207256, NULL}, /* USR2050 - U.S.Robotics Inc. Sportster 33. */
{0x70207256, NULL}, /* USR2070 - U.S.Robotics Inc. Sportster 560 */
{0x30307256, NULL}, /* USR3030 - U.S. Robotics 56K FAX INT */
{0x31307256, NULL}, /* USR3031 - U.S. Robotics 56K FAX INT */
Recognize USR3050 "U.S. Robotics 56K FAX INT" fax modem. PR: 17702 Submitted by: Scot W. Hetzel <hetzels@westbend.net>
2000-03-31 07:09:08 +00:00
{0x50307256, NULL}, /* USR3050 - U.S. Robotics 56K FAX INT */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x70307256, NULL}, /* USR3070 - U.S. Robotics 56K Voice INT */
Add another four device ID's for isa pnp modems. The USR's seem to use the same vendor and logical ID. The rest I am not sure whether they are vendor or logical, but it won't hurt if I've put a vendor ID here as merely will not match. These came from the old sio-pnp code, hence the uncertainty about which ID it is.
2000-01-18 09:30:58 +00:00
{0x90307256, NULL}, /* USR3090 - USR ? */
Extract a list of extra isa pnp modem ID's from NetBSD and OpenBSD. Some of these are bound to have a PNP05xx compatid, but there's no easy way to tell. Since it's just an ID list and uses the pnp header's description strings rather than encoding strings here, it doesn't seem to be too expensive to err on the safe side.
1999-12-21 09:16:03 +00:00
{0x90917256, NULL}, /* USR9190 - USR 56k Voice INT */
{0x0300695c, NULL}, /* WCI0003 - Fax/Voice/Modem/Speakphone/Asvd */
{0x61f7896a, NULL}, /* ZTIF761 - Zoom ComStar 33.6 */
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{0}
};
Add another four device ID's for isa pnp modems. The USR's seem to use the same vendor and logical ID. The rest I am not sure whether they are vendor or logical, but it won't hurt if I've put a vendor ID here as merely will not match. These came from the old sio-pnp code, hence the uncertainty about which ID it is.
2000-01-18 09:30:58 +00:00
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static int
sio_isa_probe(dev)
device_t dev;
{
/* Check isapnp ids */
if (ISA_PNP_PROBE(device_get_parent(dev), dev, sio_ids) == ENXIO)
return (ENXIO);
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
return (sioprobe(dev, 0));
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
}
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static int
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
sioprobe(dev, xrid)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
device_t dev;
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
int xrid;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
#if 0
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static bool_t already_init;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
device_t xdev;
#endif
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
struct com_s *com;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
bool_t failures[10];
int fn;
device_t idev;
Port_t iobase;
intrmask_t irqmap[4];
intrmask_t irqs;
u_char mcr_image;
int result;
Fix a pair of silly warnings that I introduced (that would have been nasty on an Alpha or some other sizeof(int) != sizeof(long) machine).
1999-12-06 17:52:20 +00:00
u_long xirq;
Make it build, copy from dev/sio/sio.c: isa_set_flags -> device_set_flags isa_get_flags -> device_get_flags
1999-09-08 13:46:54 +00:00
u_int flags = device_get_flags(dev);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
int rid;
struct resource *port;
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
rid = xrid;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
port = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid,
0, ~0, IO_COMSIZE, RF_ACTIVE);
if (!port)
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
return (ENXIO);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
com = device_get_softc(dev);
com->bst = rman_get_bustag(port);
com->bsh = rman_get_bushandle(port);
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
#if 0
/*
* XXX this is broken - when we are first called, there are no
* previously configured IO ports. We could hard code
* 0x3f8, 0x2f8, 0x3e8, 0x2e8 etc but that's probably worse.
* This code has been doing nothing since the conversion since
* "count" is zero the first time around.
*/
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (!already_init) {
/*
* Turn off MCR_IENABLE for all likely serial ports. An unused
* port with its MCR_IENABLE gate open will inhibit interrupts
* from any used port that shares the interrupt vector.
* XXX the gate enable is elsewhere for some multiports.
*/
device_t *devs;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
int count, i, xioport;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
devclass_get_devices(sio_devclass, &devs, &count);
for (i = 0; i < count; i++) {
xdev = devs[i];
Use bus_get_resource() instead of bus_get_resource_start() as the latter returns "0" on failure, which is indistinguishable from (say) irq 0. This should stop a couple of stray messages that turn up. Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to a normal interrupt. This might help pccard folks with a shared slot interrupt. This whole thing needs to be revisited.
1999-12-06 06:47:02 +00:00
if (device_is_enabled(xdev) &&
bus_get_resource(xdev, SYS_RES_IOPORT, 0, &xioport,
NULL) == 0)
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
outb(xioport + com_mcr, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
free(devs, M_TEMP);
already_init = TRUE;
}
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
#endif
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (COM_LLCONSOLE(flags)) {
printf("sio%d: reserved for low-level i/o\n",
device_get_unit(dev));
"Completed" the previous fix. Return ENOMEM on memory allocation failure in sioattach(), not ENXIO. Free resources before returning early in sioprobe() and sioattach().
2000-01-29 03:02:55 +00:00
bus_release_resource(dev, SYS_RES_IOPORT, rid, port);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return (ENXIO);
}
/*
* If the device is on a multiport card and has an AST/4
* compatible interrupt control register, initialize this
* register and prepare to leave MCR_IENABLE clear in the mcr.
* Otherwise, prepare to set MCR_IENABLE in the mcr.
* Point idev to the device struct giving the correct id_irq.
* This is the struct for the master device if there is one.
*/
idev = dev;
mcr_image = MCR_IENABLE;
#ifdef COM_MULTIPORT
Fixed regressions in rev.1.274: 1) Non-AST4 multiport cards were broken by bypassing the code that changes `idev' to the multiport master device. 2) AST4 multiport cards apparently were broken by inverting the test for the master device having an irq. 3) Error handling for nonexistent master devices was broken by removing a check for a null pointer. 4) `int' error codes returned by bus_get_resource() were assigned directly to the boolean variable com->no_irq. Probably harmless, since the boolean is implemented as a u_char. Submitted by: part 1) by Chris Radek <cradek@in221.inetnebr.com> part 2) by yokota Approved by: jkh
2000-02-15 17:29:09 +00:00
if (COM_ISMULTIPORT(flags)) {
Fix a pair of silly warnings that I introduced (that would have been nasty on an Alpha or some other sizeof(int) != sizeof(long) machine).
1999-12-06 17:52:20 +00:00
Port_t xiobase;
u_long io;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
idev = devclass_get_device(sio_devclass, COM_MPMASTER(flags));
if (idev == NULL) {
printf("sio%d: master device %d not configured\n",
device_get_unit(dev), COM_MPMASTER(flags));
idev = dev;
}
Fixed regressions in rev.1.274: 1) Non-AST4 multiport cards were broken by bypassing the code that changes `idev' to the multiport master device. 2) AST4 multiport cards apparently were broken by inverting the test for the master device having an irq. 3) Error handling for nonexistent master devices was broken by removing a check for a null pointer. 4) `int' error codes returned by bus_get_resource() were assigned directly to the boolean variable com->no_irq. Probably harmless, since the boolean is implemented as a u_char. Submitted by: part 1) by Chris Radek <cradek@in221.inetnebr.com> part 2) by yokota Approved by: jkh
2000-02-15 17:29:09 +00:00
if (!COM_NOTAST4(flags)) {
if (bus_get_resource(idev, SYS_RES_IOPORT, 0, &io,
NULL) == 0) {
xiobase = io;
if (bus_get_resource(idev, SYS_RES_IRQ, 0,
NULL, NULL) == 0)
outb(xiobase + com_scr, 0x80);
else
outb(xiobase + com_scr, 0);
}
mcr_image = 0;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
}
#endif /* COM_MULTIPORT */
Use bus_get_resource() instead of bus_get_resource_start() as the latter returns "0" on failure, which is indistinguishable from (say) irq 0. This should stop a couple of stray messages that turn up. Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to a normal interrupt. This might help pccard folks with a shared slot interrupt. This whole thing needs to be revisited.
1999-12-06 06:47:02 +00:00
if (bus_get_resource(idev, SYS_RES_IRQ, 0, NULL, NULL) != 0)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
mcr_image = 0;
bzero(failures, sizeof failures);
iobase = rman_get_start(port);
/*
* We don't want to get actual interrupts, just masked ones.
* Interrupts from this line should already be masked in the ICU,
* but mask them in the processor as well in case there are some
* (misconfigured) shared interrupts.
*/
disable_intr();
/* EXTRA DELAY? */
/*
* Initialize the speed and the word size and wait long enough to
* drain the maximum of 16 bytes of junk in device output queues.
* The speed is undefined after a master reset and must be set
* before relying on anything related to output. There may be
* junk after a (very fast) soft reboot and (apparently) after
* master reset.
* XXX what about the UART bug avoided by waiting in comparam()?
* We don't want to to wait long enough to drain at 2 bps.
*/
if (iobase == siocniobase)
DELAY((16 + 1) * 1000000 / (comdefaultrate / 10));
else {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, CFCR_DLAB | CFCR_8BITS);
sio_setreg(com, com_dlbl, COMBRD(SIO_TEST_SPEED) & 0xff);
sio_setreg(com, com_dlbh, (u_int) COMBRD(SIO_TEST_SPEED) >> 8);
sio_setreg(com, com_cfcr, CFCR_8BITS);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY((16 + 1) * 1000000 / (SIO_TEST_SPEED / 10));
}
/*
* Enable the interrupt gate and disable device interupts. This
* should leave the device driving the interrupt line low and
* guarantee an edge trigger if an interrupt can be generated.
*/
/* EXTRA DELAY? */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_mcr, mcr_image);
sio_setreg(com, com_ier, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY(1000); /* XXX */
irqmap[0] = isa_irq_pending();
/*
* Attempt to set loopback mode so that we can send a null byte
* without annoying any external device.
*/
/* EXTRA DELAY? */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_mcr, mcr_image | MCR_LOOPBACK);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* Attempt to generate an output interrupt. On 8250's, setting
* IER_ETXRDY generates an interrupt independent of the current
* setting and independent of whether the THR is empty. On 16450's,
* setting IER_ETXRDY generates an interrupt independent of the
* current setting. On 16550A's, setting IER_ETXRDY only
* generates an interrupt when IER_ETXRDY is not already set.
*/
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_ier, IER_ETXRDY);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* On some 16x50 incompatibles, setting IER_ETXRDY doesn't generate
* an interrupt. They'd better generate one for actually doing
* output. Loopback may be broken on the same incompatibles but
* it's unlikely to do more than allow the null byte out.
*/
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_data, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY((1 + 2) * 1000000 / (SIO_TEST_SPEED / 10));
/*
* Turn off loopback mode so that the interrupt gate works again
* (MCR_IENABLE was hidden). This should leave the device driving
* an interrupt line high. It doesn't matter if the interrupt
* line oscillates while we are not looking at it, since interrupts
* are disabled.
*/
/* EXTRA DELAY? */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_mcr, mcr_image);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
* Some pcmcia cards have the "TXRDY bug", so we check everyone
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
* for IIR_TXRDY implementation ( Palido 321s, DC-1S... )
*/
Argh, don't turn the IIR test on unless it's a pccard. These tests mess up the subsequent probes.
1999-11-18 10:29:06 +00:00
if (COM_NOPROBE(flags)) {
/* Reading IIR register twice */
for (fn = 0; fn < 2; fn ++) {
DELAY(10000);
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
failures[6] = sio_getreg(com, com_iir);
Argh, don't turn the IIR test on unless it's a pccard. These tests mess up the subsequent probes.
