1
0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-05 09:14:03 +00:00

Style cleanups on ifconfig.8

fix igor warnings
uppercase all instances of Ethernet
replace bad e.g.

CR:		D91
Approved by:	wblock (mentor)
This commit is contained in:
Allan Jude 2014-06-06 00:22:19 +00:00
parent 11033496a1
commit 96db02f25a
Notes: svn2git 2020-12-20 02:59:44 +00:00
svn path=/head/; revision=267141

View File

@ -28,7 +28,7 @@
.\" From: @(#)ifconfig.8 8.3 (Berkeley) 1/5/94
.\" $FreeBSD$
.\"
.Dd October 21, 2013
.Dd June 5, 2014
.Dt IFCONFIG 8
.Os
.Sh NAME
@ -141,13 +141,13 @@ The link-level
.Pq Dq link
address
is specified as a series of colon-separated hex digits.
This can be used to
e.g.,\& set a new MAC address on an ethernet interface, though the
mechanism used is not ethernet-specific.
This can be used to, for example,
set a new MAC address on an Ethernet interface, though the
mechanism used is not Ethernet specific.
If the interface is already
up when this option is used, it will be briefly brought down and
then brought back up again in order to ensure that the receive
filter in the underlying ethernet hardware is properly reprogrammed.
filter in the underlying Ethernet hardware is properly reprogrammed.
.It Ar address_family
Specify the
address family
@ -179,7 +179,7 @@ or
.Dq lladdr .
Specifying
.Fl l Dq ether
will list only ethernet interfaces, excluding all other interface types,
will list only Ethernet interfaces, excluding all other interface types,
including the loopback interface.
.It Ar dest_address
Specify the address of the correspondent on the other end
@ -661,7 +661,8 @@ Clear a flag
.Cm defaultif .
.It Cm ifdisabled
Set a flag to disable all of IPv6 network communications on the
specified interface. Note that if there are already configured IPv6
specified interface.
Note that if there are already configured IPv6
addresses on that interface, all of them are marked as
.Dq tentative
and DAD will be performed when this flag is cleared.
@ -1087,7 +1088,8 @@ specifies the number of beacon intervals between DTIM
and must be in the range 1 to 15.
By default DTIM is 1 (i.e., DTIM occurs at each beacon).
.It Cm quiet
Enable the use of quiet IE. Hostap will use this to silence other
Enable the use of quiet IE.
Hostap will use this to silence other
stations to reduce interference for radar detection when
operating on 5GHz frequency and doth support is enabled.
Use
@ -1102,9 +1104,11 @@ scheduled quiet intervals defined by Quiet element.
Set the QUIET
.Ar count
to the number of TBTTs until the beacon interval during which the
next quiet interval shall start. A value of 1 indicates the quiet
next quiet interval shall start.
A value of 1 indicates the quiet
interval will start during the beacon interval starting at the next
TBTT. A value 0 is reserved.
TBTT.
A value 0 is reserved.
.It Cm quiet_offset Ar offset
Set the QUIET
.Ar offset
@ -2354,7 +2358,8 @@ Another name for the
parameter.
.It Cm accept_rev_ethip_ver
Set a flag to accept both correct EtherIP packets and ones
with reversed version field. Enabled by default.
with reversed version field.
Enabled by default.
This is for backward compatibility with
.Fx 6.1 ,
6.2, 6.3, 7.0, and 7.1.
@ -2363,7 +2368,8 @@ Clear a flag
.Cm accept_rev_ethip_ver .
.It Cm send_rev_ethip_ver
Set a flag to send EtherIP packets with reversed version
field intentionally. Disabled by default.
field intentionally.
Disabled by default.
This is for backward compatibility with
.Fx 6.1 ,
6.2, 6.3, 7.0, and 7.1.
@ -2446,7 +2452,7 @@ pseudo-interface.
The
.Xr vlan 4
interface is assigned a
copy of the parent interface's flags and the parent's ethernet address.
copy of the parent interface's flags and the parent's Ethernet address.
The
.Cm vlandev
and
@ -2570,7 +2576,7 @@ If an
.Ar address_family
is specified, only interfaces of that type will be listed.
.Fl l Dq ether
will list only ethernet adapters, excluding the loopback interface.
will list only Ethernet adapters, excluding the loopback interface.
Use of this flag is mutually exclusive
with all other flags and commands, except for
.Fl d