1999-11-18 10:29:06 +00:00
}
/* Check IIR_TXRDY clear ? */
result = 0;
if (failures[6] & IIR_TXRDY) {
/* Nop, Double check with clearing IER */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_ier, 0);
if (sio_getreg(com, com_iir) & IIR_NOPEND) {
Argh, don't turn the IIR test on unless it's a pccard. These tests mess up the subsequent probes.
1999-11-18 10:29:06 +00:00
/* Ok. we're familia this gang */
SET_FLAG(dev, COM_C_IIR_TXRDYBUG);
} else {
/* Unknown, Just omit this chip.. XXX */
result = ENXIO;
}
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
} else {
Argh, don't turn the IIR test on unless it's a pccard. These tests mess up the subsequent probes.
1999-11-18 10:29:06 +00:00
/* OK. this is well-known guys */
CLR_FLAG(dev, COM_C_IIR_TXRDYBUG);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, CFCR_8BITS);
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
enable_intr();
bus_release_resource(dev, SYS_RES_IOPORT, rid, port);
return (iobase == siocniobase ? 0 : result);
}
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* Check that
* o the CFCR, IER and MCR in UART hold the values written to them
* (the values happen to be all distinct - this is good for
* avoiding false positive tests from bus echoes).
* o an output interrupt is generated and its vector is correct.
* o the interrupt goes away when the IIR in the UART is read.
*/
/* EXTRA DELAY? */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
failures[0] = sio_getreg(com, com_cfcr) - CFCR_8BITS;
failures[1] = sio_getreg(com, com_ier) - IER_ETXRDY;
failures[2] = sio_getreg(com, com_mcr) - mcr_image;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY(10000); /* Some internal modems need this time */
irqmap[1] = isa_irq_pending();
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
failures[4] = (sio_getreg(com, com_iir) & IIR_IMASK) - IIR_TXRDY;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY(1000); /* XXX */
irqmap[2] = isa_irq_pending();
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
failures[6] = (sio_getreg(com, com_iir) & IIR_IMASK) - IIR_NOPEND;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* Turn off all device interrupts and check that they go off properly.
* Leave MCR_IENABLE alone. For ports without a master port, it gates
* the OUT2 output of the UART to
* the ICU input. Closing the gate would give a floating ICU input
* (unless there is another device driving it) and spurious interrupts.
* (On the system that this was first tested on, the input floats high
* and gives a (masked) interrupt as soon as the gate is closed.)
*/
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_ier, 0);
sio_setreg(com, com_cfcr, CFCR_8BITS); /* dummy to avoid bus echo */
failures[7] = sio_getreg(com, com_ier);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY(1000); /* XXX */
irqmap[3] = isa_irq_pending();
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
failures[9] = (sio_getreg(com, com_iir) & IIR_IMASK) - IIR_NOPEND;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
enable_intr();
irqs = irqmap[1] & ~irqmap[0];
Use bus_get_resource() instead of bus_get_resource_start() as the latter returns "0" on failure, which is indistinguishable from (say) irq 0. This should stop a couple of stray messages that turn up. Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to a normal interrupt. This might help pccard folks with a shared slot interrupt. This whole thing needs to be revisited.
1999-12-06 06:47:02 +00:00
if (bus_get_resource(idev, SYS_RES_IRQ, 0, &xirq, NULL) == 0 &&
((1 << xirq) & irqs) == 0)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
printf(
Fix a pair of silly warnings that I introduced (that would have been nasty on an Alpha or some other sizeof(int) != sizeof(long) machine).
1999-12-06 17:52:20 +00:00
"sio%d: configured irq %ld not in bitmap of probed irqs %#x\n",
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
device_get_unit(dev), xirq, irqs);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (bootverbose)
printf("sio%d: irq maps: %#x %#x %#x %#x\n",
device_get_unit(dev),
irqmap[0], irqmap[1], irqmap[2], irqmap[3]);
result = 0;
for (fn = 0; fn < sizeof failures; ++fn)
if (failures[fn]) {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_mcr, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
result = ENXIO;
if (bootverbose) {
printf("sio%d: probe failed test(s):",
device_get_unit(dev));
for (fn = 0; fn < sizeof failures; ++fn)
if (failures[fn])
printf(" %d", fn);
printf("\n");
}
break;
}
bus_release_resource(dev, SYS_RES_IOPORT, rid, port);
return (iobase == siocniobase ? 0 : result);
}
#ifdef COM_ESP
static int
espattach(com, esp_port)
struct com_s *com;
Port_t esp_port;
{
u_char dips;
u_char val;
/*
* Check the ESP-specific I/O port to see if we're an ESP
* card. If not, return failure immediately.
*/
if ((inb(esp_port) & 0xf3) == 0) {
printf(" port 0x%x is not an ESP board?\n", esp_port);
return (0);
}
/*
* We've got something that claims to be a Hayes ESP card.
* Let's hope so.
*/
/* Get the dip-switch configuration */
outb(esp_port + ESP_CMD1, ESP_GETDIPS);
dips = inb(esp_port + ESP_STATUS1);
/*
* Bits 0,1 of dips say which COM port we are.
*/
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
if (rman_get_start(com->ioportres) == likely_com_ports[dips & 0x03])
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
printf(" : ESP");
else {
printf(" esp_port has com %d\n", dips & 0x03);
return (0);
}
/*
* Check for ESP version 2.0 or later: bits 4,5,6 = 010.
*/
outb(esp_port + ESP_CMD1, ESP_GETTEST);
val = inb(esp_port + ESP_STATUS1); /* clear reg 1 */
val = inb(esp_port + ESP_STATUS2);
if ((val & 0x70) < 0x20) {
printf("-old (%o)", val & 0x70);
return (0);
}
/*
* Check for ability to emulate 16550: bit 7 == 1
*/
if ((dips & 0x80) == 0) {
printf(" slave");
return (0);
}
/*
* Okay, we seem to be a Hayes ESP card. Whee.
*/
com->esp = TRUE;
com->esp_port = esp_port;
return (1);
}
#endif /* COM_ESP */
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
static int
sio_isa_attach(dev)
device_t dev;
{
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
return (sioattach(dev, 0));
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
}
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
static int
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
sioattach(dev, xrid)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
device_t dev;
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
int xrid;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{
struct com_s *com;
#ifdef COM_ESP
Port_t *espp;
#endif
Port_t iobase;
int unit;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
u_int flags;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
int rid;
struct resource *port;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
int ret;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
rid = xrid;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
port = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid,
0, ~0, IO_COMSIZE, RF_ACTIVE);
if (!port)
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
return (ENXIO);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
iobase = rman_get_start(port);
unit = device_get_unit(dev);
com = device_get_softc(dev);
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
flags = device_get_flags(dev);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
if (unit >= sio_numunits)
sio_numunits = unit + 1;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* sioprobe() has initialized the device registers as follows:
* o cfcr = CFCR_8BITS.
* It is most important that CFCR_DLAB is off, so that the
* data port is not hidden when we enable interrupts.
* o ier = 0.
* Interrupts are only enabled when the line is open.
* o mcr = MCR_IENABLE, or 0 if the port has AST/4 compatible
* interrupt control register or the config specifies no irq.
* Keeping MCR_DTR and MCR_RTS off might stop the external
* device from sending before we are ready.
*/
bzero(com, sizeof *com);
com->unit = unit;
com->ioportres = port;
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
com->bst = rman_get_bustag(port);
com->bsh = rman_get_bushandle(port);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com->cfcr_image = CFCR_8BITS;
com->dtr_wait = 3 * hz;
com->loses_outints = COM_LOSESOUTINTS(flags) != 0;
Fixed regressions in rev.1.274: 1) Non-AST4 multiport cards were broken by bypassing the code that changes `idev' to the multiport master device. 2) AST4 multiport cards apparently were broken by inverting the test for the master device having an irq. 3) Error handling for nonexistent master devices was broken by removing a check for a null pointer. 4) `int' error codes returned by bus_get_resource() were assigned directly to the boolean variable com->no_irq. Probably harmless, since the boolean is implemented as a u_char. Submitted by: part 1) by Chris Radek <cradek@in221.inetnebr.com> part 2) by yokota Approved by: jkh
2000-02-15 17:29:09 +00:00
com->no_irq = bus_get_resource(dev, SYS_RES_IRQ, 0, NULL, NULL) != 0;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com->tx_fifo_size = 1;
com->obufs[0].l_head = com->obuf1;
com->obufs[1].l_head = com->obuf2;
com->data_port = iobase + com_data;
com->int_id_port = iobase + com_iir;
com->modem_ctl_port = iobase + com_mcr;
com->mcr_image = inb(com->modem_ctl_port);
com->line_status_port = iobase + com_lsr;
com->modem_status_port = iobase + com_msr;
com->intr_ctl_port = iobase + com_ier;
/*
* We don't use all the flags from <sys/ttydefaults.h> since they
* are only relevant for logins. It's important to have echo off
* initially so that the line doesn't start blathering before the
* echo flag can be turned off.
*/
com->it_in.c_iflag = 0;
com->it_in.c_oflag = 0;
com->it_in.c_cflag = TTYDEF_CFLAG;
com->it_in.c_lflag = 0;
if (unit == comconsole) {
com->it_in.c_iflag = TTYDEF_IFLAG;
com->it_in.c_oflag = TTYDEF_OFLAG;
com->it_in.c_cflag = TTYDEF_CFLAG | CLOCAL;
com->it_in.c_lflag = TTYDEF_LFLAG;
com->lt_out.c_cflag = com->lt_in.c_cflag = CLOCAL;
com->lt_out.c_ispeed = com->lt_out.c_ospeed =
com->lt_in.c_ispeed = com->lt_in.c_ospeed =
com->it_in.c_ispeed = com->it_in.c_ospeed = comdefaultrate;
} else
com->it_in.c_ispeed = com->it_in.c_ospeed = TTYDEF_SPEED;
if (siosetwater(com, com->it_in.c_ispeed) != 0) {
enable_intr();
"Completed" the previous fix. Return ENOMEM on memory allocation failure in sioattach(), not ENXIO. Free resources before returning early in sioprobe() and sioattach().
2000-01-29 03:02:55 +00:00
/*
* Leave i/o resources allocated if this is a `cn'-level
* console, so that other devices can't snarf them.
*/
if (iobase != siocniobase)
bus_release_resource(dev, SYS_RES_IOPORT, rid, port);
return (ENOMEM);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
enable_intr();
termioschars(&com->it_in);
com->it_out = com->it_in;
/* attempt to determine UART type */
printf("sio%d: type", unit);
#ifdef COM_MULTIPORT
if (!COM_ISMULTIPORT(flags) && !COM_IIR_TXRDYBUG(flags))
#else
if (!COM_IIR_TXRDYBUG(flags))
#endif
{
u_char scr;
u_char scr1;
u_char scr2;
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
scr = sio_getreg(com, com_scr);
sio_setreg(com, com_scr, 0xa5);
scr1 = sio_getreg(com, com_scr);
sio_setreg(com, com_scr, 0x5a);
scr2 = sio_getreg(com, com_scr);
sio_setreg(com, com_scr, scr);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (scr1 != 0xa5 || scr2 != 0x5a) {
printf(" 8250");
goto determined_type;
}
}
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo, FIFO_ENABLE | FIFO_RX_HIGH);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY(100);
com->st16650a = 0;
switch (inb(com->int_id_port) & IIR_FIFO_MASK) {
case FIFO_RX_LOW:
printf(" 16450");
break;
case FIFO_RX_MEDL:
printf(" 16450?");
break;
case FIFO_RX_MEDH:
printf(" 16550?");
break;
case FIFO_RX_HIGH:
if (COM_NOFIFO(flags)) {
printf(" 16550A fifo disabled");
} else {
com->hasfifo = TRUE;
if (COM_ST16650A(flags)) {
com->st16650a = 1;
com->tx_fifo_size = 32;
printf(" ST16650A");
} else {
com->tx_fifo_size = COM_FIFOSIZE(flags);
printf(" 16550A");
}
}
#ifdef COM_ESP
for (espp = likely_esp_ports; *espp != 0; espp++)
if (espattach(com, *espp)) {
com->tx_fifo_size = 1024;
break;
}
#endif
if (!com->st16650a) {
if (!com->tx_fifo_size)
com->tx_fifo_size = 16;
else
printf(" lookalike with %d bytes FIFO",
com->tx_fifo_size);
}
break;
}
#ifdef COM_ESP
if (com->esp) {
/*
* Set 16550 compatibility mode.
* We don't use the ESP_MODE_SCALE bit to increase the
* fifo trigger levels because we can't handle large
* bursts of input.
* XXX flow control should be set in comparam(), not here.
*/
outb(com->esp_port + ESP_CMD1, ESP_SETMODE);
outb(com->esp_port + ESP_CMD2, ESP_MODE_RTS | ESP_MODE_FIFO);
/* Set RTS/CTS flow control. */
outb(com->esp_port + ESP_CMD1, ESP_SETFLOWTYPE);
outb(com->esp_port + ESP_CMD2, ESP_FLOW_RTS);
outb(com->esp_port + ESP_CMD2, ESP_FLOW_CTS);
/* Set flow-control levels. */
outb(com->esp_port + ESP_CMD1, ESP_SETRXFLOW);
outb(com->esp_port + ESP_CMD2, HIBYTE(768));
outb(com->esp_port + ESP_CMD2, LOBYTE(768));
outb(com->esp_port + ESP_CMD2, HIBYTE(512));
outb(com->esp_port + ESP_CMD2, LOBYTE(512));
}
#endif /* COM_ESP */
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
determined_type: ;
#ifdef COM_MULTIPORT
if (COM_ISMULTIPORT(flags)) {
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
device_t masterdev;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com->multiport = TRUE;
printf(" (multiport");
if (unit == COM_MPMASTER(flags))
printf(" master");
printf(")");
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
masterdev = devclass_get_device(sio_devclass,
COM_MPMASTER(flags));
Fixed regressions in rev.1.274: 1) Non-AST4 multiport cards were broken by bypassing the code that changes `idev' to the multiport master device. 2) AST4 multiport cards apparently were broken by inverting the test for the master device having an irq. 3) Error handling for nonexistent master devices was broken by removing a check for a null pointer. 4) `int' error codes returned by bus_get_resource() were assigned directly to the boolean variable com->no_irq. Probably harmless, since the boolean is implemented as a u_char. Submitted by: part 1) by Chris Radek <cradek@in221.inetnebr.com> part 2) by yokota Approved by: jkh
2000-02-15 17:29:09 +00:00
com->no_irq = (masterdev == NULL || bus_get_resource(masterdev,
SYS_RES_IRQ, 0, NULL, NULL) != 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
#endif /* COM_MULTIPORT */
if (unit == comconsole)
printf(", console");
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
if (COM_IIR_TXRDYBUG(flags))
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
printf(" with a bogus IIR_TXRDY register");
printf("\n");
if (!sio_registered) {
register_swi(SWI_TTY, siopoll);
sio_registered = TRUE;
}
make_dev(&sio_cdevsw, unit,
UID_ROOT, GID_WHEEL, 0600, "ttyd%r", unit);
make_dev(&sio_cdevsw, unit | CONTROL_INIT_STATE,
UID_ROOT, GID_WHEEL, 0600, "ttyid%r", unit);
make_dev(&sio_cdevsw, unit | CONTROL_LOCK_STATE,
UID_ROOT, GID_WHEEL, 0600, "ttyld%r", unit);
make_dev(&sio_cdevsw, unit | CALLOUT_MASK,
UID_UUCP, GID_DIALER, 0660, "cuaa%r", unit);
make_dev(&sio_cdevsw, unit | CALLOUT_MASK | CONTROL_INIT_STATE,
UID_UUCP, GID_DIALER, 0660, "cuaia%r", unit);
make_dev(&sio_cdevsw, unit | CALLOUT_MASK | CONTROL_LOCK_STATE,
UID_UUCP, GID_DIALER, 0660, "cuala%r", unit);
com->flags = flags;
com->pps.ppscap = PPS_CAPTUREASSERT | PPS_CAPTURECLEAR;
pps_init(&com->pps);
rid = 0;
com->irqres = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0ul, ~0ul, 1,
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
RF_ACTIVE);
if (com->irqres) {
ret = BUS_SETUP_INTR(device_get_parent(dev), dev, com->irqres,
Use bus_get_resource() instead of bus_get_resource_start() as the latter returns "0" on failure, which is indistinguishable from (say) irq 0. This should stop a couple of stray messages that turn up. Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to a normal interrupt. This might help pccard folks with a shared slot interrupt. This whole thing needs to be revisited.
1999-12-06 06:47:02 +00:00
INTR_TYPE_TTY | INTR_TYPE_FAST,
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
siointr, com, &com->cookie);
Use bus_get_resource() instead of bus_get_resource_start() as the latter returns "0" on failure, which is indistinguishable from (say) irq 0. This should stop a couple of stray messages that turn up. Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to a normal interrupt. This might help pccard folks with a shared slot interrupt. This whole thing needs to be revisited.
1999-12-06 06:47:02 +00:00
if (ret) {
ret = BUS_SETUP_INTR(device_get_parent(dev), dev,
com->irqres, INTR_TYPE_TTY,
o Make pccard work at all by including card.h o fix return type of sio_pccard_detach o don't free softc in deatch, since that is done by newbus o disconnect interrupt we used to have. Add cookie to com so that we can tear down the interrupt on unload o Set gone earlier, but likely doesn't matter This makes sio pccards work again. Cards that are active when ejects may not work (but they might, softc goes away quickly). These changes are unreviewed by bde. I'll make any style changes he wants.
1999-12-10 08:19:19 +00:00
siointr, com, &com->cookie);
Use bus_get_resource() instead of bus_get_resource_start() as the latter returns "0" on failure, which is indistinguishable from (say) irq 0. This should stop a couple of stray messages that turn up. Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to a normal interrupt. This might help pccard folks with a shared slot interrupt. This whole thing needs to be revisited.
1999-12-06 06:47:02 +00:00
if (ret == 0)
device_printf(dev, "unable to activate interrupt in fast mode - using normal mode");
}
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
if (ret)
device_printf(dev, "could not activate interrupt\n");
}
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return (0);
}
static int
sioopen(dev, flag, mode, p)
dev_t dev;
int flag;
int mode;
struct proc *p;
{
struct com_s *com;
int error;
int mynor;
int s;
struct tty *tp;
int unit;
mynor = minor(dev);
unit = MINOR_TO_UNIT(mynor);
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
com = com_addr(unit);
if (com == NULL)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return (ENXIO);
if (com->gone)
return (ENXIO);
if (mynor & CONTROL_MASK)
return (0);
tp = dev->si_tty = com->tp = ttymalloc(com->tp);
s = spltty();
/*
* We jump to this label after all non-interrupted sleeps to pick
* up any changes of the device state.
*/
open_top:
while (com->state & CS_DTR_OFF) {
error = tsleep(&com->dtr_wait, TTIPRI | PCATCH, "siodtr", 0);
if (com_addr(unit) == NULL)
return (ENXIO);
if (error != 0 || com->gone)
goto out;
}
if (tp->t_state & TS_ISOPEN) {
/*
* The device is open, so everything has been initialized.
* Handle conflicts.
*/
if (mynor & CALLOUT_MASK) {
if (!com->active_out) {
error = EBUSY;
goto out;
}
} else {
if (com->active_out) {
if (flag & O_NONBLOCK) {
error = EBUSY;
goto out;
}
error = tsleep(&com->active_out,
TTIPRI | PCATCH, "siobi", 0);
if (com_addr(unit) == NULL)
return (ENXIO);
if (error != 0 || com->gone)
goto out;
goto open_top;
}
}
if (tp->t_state & TS_XCLUDE &&
suser(p)) {
error = EBUSY;
goto out;
}
} else {
/*
* The device isn't open, so there are no conflicts.
* Initialize it. Initialization is done twice in many
* cases: to preempt sleeping callin opens if we are
* callout, and to complete a callin open after DCD rises.
*/
tp->t_oproc = comstart;
tp->t_param = comparam;
This patch clears the way for removing a number of tty related fields in struct cdevsw: d_stop moved to struct tty. d_reset already unused. d_devtotty linkage now provided by dev_t->si_tty. These fields will be removed from struct cdevsw together with d_params and d_maxio Real Soon Now. The changes in this patch consist of: initialize dev->si_tty in *_open() initialize tty->t_stop remove devtotty functions rename ttpoll to ttypoll a few adjustments to these changes in the generic code a bump of __FreeBSD_version add a couple of FreeBSD tags
1999-09-25 16:21:39 +00:00
tp->t_stop = comstop;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
tp->t_dev = dev;
tp->t_termios = mynor & CALLOUT_MASK
? com->it_out : com->it_in;
(void)commctl(com, TIOCM_DTR | TIOCM_RTS, DMSET);
com->poll = com->no_irq;
com->poll_output = com->loses_outints;
++com->wopeners;
error = comparam(tp, &tp->t_termios);
--com->wopeners;
if (error != 0)
goto out;
/*
* XXX we should goto open_top if comparam() slept.
*/
if (com->hasfifo) {
/*
* (Re)enable and drain fifos.
*
* Certain SMC chips cause problems if the fifos
* are enabled while input is ready. Turn off the
* fifo if necessary to clear the input. We test
* the input ready bit after enabling the fifos
* since we've already enabled them in comparam()
* and to handle races between enabling and fresh
* input.
*/
while (TRUE) {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo,
FIFO_RCV_RST | FIFO_XMT_RST
| com->fifo_image);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* XXX the delays are for superstitious
* historical reasons. It must be less than
* the character time at the maximum
* supported speed (87 usec at 115200 bps
* 8N1). Otherwise we might loop endlessly
* if data is streaming in. We used to use
* delays of 100. That usually worked
* because DELAY(100) used to usually delay
* for about 85 usec instead of 100.
*/
DELAY(50);
if (!(inb(com->line_status_port) & LSR_RXRDY))
break;
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
DELAY(50);
(void) inb(com->data_port);
}
}
disable_intr();
(void) inb(com->line_status_port);
(void) inb(com->data_port);
com->prev_modem_status = com->last_modem_status
= inb(com->modem_status_port);
if (COM_IIR_TXRDYBUG(com->flags)) {
outb(com->intr_ctl_port, IER_ERXRDY | IER_ERLS
| IER_EMSC);
} else {
outb(com->intr_ctl_port, IER_ERXRDY | IER_ETXRDY
| IER_ERLS | IER_EMSC);
}
enable_intr();
/*
* Handle initial DCD. Callout devices get a fake initial
* DCD (trapdoor DCD). If we are callout, then any sleeping
* callin opens get woken up and resume sleeping on "siobi"
* instead of "siodcd".
*/
/*
* XXX `mynor & CALLOUT_MASK' should be
* `tp->t_cflag & (SOFT_CARRIER | TRAPDOOR_CARRIER) where
* TRAPDOOR_CARRIER is the default initial state for callout
* devices and SOFT_CARRIER is like CLOCAL except it hides
* the true carrier.
*/
if (com->prev_modem_status & MSR_DCD || mynor & CALLOUT_MASK)
(*linesw[tp->t_line].l_modem)(tp, 1);
}
/*
* Wait for DCD if necessary.
*/
if (!(tp->t_state & TS_CARR_ON) && !(mynor & CALLOUT_MASK)
&& !(tp->t_cflag & CLOCAL) && !(flag & O_NONBLOCK)) {
++com->wopeners;
error = tsleep(TSA_CARR_ON(tp), TTIPRI | PCATCH, "siodcd", 0);
if (com_addr(unit) == NULL)
return (ENXIO);
--com->wopeners;
if (error != 0 || com->gone)
goto out;
goto open_top;
}
error = (*linesw[tp->t_line].l_open)(dev, tp);
disc_optim(tp, &tp->t_termios, com);
if (tp->t_state & TS_ISOPEN && mynor & CALLOUT_MASK)
com->active_out = TRUE;
siosettimeout();
out:
splx(s);
if (!(tp->t_state & TS_ISOPEN) && com->wopeners == 0)
comhardclose(com);
return (error);
}
static int
sioclose(dev, flag, mode, p)
dev_t dev;
int flag;
int mode;
struct proc *p;
{
struct com_s *com;
int mynor;
int s;
struct tty *tp;
mynor = minor(dev);
if (mynor & CONTROL_MASK)
return (0);
com = com_addr(MINOR_TO_UNIT(mynor));
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL)
return (ENODEV);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
tp = com->tp;
s = spltty();
(*linesw[tp->t_line].l_close)(tp, flag);
disc_optim(tp, &tp->t_termios, com);
This patch clears the way for removing a number of tty related fields in struct cdevsw: d_stop moved to struct tty. d_reset already unused. d_devtotty linkage now provided by dev_t->si_tty. These fields will be removed from struct cdevsw together with d_params and d_maxio Real Soon Now. The changes in this patch consist of: initialize dev->si_tty in *_open() initialize tty->t_stop remove devtotty functions rename ttpoll to ttypoll a few adjustments to these changes in the generic code a bump of __FreeBSD_version add a couple of FreeBSD tags
1999-09-25 16:21:39 +00:00
comstop(tp, FREAD | FWRITE);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
comhardclose(com);
ttyclose(tp);
siosettimeout();
splx(s);
if (com->gone) {
printf("sio%d: gone\n", com->unit);
s = spltty();
if (com->ibuf != NULL)
free(com->ibuf, M_DEVBUF);
bzero(tp, sizeof *tp);
splx(s);
}
return (0);
}
static void
comhardclose(com)
struct com_s *com;
{
int s;
struct tty *tp;
int unit;
unit = com->unit;
s = spltty();
com->poll = FALSE;
com->poll_output = FALSE;
com->do_timestamp = FALSE;
com->do_dcd_timestamp = FALSE;
com->pps.ppsparam.mode = 0;
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, com->cfcr_image &= ~CFCR_SBREAK);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
{
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_ier, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
tp = com->tp;
if (tp->t_cflag & HUPCL
/*
* XXX we will miss any carrier drop between here and the
* next open. Perhaps we should watch DCD even when the
* port is closed; it is not sufficient to check it at
* the next open because it might go up and down while
* we're not watching.
*/
|| (!com->active_out
&& !(com->prev_modem_status & MSR_DCD)
&& !(com->it_in.c_cflag & CLOCAL))
|| !(tp->t_state & TS_ISOPEN)) {
(void)commctl(com, TIOCM_DTR, DMBIC);
if (com->dtr_wait != 0 && !(com->state & CS_DTR_OFF)) {
timeout(siodtrwakeup, com, com->dtr_wait);
com->state |= CS_DTR_OFF;
}
}
}
if (com->hasfifo) {
/*
* Disable fifos so that they are off after controlled
* reboots. Some BIOSes fail to detect 16550s when the
* fifos are enabled.
*/
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo, 0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
com->active_out = FALSE;
wakeup(&com->active_out);
wakeup(TSA_CARR_ON(tp)); /* restart any wopeners */
splx(s);
}
static int
sioread(dev, uio, flag)
dev_t dev;
struct uio *uio;
int flag;
{
int mynor;
struct com_s *com;
mynor = minor(dev);
if (mynor & CONTROL_MASK)
return (ENODEV);
com = com_addr(MINOR_TO_UNIT(mynor));
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL || com->gone)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return (ENODEV);
return ((*linesw[com->tp->t_line].l_read)(com->tp, uio, flag));
}
static int
siowrite(dev, uio, flag)
dev_t dev;
struct uio *uio;
int flag;
{
int mynor;
struct com_s *com;
int unit;
mynor = minor(dev);
if (mynor & CONTROL_MASK)
return (ENODEV);
unit = MINOR_TO_UNIT(mynor);
com = com_addr(unit);
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL || com->gone)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return (ENODEV);
/*
* (XXX) We disallow virtual consoles if the physical console is
* a serial port. This is in case there is a display attached that
* is not the console. In that situation we don't need/want the X
* server taking over the console.
*/
if (constty != NULL && unit == comconsole)
constty = NULL;
return ((*linesw[com->tp->t_line].l_write)(com->tp, uio, flag));
}
static void
siobusycheck(chan)
void *chan;
{
struct com_s *com;
int s;
com = (struct com_s *)chan;
/*
* Clear TS_BUSY if low-level output is complete.
* spl locking is sufficient because siointr1() does not set CS_BUSY.
* If siointr1() clears CS_BUSY after we look at it, then we'll get
* called again. Reading the line status port outside of siointr1()
* is safe because CS_BUSY is clear so there are no output interrupts
* to lose.
*/
s = spltty();
if (com->state & CS_BUSY)
com->extra_state &= ~CSE_BUSYCHECK; /* False alarm. */
else if ((inb(com->line_status_port) & (LSR_TSRE | LSR_TXRDY))
== (LSR_TSRE | LSR_TXRDY)) {
com->tp->t_state &= ~TS_BUSY;
ttwwakeup(com->tp);
com->extra_state &= ~CSE_BUSYCHECK;
} else
timeout(siobusycheck, com, hz / 100);
splx(s);
}
static void
siodtrwakeup(chan)
void *chan;
{
struct com_s *com;
com = (struct com_s *)chan;
com->state &= ~CS_DTR_OFF;
wakeup(&com->dtr_wait);
}
static void
sioinput(com)
struct com_s *com;
{
u_char *buf;
int incc;
u_char line_status;
int recv_data;
struct tty *tp;
buf = com->ibuf;
tp = com->tp;
if (!(tp->t_state & TS_ISOPEN) || !(tp->t_cflag & CREAD)) {
com_events -= (com->iptr - com->ibuf);
com->iptr = com->ibuf;
return;
}
if (tp->t_state & TS_CAN_BYPASS_L_RINT) {
/*
* Avoid the grotesquely inefficient lineswitch routine
* (ttyinput) in "raw" mode. It usually takes about 450
* instructions (that's without canonical processing or echo!).
* slinput is reasonably fast (usually 40 instructions plus
* call overhead).
*/
do {
enable_intr();
incc = com->iptr - buf;
if (tp->t_rawq.c_cc + incc > tp->t_ihiwat
&& (com->state & CS_RTS_IFLOW
|| tp->t_iflag & IXOFF)
&& !(tp->t_state & TS_TBLOCK))
ttyblock(tp);
com->delta_error_counts[CE_TTY_BUF_OVERFLOW]
+= b_to_q((char *)buf, incc, &tp->t_rawq);
buf += incc;
tk_nin += incc;
tk_rawcc += incc;
tp->t_rawcc += incc;
ttwakeup(tp);
if (tp->t_state & TS_TTSTOP
&& (tp->t_iflag & IXANY
|| tp->t_cc[VSTART] == tp->t_cc[VSTOP])) {
tp->t_state &= ~TS_TTSTOP;
tp->t_lflag &= ~FLUSHO;
comstart(tp);
}
disable_intr();
} while (buf < com->iptr);
} else {
do {
enable_intr();
line_status = buf[com->ierroff];
recv_data = *buf++;
if (line_status
& (LSR_BI | LSR_FE | LSR_OE | LSR_PE)) {
if (line_status & LSR_BI)
recv_data |= TTY_BI;
if (line_status & LSR_FE)
recv_data |= TTY_FE;
if (line_status & LSR_OE)
recv_data |= TTY_OE;
if (line_status & LSR_PE)
recv_data |= TTY_PE;
}
(*linesw[tp->t_line].l_rint)(recv_data, tp);
disable_intr();
} while (buf < com->iptr);
}
com_events -= (com->iptr - com->ibuf);
com->iptr = com->ibuf;
/*
* There is now room for another low-level buffer full of input,
* so enable RTS if it is now disabled and there is room in the
* high-level buffer.
*/
if ((com->state & CS_RTS_IFLOW) && !(com->mcr_image & MCR_RTS) &&
!(tp->t_state & TS_TBLOCK))
outb(com->modem_ctl_port, com->mcr_image |= MCR_RTS);
}
void
siointr(arg)
void *arg;
{
#ifndef COM_MULTIPORT
COM_LOCK();
siointr1((struct com_s *) arg);
COM_UNLOCK();
#else /* COM_MULTIPORT */
bool_t possibly_more_intrs;
int unit;
struct com_s *com;
/*
* Loop until there is no activity on any port. This is necessary
* to get an interrupt edge more than to avoid another interrupt.
* If the IRQ signal is just an OR of the IRQ signals from several
* devices, then the edge from one may be lost because another is
* on.
*/
COM_LOCK();
do {
possibly_more_intrs = FALSE;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
for (unit = 0; unit < sio_numunits; ++unit) {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com = com_addr(unit);
/*
* XXX COM_LOCK();
* would it work here, or be counter-productive?
*/
if (com != NULL
&& !com->gone
&& (inb(com->int_id_port) & IIR_IMASK)
!= IIR_NOPEND) {
siointr1(com);
possibly_more_intrs = TRUE;
}
/* XXX COM_UNLOCK(); */
}
} while (possibly_more_intrs);
COM_UNLOCK();
#endif /* COM_MULTIPORT */
}
static void
siointr1(com)
struct com_s *com;
{
u_char line_status;
u_char modem_status;
u_char *ioptr;
u_char recv_data;
u_char int_ctl;
u_char int_ctl_new;
struct timecounter *tc;
u_int count;
int_ctl = inb(com->intr_ctl_port);
int_ctl_new = int_ctl;
while (!com->gone) {
if (com->pps.ppsparam.mode & PPS_CAPTUREBOTH) {
modem_status = inb(com->modem_status_port);
if ((modem_status ^ com->last_modem_status) & MSR_DCD) {
tc = timecounter;
count = tc->tc_get_timecount(tc);
pps_event(&com->pps, tc, count,
(modem_status & MSR_DCD) ?
PPS_CAPTUREASSERT : PPS_CAPTURECLEAR);
}
}
line_status = inb(com->line_status_port);
/* input event? (check first to help avoid overruns) */
while (line_status & LSR_RCV_MASK) {
/* break/unnattached error bits or real input? */
if (!(line_status & LSR_RXRDY))
recv_data = 0;
else
recv_data = inb(com->data_port);
Add option ALT_BREAK_TO_DEBUGGER. Implement the Solaris way to break into DDB over a serial console instead of sending a break. Sending the character sequence CR ~ ^b will break the kernel into DDB (if DDB is enabled). Reviewed by: peter
2000-06-14 06:41:33 +00:00
#if defined(DDB) && defined(ALT_BREAK_TO_DEBUGGER)
/*
* Solaris implements a new BREAK which is initiated
* by a character sequence CR ~ ^b which is similar
* to a familiar pattern used on Sun servers by the
* Remote Console.
*/
#define KEY_CRTLB 2 /* ^B */
#define KEY_CR 13 /* CR '\r' */
#define KEY_TILDE 126 /* ~ */
if (com->unit == comconsole) {
static int brk_state1 = 0, brk_state2 = 0;
if (recv_data == KEY_CR) {
brk_state1 = recv_data;
brk_state2 = 0;
} else if (brk_state1 == KEY_CR && (recv_data == KEY_TILDE || recv_data == KEY_CRTLB)) {
if (recv_data == KEY_TILDE)
brk_state2 = recv_data;
else if (brk_state2 == KEY_TILDE && recv_data == KEY_CRTLB) {
breakpoint();
brk_state1 = brk_state2 = 0;
goto cont;
} else
brk_state2 = 0;
} else
brk_state1 = 0;
}
#endif
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (line_status & (LSR_BI | LSR_FE | LSR_PE)) {
/*
* Don't store BI if IGNBRK or FE/PE if IGNPAR.
* Otherwise, push the work to a higher level
* (to handle PARMRK) if we're bypassing.
* Otherwise, convert BI/FE and PE+INPCK to 0.
*
* This makes bypassing work right in the
* usual "raw" case (IGNBRK set, and IGNPAR
* and INPCK clear).
*
* Note: BI together with FE/PE means just BI.
*/
if (line_status & LSR_BI) {
#if defined(DDB) && defined(BREAK_TO_DEBUGGER)
if (com->unit == comconsole) {
breakpoint();
goto cont;
}
#endif
if (com->tp == NULL
|| com->tp->t_iflag & IGNBRK)
goto cont;
} else {
if (com->tp == NULL
|| com->tp->t_iflag & IGNPAR)
goto cont;
}
if (com->tp->t_state & TS_CAN_BYPASS_L_RINT
&& (line_status & (LSR_BI | LSR_FE)
|| com->tp->t_iflag & INPCK))
recv_data = 0;
}
++com->bytes_in;
if (com->hotchar != 0 && recv_data == com->hotchar)
setsofttty();
ioptr = com->iptr;
if (ioptr >= com->ibufend)
CE_RECORD(com, CE_INTERRUPT_BUF_OVERFLOW);
else {
if (com->do_timestamp)
microtime(&com->timestamp);
++com_events;
schedsofttty();
#if 0 /* for testing input latency vs efficiency */
if (com->iptr - com->ibuf == 8)
setsofttty();
#endif
ioptr[0] = recv_data;
ioptr[com->ierroff] = line_status;
com->iptr = ++ioptr;
if (ioptr == com->ihighwater
&& com->state & CS_RTS_IFLOW)
outb(com->modem_ctl_port,
com->mcr_image &= ~MCR_RTS);
if (line_status & LSR_OE)
CE_RECORD(com, CE_OVERRUN);
}
cont:
/*
* "& 0x7F" is to avoid the gcc-1.40 generating a slow
* jump from the top of the loop to here
*/
line_status = inb(com->line_status_port) & 0x7F;
}
/* modem status change? (always check before doing output) */
modem_status = inb(com->modem_status_port);
if (modem_status != com->last_modem_status) {
if (com->do_dcd_timestamp
&& !(com->last_modem_status & MSR_DCD)
&& modem_status & MSR_DCD)
microtime(&com->dcd_timestamp);
/*
* Schedule high level to handle DCD changes. Note
* that we don't use the delta bits anywhere. Some
* UARTs mess them up, and it's easy to remember the
* previous bits and calculate the delta.
*/
com->last_modem_status = modem_status;
if (!(com->state & CS_CHECKMSR)) {
com_events += LOTS_OF_EVENTS;
com->state |= CS_CHECKMSR;
setsofttty();
}
/* handle CTS change immediately for crisp flow ctl */
if (com->state & CS_CTS_OFLOW) {
if (modem_status & MSR_CTS)
com->state |= CS_ODEVREADY;
else
com->state &= ~CS_ODEVREADY;
}
}
/* output queued and everything ready? */
if (line_status & LSR_TXRDY
&& com->state >= (CS_BUSY | CS_TTGO | CS_ODEVREADY)) {
ioptr = com->obufq.l_head;
if (com->tx_fifo_size > 1) {
u_int ocount;
ocount = com->obufq.l_tail - ioptr;
if (ocount > com->tx_fifo_size)
ocount = com->tx_fifo_size;
com->bytes_out += ocount;
do
outb(com->data_port, *ioptr++);
while (--ocount != 0);
} else {
outb(com->data_port, *ioptr++);
++com->bytes_out;
}
com->obufq.l_head = ioptr;
if (COM_IIR_TXRDYBUG(com->flags)) {
int_ctl_new = int_ctl | IER_ETXRDY;
}
if (ioptr >= com->obufq.l_tail) {
struct lbq *qp;
qp = com->obufq.l_next;
qp->l_queued = FALSE;
qp = qp->l_next;
if (qp != NULL) {
com->obufq.l_head = qp->l_head;
com->obufq.l_tail = qp->l_tail;
com->obufq.l_next = qp;
} else {
/* output just completed */
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
if (COM_IIR_TXRDYBUG(com->flags)) {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
int_ctl_new = int_ctl & ~IER_ETXRDY;
}
com->state &= ~CS_BUSY;
}
if (!(com->state & CS_ODONE)) {
com_events += LOTS_OF_EVENTS;
com->state |= CS_ODONE;
setsofttty(); /* handle at high level ASAP */
}
}
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
if (COM_IIR_TXRDYBUG(com->flags) && (int_ctl != int_ctl_new)) {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
outb(com->intr_ctl_port, int_ctl_new);
}
}
/* finished? */
#ifndef COM_MULTIPORT
if ((inb(com->int_id_port) & IIR_IMASK) == IIR_NOPEND)
#endif /* COM_MULTIPORT */
return;
}
}
static int
sioioctl(dev, cmd, data, flag, p)
dev_t dev;
u_long cmd;
caddr_t data;
int flag;
struct proc *p;
{
struct com_s *com;
int error;
int mynor;
int s;
struct tty *tp;
#if defined(COMPAT_43) || defined(COMPAT_SUNOS)
u_long oldcmd;
struct termios term;
#endif
mynor = minor(dev);
com = com_addr(MINOR_TO_UNIT(mynor));
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL || com->gone)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return (ENODEV);
if (mynor & CONTROL_MASK) {
struct termios *ct;
switch (mynor & CONTROL_MASK) {
case CONTROL_INIT_STATE:
ct = mynor & CALLOUT_MASK ? &com->it_out : &com->it_in;
break;
case CONTROL_LOCK_STATE:
ct = mynor & CALLOUT_MASK ? &com->lt_out : &com->lt_in;
break;
default:
return (ENODEV); /* /dev/nodev */
}
switch (cmd) {
case TIOCSETA:
error = suser(p);
if (error != 0)
return (error);
*ct = *(struct termios *)data;
return (0);
case TIOCGETA:
*(struct termios *)data = *ct;
return (0);
case TIOCGETD:
*(int *)data = TTYDISC;
return (0);
case TIOCGWINSZ:
bzero(data, sizeof(struct winsize));
return (0);
default:
return (ENOTTY);
}
}
tp = com->tp;
#if defined(COMPAT_43) || defined(COMPAT_SUNOS)
term = tp->t_termios;
oldcmd = cmd;
error = ttsetcompat(tp, &cmd, data, &term);
if (error != 0)
return (error);
if (cmd != oldcmd)
data = (caddr_t)&term;
#endif
if (cmd == TIOCSETA || cmd == TIOCSETAW || cmd == TIOCSETAF) {
int cc;
struct termios *dt = (struct termios *)data;
struct termios *lt = mynor & CALLOUT_MASK
? &com->lt_out : &com->lt_in;
dt->c_iflag = (tp->t_iflag & lt->c_iflag)
| (dt->c_iflag & ~lt->c_iflag);
dt->c_oflag = (tp->t_oflag & lt->c_oflag)
| (dt->c_oflag & ~lt->c_oflag);
dt->c_cflag = (tp->t_cflag & lt->c_cflag)
| (dt->c_cflag & ~lt->c_cflag);
dt->c_lflag = (tp->t_lflag & lt->c_lflag)
| (dt->c_lflag & ~lt->c_lflag);
for (cc = 0; cc < NCCS; ++cc)
if (lt->c_cc[cc] != 0)
dt->c_cc[cc] = tp->t_cc[cc];
if (lt->c_ispeed != 0)
dt->c_ispeed = tp->t_ispeed;
if (lt->c_ospeed != 0)
dt->c_ospeed = tp->t_ospeed;
}
error = (*linesw[tp->t_line].l_ioctl)(tp, cmd, data, flag, p);
if (error != ENOIOCTL)
return (error);
s = spltty();
error = ttioctl(tp, cmd, data, flag);
disc_optim(tp, &tp->t_termios, com);
if (error != ENOIOCTL) {
splx(s);
return (error);
}
switch (cmd) {
case TIOCSBRK:
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, com->cfcr_image |= CFCR_SBREAK);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
break;
case TIOCCBRK:
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, com->cfcr_image &= ~CFCR_SBREAK);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
break;
case TIOCSDTR:
(void)commctl(com, TIOCM_DTR, DMBIS);
break;
case TIOCCDTR:
(void)commctl(com, TIOCM_DTR, DMBIC);
break;
/*
* XXX should disallow changing MCR_RTS if CS_RTS_IFLOW is set. The
* changes get undone on the next call to comparam().
*/
case TIOCMSET:
(void)commctl(com, *(int *)data, DMSET);
break;
case TIOCMBIS:
(void)commctl(com, *(int *)data, DMBIS);
break;
case TIOCMBIC:
(void)commctl(com, *(int *)data, DMBIC);
break;
case TIOCMGET:
*(int *)data = commctl(com, 0, DMGET);
break;
case TIOCMSDTRWAIT:
/* must be root since the wait applies to following logins */
error = suser(p);
if (error != 0) {
splx(s);
return (error);
}
com->dtr_wait = *(int *)data * hz / 100;
break;
case TIOCMGDTRWAIT:
*(int *)data = com->dtr_wait * 100 / hz;
break;
case TIOCTIMESTAMP:
com->do_timestamp = TRUE;
*(struct timeval *)data = com->timestamp;
break;
case TIOCDCDTIMESTAMP:
com->do_dcd_timestamp = TRUE;
*(struct timeval *)data = com->dcd_timestamp;
break;
default:
splx(s);
error = pps_ioctl(cmd, data, &com->pps);
if (error == ENODEV)
error = ENOTTY;
return (error);
}
splx(s);
return (0);
}
static void
siopoll()
{
int unit;
if (com_events == 0)
return;
repeat:
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
for (unit = 0; unit < sio_numunits; ++unit) {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
struct com_s *com;
int incc;
struct tty *tp;
com = com_addr(unit);
if (com == NULL)
continue;
tp = com->tp;
if (tp == NULL || com->gone) {
/*
* Discard any events related to never-opened or
* going-away devices.
*/
disable_intr();
incc = com->iptr - com->ibuf;
com->iptr = com->ibuf;
if (com->state & CS_CHECKMSR) {
incc += LOTS_OF_EVENTS;
com->state &= ~CS_CHECKMSR;
}
com_events -= incc;
enable_intr();
continue;
}
if (com->iptr != com->ibuf) {
disable_intr();
sioinput(com);
enable_intr();
}
if (com->state & CS_CHECKMSR) {
u_char delta_modem_status;
disable_intr();
delta_modem_status = com->last_modem_status
^ com->prev_modem_status;
com->prev_modem_status = com->last_modem_status;
com_events -= LOTS_OF_EVENTS;
com->state &= ~CS_CHECKMSR;
enable_intr();
if (delta_modem_status & MSR_DCD)
(*linesw[tp->t_line].l_modem)
(tp, com->prev_modem_status & MSR_DCD);
}
if (com->state & CS_ODONE) {
disable_intr();
com_events -= LOTS_OF_EVENTS;
com->state &= ~CS_ODONE;
enable_intr();
if (!(com->state & CS_BUSY)
&& !(com->extra_state & CSE_BUSYCHECK)) {
timeout(siobusycheck, com, hz / 100);
com->extra_state |= CSE_BUSYCHECK;
}
(*linesw[tp->t_line].l_start)(tp);
}
if (com_events == 0)
break;
}
if (com_events >= LOTS_OF_EVENTS)
goto repeat;
}
static int
comparam(tp, t)
struct tty *tp;
struct termios *t;
{
u_int cfcr;
int cflag;
struct com_s *com;
int divisor;
u_char dlbh;
u_char dlbl;
int s;
int unit;
/* do historical conversions */
if (t->c_ispeed == 0)
t->c_ispeed = t->c_ospeed;
/* check requested parameters */
divisor = ttspeedtab(t->c_ospeed, comspeedtab);
if (divisor < 0 || (divisor > 0 && t->c_ispeed != t->c_ospeed))
return (EINVAL);
/* parameters are OK, convert them to the com struct and the device */
unit = DEV_TO_UNIT(tp->t_dev);
com = com_addr(unit);
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL)
return (ENODEV);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
s = spltty();
if (divisor == 0)
(void)commctl(com, TIOCM_DTR, DMBIC); /* hang up line */
else
(void)commctl(com, TIOCM_DTR, DMBIS);
cflag = t->c_cflag;
switch (cflag & CSIZE) {
case CS5:
cfcr = CFCR_5BITS;
break;
case CS6:
cfcr = CFCR_6BITS;
break;
case CS7:
cfcr = CFCR_7BITS;
break;
default:
cfcr = CFCR_8BITS;
break;
}
if (cflag & PARENB) {
cfcr |= CFCR_PENAB;
if (!(cflag & PARODD))
cfcr |= CFCR_PEVEN;
}
if (cflag & CSTOPB)
cfcr |= CFCR_STOPB;
if (com->hasfifo && divisor != 0) {
/*
* Use a fifo trigger level low enough so that the input
* latency from the fifo is less than about 16 msec and
* the total latency is less than about 30 msec. These
* latencies are reasonable for humans. Serial comms
* protocols shouldn't expect anything better since modem
* latencies are larger.
*/
com->fifo_image = t->c_ospeed <= 4800
? FIFO_ENABLE : FIFO_ENABLE | FIFO_RX_HIGH;
#ifdef COM_ESP
/*
* The Hayes ESP card needs the fifo DMA mode bit set
* in compatibility mode. If not, it will interrupt
* for each character received.
*/
if (com->esp)
com->fifo_image |= FIFO_DMA_MODE;
#endif
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo, com->fifo_image);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
/*
* This returns with interrupts disabled so that we can complete
* the speed change atomically. Keeping interrupts disabled is
* especially important while com_data is hidden.
*/
(void) siosetwater(com, t->c_ispeed);
if (divisor != 0) {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, cfcr | CFCR_DLAB);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/*
* Only set the divisor registers if they would change,
* since on some 16550 incompatibles (UMC8669F), setting
* them while input is arriving them loses sync until
* data stops arriving.
*/
dlbl = divisor & 0xFF;
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
if (sio_getreg(com, com_dlbl) != dlbl)
sio_setreg(com, com_dlbl, dlbl);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
dlbh = (u_int) divisor >> 8;
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
if (sio_getreg(com, com_dlbh) != dlbh)
sio_setreg(com, com_dlbh, dlbh);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, com->cfcr_image = cfcr);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (!(tp->t_state & TS_TTSTOP))
com->state |= CS_TTGO;
if (cflag & CRTS_IFLOW) {
if (com->st16650a) {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, 0xbf);
sio_setreg(com, com_fifo,
sio_getreg(com, com_fifo) | 0x40);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
com->state |= CS_RTS_IFLOW;
/*
* If CS_RTS_IFLOW just changed from off to on, the change
* needs to be propagated to MCR_RTS. This isn't urgent,
* so do it later by calling comstart() instead of repeating
* a lot of code from comstart() here.
*/
} else if (com->state & CS_RTS_IFLOW) {
com->state &= ~CS_RTS_IFLOW;
/*
* CS_RTS_IFLOW just changed from on to off. Force MCR_RTS
* on here, since comstart() won't do it later.
*/
outb(com->modem_ctl_port, com->mcr_image |= MCR_RTS);
if (com->st16650a) {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, 0xbf);
sio_setreg(com, com_fifo,
sio_getreg(com, com_fifo) & ~0x40);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
}
/*
* Set up state to handle output flow control.
* XXX - worth handling MDMBUF (DCD) flow control at the lowest level?
* Now has 10+ msec latency, while CTS flow has 50- usec latency.
*/
com->state |= CS_ODEVREADY;
com->state &= ~CS_CTS_OFLOW;
if (cflag & CCTS_OFLOW) {
com->state |= CS_CTS_OFLOW;
if (!(com->last_modem_status & MSR_CTS))
com->state &= ~CS_ODEVREADY;
if (com->st16650a) {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, 0xbf);
sio_setreg(com, com_fifo,
sio_getreg(com, com_fifo) | 0x80);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
} else {
if (com->st16650a) {
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, 0xbf);
sio_setreg(com, com_fifo,
sio_getreg(com, com_fifo) & ~0x80);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
}
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_cfcr, com->cfcr_image);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
/* XXX shouldn't call functions while intrs are disabled. */
disc_optim(tp, t, com);
/*
* Recover from fiddling with CS_TTGO. We used to call siointr1()
* unconditionally, but that defeated the careful discarding of
* stale input in sioopen().
*/
if (com->state >= (CS_BUSY | CS_TTGO))
siointr1(com);
enable_intr();
splx(s);
comstart(tp);
if (com->ibufold != NULL) {
free(com->ibufold, M_DEVBUF);
com->ibufold = NULL;
}
return (0);
}
static int
siosetwater(com, speed)
struct com_s *com;
speed_t speed;
{
int cp4ticks;
u_char *ibuf;
int ibufsize;
struct tty *tp;
/*
* Make the buffer size large enough to handle a softtty interrupt
* latency of about 2 ticks without loss of throughput or data
* (about 3 ticks if input flow control is not used or not honoured,
* but a bit less for CS5-CS7 modes).
*/
cp4ticks = speed / 10 / hz * 4;
for (ibufsize = 128; ibufsize < cp4ticks;)
ibufsize <<= 1;
if (ibufsize == com->ibufsize) {
disable_intr();
return (0);
}
/*
* Allocate input buffer. The extra factor of 2 in the size is
* to allow for an error byte for each input byte.
*/
ibuf = malloc(2 * ibufsize, M_DEVBUF, M_NOWAIT);
if (ibuf == NULL) {
disable_intr();
return (ENOMEM);
}
/* Initialize non-critical variables. */
com->ibufold = com->ibuf;
com->ibufsize = ibufsize;
tp = com->tp;
if (tp != NULL) {
tp->t_ififosize = 2 * ibufsize;
tp->t_ispeedwat = (speed_t)-1;
tp->t_ospeedwat = (speed_t)-1;
}
/*
* Read current input buffer, if any. Continue with interrupts
* disabled.
*/
disable_intr();
if (com->iptr != com->ibuf)
sioinput(com);
/*-
* Initialize critical variables, including input buffer watermarks.
* The external device is asked to stop sending when the buffer
* exactly reaches high water, or when the high level requests it.
* The high level is notified immediately (rather than at a later
* clock tick) when this watermark is reached.
* The buffer size is chosen so the watermark should almost never
* be reached.
* The low watermark is invisibly 0 since the buffer is always
* emptied all at once.
*/
com->iptr = com->ibuf = ibuf;
com->ibufend = ibuf + ibufsize;
com->ierroff = ibufsize;
com->ihighwater = ibuf + 3 * ibufsize / 4;
return (0);
}
static void
comstart(tp)
struct tty *tp;
{
struct com_s *com;
int s;
int unit;
unit = DEV_TO_UNIT(tp->t_dev);
com = com_addr(unit);
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL)
return;
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
s = spltty();
disable_intr();
if (tp->t_state & TS_TTSTOP)
com->state &= ~CS_TTGO;
else
com->state |= CS_TTGO;
if (tp->t_state & TS_TBLOCK) {
if (com->mcr_image & MCR_RTS && com->state & CS_RTS_IFLOW)
outb(com->modem_ctl_port, com->mcr_image &= ~MCR_RTS);
} else {
if (!(com->mcr_image & MCR_RTS) && com->iptr < com->ihighwater
&& com->state & CS_RTS_IFLOW)
outb(com->modem_ctl_port, com->mcr_image |= MCR_RTS);
}
enable_intr();
if (tp->t_state & (TS_TIMEOUT | TS_TTSTOP)) {
ttwwakeup(tp);
splx(s);
return;
}
if (tp->t_outq.c_cc != 0) {
struct lbq *qp;
struct lbq *next;
if (!com->obufs[0].l_queued) {
com->obufs[0].l_tail
= com->obuf1 + q_to_b(&tp->t_outq, com->obuf1,
sizeof com->obuf1);
com->obufs[0].l_next = NULL;
com->obufs[0].l_queued = TRUE;
disable_intr();
if (com->state & CS_BUSY) {
qp = com->obufq.l_next;
while ((next = qp->l_next) != NULL)
qp = next;
qp->l_next = &com->obufs[0];
} else {
com->obufq.l_head = com->obufs[0].l_head;
com->obufq.l_tail = com->obufs[0].l_tail;
com->obufq.l_next = &com->obufs[0];
com->state |= CS_BUSY;
}
enable_intr();
}
if (tp->t_outq.c_cc != 0 && !com->obufs[1].l_queued) {
com->obufs[1].l_tail
= com->obuf2 + q_to_b(&tp->t_outq, com->obuf2,
sizeof com->obuf2);
com->obufs[1].l_next = NULL;
com->obufs[1].l_queued = TRUE;
disable_intr();
if (com->state & CS_BUSY) {
qp = com->obufq.l_next;
while ((next = qp->l_next) != NULL)
qp = next;
qp->l_next = &com->obufs[1];
} else {
com->obufq.l_head = com->obufs[1].l_head;
com->obufq.l_tail = com->obufs[1].l_tail;
com->obufq.l_next = &com->obufs[1];
com->state |= CS_BUSY;
}
enable_intr();
}
tp->t_state |= TS_BUSY;
}
disable_intr();
if (com->state >= (CS_BUSY | CS_TTGO))
siointr1(com); /* fake interrupt to start output */
enable_intr();
ttwwakeup(tp);
splx(s);
}
static void
This patch clears the way for removing a number of tty related fields in struct cdevsw: d_stop moved to struct tty. d_reset already unused. d_devtotty linkage now provided by dev_t->si_tty. These fields will be removed from struct cdevsw together with d_params and d_maxio Real Soon Now. The changes in this patch consist of: initialize dev->si_tty in *_open() initialize tty->t_stop remove devtotty functions rename ttpoll to ttypoll a few adjustments to these changes in the generic code a bump of __FreeBSD_version add a couple of FreeBSD tags
1999-09-25 16:21:39 +00:00
comstop(tp, rw)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
struct tty *tp;
int rw;
{
struct com_s *com;
com = com_addr(DEV_TO_UNIT(tp->t_dev));
Fix crashes on card eject for pccard modems. We check for NULL when we get the com address. If so, we go ahead and return. Bruce thinks there's a bug in the pccard layer that it terminates devices with extreme prejustice rather than letting them deside for themselves when to terminate (and he's likely right). This fix doesn't change that, but instead works around it by checking for NULL pointers at more places than before. The detach routine still calls functions at interrupt level that aren't reentrant. In theory this could cause a problem, but none showed up in practice. Future versions should correct this problem, likely by making the detach process a thread/process at the pccard level. NEWCARD will do this, and the current pccard layer should likely be modified to that as well, should it live long enough. A few style nits of the same form that were in my original patch sent off to bde were also fixed as part of this process. Mostly use of !ptr and return ENOPARENS. This should prevent a crash on suspend with an active ppp link as well, but that wasn't tested. Reviewed by: bde Approved by: jkh
2000-03-11 20:22:09 +00:00
if (com == NULL || com->gone)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
return;
disable_intr();
if (rw & FWRITE) {
if (com->hasfifo)
#ifdef COM_ESP
/* XXX avoid h/w bug. */
if (!com->esp)
#endif
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo,
FIFO_XMT_RST | com->fifo_image);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com->obufs[0].l_queued = FALSE;
com->obufs[1].l_queued = FALSE;
if (com->state & CS_ODONE)
com_events -= LOTS_OF_EVENTS;
com->state &= ~(CS_ODONE | CS_BUSY);
com->tp->t_state &= ~TS_BUSY;
}
if (rw & FREAD) {
if (com->hasfifo)
#ifdef COM_ESP
/* XXX avoid h/w bug. */
if (!com->esp)
#endif
Use bus_space stuff except where it needs high performance. Reviewed by: bde
2000-05-12 12:37:28 +00:00
sio_setreg(com, com_fifo,
FIFO_RCV_RST | com->fifo_image);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com_events -= (com->iptr - com->ibuf);
com->iptr = com->ibuf;
}
enable_intr();
comstart(tp);
}
static int
commctl(com, bits, how)
struct com_s *com;
int bits;
int how;
{
int mcr;
int msr;
if (how == DMGET) {
bits = TIOCM_LE; /* XXX - always enabled while open */
mcr = com->mcr_image;
if (mcr & MCR_DTR)
bits |= TIOCM_DTR;
if (mcr & MCR_RTS)
bits |= TIOCM_RTS;
msr = com->prev_modem_status;
if (msr & MSR_CTS)
bits |= TIOCM_CTS;
if (msr & MSR_DCD)
bits |= TIOCM_CD;
if (msr & MSR_DSR)
bits |= TIOCM_DSR;
/*
* XXX - MSR_RI is naturally volatile, and we make MSR_TERI
* more volatile by reading the modem status a lot. Perhaps
* we should latch both bits until the status is read here.
*/
if (msr & (MSR_RI | MSR_TERI))
bits |= TIOCM_RI;
return (bits);
}
mcr = 0;
if (bits & TIOCM_DTR)
mcr |= MCR_DTR;
if (bits & TIOCM_RTS)
mcr |= MCR_RTS;
if (com->gone)
return(0);
disable_intr();
switch (how) {
case DMSET:
outb(com->modem_ctl_port,
com->mcr_image = mcr | (com->mcr_image & MCR_IENABLE));
break;
case DMBIS:
outb(com->modem_ctl_port, com->mcr_image |= mcr);
break;
case DMBIC:
outb(com->modem_ctl_port, com->mcr_image &= ~mcr);
break;
}
enable_intr();
return (0);
}
static void
siosettimeout()
{
struct com_s *com;
bool_t someopen;
int unit;
/*
* Set our timeout period to 1 second if no polled devices are open.
* Otherwise set it to max(1/200, 1/hz).
* Enable timeouts iff some device is open.
*/
untimeout(comwakeup, (void *)NULL, sio_timeout_handle);
sio_timeout = hz;
someopen = FALSE;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
for (unit = 0; unit < sio_numunits; ++unit) {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com = com_addr(unit);
if (com != NULL && com->tp != NULL
&& com->tp->t_state & TS_ISOPEN && !com->gone) {
someopen = TRUE;
if (com->poll || com->poll_output) {
sio_timeout = hz > 200 ? hz / 200 : 1;
break;
}
}
}
if (someopen) {
sio_timeouts_until_log = hz / sio_timeout;
sio_timeout_handle = timeout(comwakeup, (void *)NULL,
sio_timeout);
} else {
/* Flush error messages, if any. */
sio_timeouts_until_log = 1;
comwakeup((void *)NULL);
untimeout(comwakeup, (void *)NULL, sio_timeout_handle);
}
}
static void
comwakeup(chan)
void *chan;
{
struct com_s *com;
int unit;
sio_timeout_handle = timeout(comwakeup, (void *)NULL, sio_timeout);
/*
* Recover from lost output interrupts.
* Poll any lines that don't use interrupts.
*/
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
for (unit = 0; unit < sio_numunits; ++unit) {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
com = com_addr(unit);
if (com != NULL && !com->gone
&& (com->state >= (CS_BUSY | CS_TTGO) || com->poll)) {
disable_intr();
siointr1(com);
enable_intr();
}
}
/*
* Check for and log errors, but not too often.
*/
if (--sio_timeouts_until_log > 0)
return;
sio_timeouts_until_log = hz / sio_timeout;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
for (unit = 0; unit < sio_numunits; ++unit) {
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
int errnum;
com = com_addr(unit);
if (com == NULL)
continue;
if (com->gone)
continue;
for (errnum = 0; errnum < CE_NTYPES; ++errnum) {
u_int delta;
u_long total;
disable_intr();
delta = com->delta_error_counts[errnum];
com->delta_error_counts[errnum] = 0;
enable_intr();
if (delta == 0)
continue;
total = com->error_counts[errnum] += delta;
log(LOG_ERR, "sio%d: %u more %s%s (total %lu)\n",
unit, delta, error_desc[errnum],
delta == 1 ? "" : "s", total);
}
}
}
static void
disc_optim(tp, t, com)
struct tty *tp;
struct termios *t;
struct com_s *com;
{
if (!(t->c_iflag & (ICRNL | IGNCR | IMAXBEL | INLCR | ISTRIP | IXON))
&& (!(t->c_iflag & BRKINT) || (t->c_iflag & IGNBRK))
&& (!(t->c_iflag & PARMRK)
|| (t->c_iflag & (IGNPAR | IGNBRK)) == (IGNPAR | IGNBRK))
&& !(t->c_lflag & (ECHO | ICANON | IEXTEN | ISIG | PENDIN))
&& linesw[tp->t_line].l_rint == ttyinput)
tp->t_state |= TS_CAN_BYPASS_L_RINT;
else
tp->t_state &= ~TS_CAN_BYPASS_L_RINT;
com->hotchar = linesw[tp->t_line].l_hotchar;
}
/*
* Following are all routines needed for SIO to act as console
*/
#include <sys/cons.h>
struct siocnstate {
u_char dlbl;
u_char dlbh;
u_char ier;
u_char cfcr;
u_char mcr;
};
static speed_t siocngetspeed __P((Port_t, struct speedtab *));
static void siocnclose __P((struct siocnstate *sp, Port_t iobase));
static void siocnopen __P((struct siocnstate *sp, Port_t iobase, int speed));
static void siocntxwait __P((Port_t iobase));
static cn_probe_t siocnprobe;
static cn_init_t siocninit;
static cn_checkc_t siocncheckc;
static cn_getc_t siocngetc;
static cn_putc_t siocnputc;
#ifdef __i386__
Add a new mechanism, cndbctl(), to tell the console driver that ddb is entered. Don't refer to `in_Debugger' to see if we are in the debugger. (The variable used to be static in Debugger() and wasn't updated if ddb is entered via traps and panic anyway.) - Don't refer to `in_Debugger'. - Add `db_active' to i386/i386/db_interface.d (as in alpha/alpha/db_interface.c). - Remove cnpollc() stub from ddb/db_input.c. - Add the dbctl function to syscons, pcvt, and sio. (The function for pcvt and sio is noop at the moment.) Jointly developed by: bde and me (The final version was tweaked by me and not reviewed by bde. Thus, if there is any error in this commit, that is entirely of mine, not his.) Some changes were obtained from: NetBSD
2000-01-11 14:54:01 +00:00
CONS_DRIVER(sio, siocnprobe, siocninit, NULL, siocngetc, siocncheckc,
siocnputc, NULL);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
#endif
/* To get the GDB related variables */
#if DDB > 0
#include <ddb/ddb.h>
#endif
static void
siocntxwait(iobase)
Port_t iobase;
{
int timo;
/*
* Wait for any pending transmission to finish. Required to avoid
* the UART lockup bug when the speed is changed, and for normal
* transmits.
*/
timo = 100000;
while ((inb(iobase + com_lsr) & (LSR_TSRE | LSR_TXRDY))
!= (LSR_TSRE | LSR_TXRDY) && --timo != 0)
;
}
/*
* Read the serial port specified and try to figure out what speed
* it's currently running at. We're assuming the serial port has
* been initialized and is basicly idle. This routine is only intended
* to be run at system startup.
*
* If the value read from the serial port doesn't make sense, return 0.
*/
static speed_t
siocngetspeed(iobase, table)
Port_t iobase;
struct speedtab *table;
{
int code;
u_char dlbh;
u_char dlbl;
u_char cfcr;
cfcr = inb(iobase + com_cfcr);
outb(iobase + com_cfcr, CFCR_DLAB | cfcr);
dlbl = inb(iobase + com_dlbl);
dlbh = inb(iobase + com_dlbh);
outb(iobase + com_cfcr, cfcr);
code = dlbh << 8 | dlbl;
Merge some typo fixes from dev/sio/sio.c (siostop -> comstop) Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c) Make sio work for pccard here - pccardd doesn't activate interrupts until after prove has succeeded. Mark the initial reset of likely sio ports as broken as it depended on config supplying a list of locations to probe, devices are now proved standalone. Optimize a bit of COM_NOAST4() logic. Use bus_get_resource_start() etc rather than using isa-centric calls. Reactivate the IIR_TXRDYBUG test, I've got a card here with it. Try to be a bit smarter about activating interrupts (ie: don't panic if polled) Fix some style bugs that have crept in over time (there are still more).
1999-11-18 07:22:41 +00:00
for (; table->sp_speed != -1; table++)
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
if (table->sp_code == code)
return (table->sp_speed);
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
return (0); /* didn't match anything sane */
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
static void
siocnopen(sp, iobase, speed)
struct siocnstate *sp;
Port_t iobase;
int speed;
{
int divisor;
u_char dlbh;
u_char dlbl;
/*
* Save all the device control registers except the fifo register
* and set our default ones (cs8 -parenb speed=comdefaultrate).
* We can't save the fifo register since it is read-only.
*/
sp->ier = inb(iobase + com_ier);
outb(iobase + com_ier, 0); /* spltty() doesn't stop siointr() */
siocntxwait(iobase);
sp->cfcr = inb(iobase + com_cfcr);
outb(iobase + com_cfcr, CFCR_DLAB | CFCR_8BITS);
sp->dlbl = inb(iobase + com_dlbl);
sp->dlbh = inb(iobase + com_dlbh);
/*
* Only set the divisor registers if they would change, since on
* some 16550 incompatibles (Startech), setting them clears the
* data input register. This also reduces the effects of the
* UMC8669F bug.
*/
divisor = ttspeedtab(speed, comspeedtab);
dlbl = divisor & 0xFF;
if (sp->dlbl != dlbl)
outb(iobase + com_dlbl, dlbl);
dlbh = (u_int) divisor >> 8;
if (sp->dlbh != dlbh)
outb(iobase + com_dlbh, dlbh);
outb(iobase + com_cfcr, CFCR_8BITS);
sp->mcr = inb(iobase + com_mcr);
/*
* We don't want interrupts, but must be careful not to "disable"
* them by clearing the MCR_IENABLE bit, since that might cause
* an interrupt by floating the IRQ line.
*/
outb(iobase + com_mcr, (sp->mcr & MCR_IENABLE) | MCR_DTR | MCR_RTS);
}
static void
siocnclose(sp, iobase)
struct siocnstate *sp;
Port_t iobase;
{
/*
* Restore the device control registers.
*/
siocntxwait(iobase);
outb(iobase + com_cfcr, CFCR_DLAB | CFCR_8BITS);
if (sp->dlbl != inb(iobase + com_dlbl))
outb(iobase + com_dlbl, sp->dlbl);
if (sp->dlbh != inb(iobase + com_dlbh))
outb(iobase + com_dlbh, sp->dlbh);
outb(iobase + com_cfcr, sp->cfcr);
/*
* XXX damp oscillations of MCR_DTR and MCR_RTS by not restoring them.
*/
outb(iobase + com_mcr, sp->mcr | MCR_DTR | MCR_RTS);
outb(iobase + com_ier, sp->ier);
}
static void
siocnprobe(cp)
struct consdev *cp;
{
speed_t boot_speed;
u_char cfcr;
int s, unit;
struct siocnstate sp;
/*
* Find our first enabled console, if any. If it is a high-level
* console device, then initialize it and return successfully.
* If it is a low-level console device, then initialize it and
* return unsuccessfully. It must be initialized in both cases
* for early use by console drivers and debuggers. Initializing
* the hardware is not necessary in all cases, since the i/o
* routines initialize it on the fly, but it is necessary if
* input might arrive while the hardware is switched back to an
* uninitialized state. We can't handle multiple console devices
* yet because our low-level routines don't take a device arg.
* We trust the user to set the console flags properly so that we
* don't need to probe.
*/
cp->cn_pri = CN_DEAD;
for (unit = 0; unit < 16; unit++) { /* XXX need to know how many */
int flags;
int disabled;
if (resource_int_value("sio", unit, "disabled", &disabled) == 0) {
if (disabled)
continue;
}
if (resource_int_value("sio", unit, "flags", &flags))
continue;
if (COM_CONSOLE(flags) || COM_DEBUGGER(flags)) {
int port;
Port_t iobase;
if (resource_int_value("sio", unit, "port", &port))
continue;
iobase = port;
s = spltty();
if (boothowto & RB_SERIAL) {
boot_speed = siocngetspeed(iobase, comspeedtab);
if (boot_speed)
comdefaultrate = boot_speed;
}
/*
* Initialize the divisor latch. We can't rely on
* siocnopen() to do this the first time, since it
* avoids writing to the latch if the latch appears
* to have the correct value. Also, if we didn't
* just read the speed from the hardware, then we
* need to set the speed in hardware so that
* switching it later is null.
*/
cfcr = inb(iobase + com_cfcr);
outb(iobase + com_cfcr, CFCR_DLAB | cfcr);
outb(iobase + com_dlbl,
COMBRD(comdefaultrate) & 0xff);
outb(iobase + com_dlbh,
(u_int) COMBRD(comdefaultrate) >> 8);
outb(iobase + com_cfcr, cfcr);
siocnopen(&sp, iobase, comdefaultrate);
splx(s);
if (COM_CONSOLE(flags) && !COM_LLCONSOLE(flags)) {
cp->cn_dev = makedev(CDEV_MAJOR, unit);
cp->cn_pri = COM_FORCECONSOLE(flags)
|| boothowto & RB_SERIAL
? CN_REMOTE : CN_NORMAL;
siocniobase = iobase;
siocnunit = unit;
}
if (COM_DEBUGGER(flags)) {
printf("sio%d: gdb debugging port\n", unit);
siogdbiobase = iobase;
siogdbunit = unit;
#if DDB > 0
gdbdev = makedev(CDEV_MAJOR, unit);
gdb_getc = siocngetc;
gdb_putc = siocnputc;
#endif
}
}
}
#ifdef __i386__
#if DDB > 0
/*
* XXX Ugly Compatability.
* If no gdb port has been specified, set it to be the console
* as some configuration files don't specify the gdb port.
*/
if (gdbdev == NODEV && (boothowto & RB_GDB)) {
printf("Warning: no GDB port specified. Defaulting to sio%d.\n",
siocnunit);
printf("Set flag 0x80 on desired GDB port in your\n");
printf("configuration file (currently sio only).\n");
siogdbiobase = siocniobase;
siogdbunit = siocnunit;
gdbdev = makedev(CDEV_MAJOR, siocnunit);
gdb_getc = siocngetc;
gdb_putc = siocnputc;
}
#endif
#endif
}
#ifdef __alpha__
Make this compile on alpha
2000-01-13 02:09:44 +00:00
CONS_DRIVER(sio, NULL, NULL, NULL, siocngetc, siocncheckc, siocnputc, NULL);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
int
siocnattach(port, speed)
int port;
int speed;
{
int s;
u_char cfcr;
struct siocnstate sp;
siocniobase = port;
comdefaultrate = speed;
sio_consdev.cn_pri = CN_NORMAL;
sio_consdev.cn_dev = makedev(CDEV_MAJOR, 0);
s = spltty();
/*
* Initialize the divisor latch. We can't rely on
* siocnopen() to do this the first time, since it
* avoids writing to the latch if the latch appears
* to have the correct value. Also, if we didn't
* just read the speed from the hardware, then we
* need to set the speed in hardware so that
* switching it later is null.
*/
cfcr = inb(siocniobase + com_cfcr);
outb(siocniobase + com_cfcr, CFCR_DLAB | cfcr);
outb(siocniobase + com_dlbl,
COMBRD(comdefaultrate) & 0xff);
outb(siocniobase + com_dlbh,
(u_int) COMBRD(comdefaultrate) >> 8);
outb(siocniobase + com_cfcr, cfcr);
siocnopen(&sp, siocniobase, comdefaultrate);
splx(s);
cn_tab = &sio_consdev;
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
return (0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
int
siogdbattach(port, speed)
int port;
int speed;
{
int s;
u_char cfcr;
struct siocnstate sp;
siogdbiobase = port;
gdbdefaultrate = speed;
s = spltty();
/*
* Initialize the divisor latch. We can't rely on
* siocnopen() to do this the first time, since it
* avoids writing to the latch if the latch appears
* to have the correct value. Also, if we didn't
* just read the speed from the hardware, then we
* need to set the speed in hardware so that
* switching it later is null.
*/
cfcr = inb(siogdbiobase + com_cfcr);
outb(siogdbiobase + com_cfcr, CFCR_DLAB | cfcr);
outb(siogdbiobase + com_dlbl,
COMBRD(gdbdefaultrate) & 0xff);
outb(siogdbiobase + com_dlbh,
(u_int) COMBRD(gdbdefaultrate) >> 8);
outb(siogdbiobase + com_cfcr, cfcr);
siocnopen(&sp, siogdbiobase, gdbdefaultrate);
splx(s);
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
return (0);
Restore the old sio* - bruce can fix it himself.
1999-09-08 10:59:03 +00:00
}
#endif
static void
siocninit(cp)
struct consdev *cp;
{
comconsole = DEV_TO_UNIT(cp->cn_dev);
}
static int
siocncheckc(dev)
dev_t dev;
{
int c;
Port_t iobase;
int s;
struct siocnstate sp;
if (minor(dev) == siogdbunit)
iobase = siogdbiobase;
else
iobase = siocniobase;
s = spltty();
siocnopen(&sp, iobase, comdefaultrate);
if (inb(iobase + com_lsr) & LSR_RXRDY)
c = inb(iobase + com_data);
else
c = -1;
siocnclose(&sp, iobase);
splx(s);
return (c);
}
int
siocngetc(dev)
dev_t dev;
{
int c;
Port_t iobase;
int s;
struct siocnstate sp;
if (minor(dev) == siogdbunit)
iobase = siogdbiobase;
else
iobase = siocniobase;
s = spltty();
siocnopen(&sp, iobase, comdefaultrate);
while (!(inb(iobase + com_lsr) & LSR_RXRDY))
;
c = inb(iobase + com_data);
siocnclose(&sp, iobase);
splx(s);
return (c);
}
void
siocnputc(dev, c)
dev_t dev;
int c;
{
int s;
struct siocnstate sp;
Port_t iobase;
if (minor(dev) == siogdbunit)
iobase = siogdbiobase;
else
iobase = siocniobase;
s = spltty();
siocnopen(&sp, iobase, comdefaultrate);
siocntxwait(iobase);
outb(iobase + com_data, c);
siocnclose(&sp, iobase);
splx(s);
}
#ifdef __alpha__
int
siogdbgetc()
{
int c;
Port_t iobase;
int s;
struct siocnstate sp;
iobase = siogdbiobase;
s = spltty();
siocnopen(&sp, iobase, gdbdefaultrate);
while (!(inb(iobase + com_lsr) & LSR_RXRDY))
;
c = inb(iobase + com_data);
siocnclose(&sp, iobase);
splx(s);
return (c);
}
void
siogdbputc(c)
int c;
{
int s;
struct siocnstate sp;
s = spltty();
siocnopen(&sp, siogdbiobase, gdbdefaultrate);
siocntxwait(siogdbiobase);
outb(siogdbiobase + com_data, c);
siocnclose(&sp, siogdbiobase);
splx(s);
}
#endif
Add newbus pccard attachment for sio. Some of this code was written by Peter Wemm, but I've not merged all the changes he sent to me yet. This has not been reviewed by bde, so I'm committing to resolve any issues he has with this when he returns from FreeBSD CON 99. I've had four reports of this working for them. I've been able to communicate to both my built in modem and a pccard modem with these patches.
1999-10-25 02:46:52 +00:00
DRIVER_MODULE(sio, isa, sio_isa_driver, sio_devclass, 0, 0);
#if NCARD > 0
DRIVER_MODULE(sio, pccard, sio_pccard_driver, sio_devclass, 0, 0);
#endif
Add support for pci modems. ONLY CONTROLLER BASED MODEMS. This doesn't support winmodems, softmodems, hcf or any other modem that relies on the host to do any sort of soft control for any aspect of the modem's function. There are two modems known to work: 3COM FaxModem PCI. ActionTec 56k VoiceMessaging PCI Modem and the following modem might work Multitech PCI FaxModem (not sure about this) and the serial pci cards might work too. I have neither these hardware items so I can't add support for them.
2000-04-01 06:14:21 +00:00
#if NPCI > 0
DRIVER_MODULE(sio, pci, sio_pci_driver, sio_devclass, 0, 0);
#endif
Reference in New Issue Copy Permalink