- Use strlcpy() instead of strcpy().
- Use strlcat() instead of a strlcpy() with a magic number subtracted
from the length.
- Replace strncmp(..., strlen(foo) + 1) with strcmp(...).
Differential Revision: https://reviews.freebsd.org/D1814
Reviewed by: rpaulo
MFC after: 2 weeks
to obtain IPv4 next hop address in tablearg case.
Add `fwd tablearg' support for IPv6. ipfw(8) uses INADDR_ANY as next hop
address in O_FORWARD_IP opcode for specifying tablearg case. For IPv6 we
still use this opcode, but when packet identified as IPv6 packet, we
obtain next hop address from dedicated field nh6 in struct table_value.
Replace hopstore field in struct ip_fw_args with anonymous union and add
hopstore6 field. Use this field to copy tablearg value for IPv6.
Replace spare1 field in struct table_value with zoneid. Use it to keep
scope zone id for link-local IPv6 addresses. Since spare1 was used
internally, replace spare0 array with two variables spare0 and spare1.
Use getaddrinfo(3)/getnameinfo(3) functions for parsing and formatting
IPv6 addresses in table_value. Use zoneid field in struct table_value
to store sin6_scope_id value.
Since the kernel still uses embedded scope zone id to represent
link-local addresses, convert next_hop6 address into this form before
return from pfil processing. This also fixes in6_localip() check
for link-local addresses.
Differential Revision: https://reviews.freebsd.org/D2015
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
- Add no_dad and ignoreloop per-IF knob. no_dad disables DAD completely,
and ignoreloop is to prevent infinite loop in loopback probing state when
loopback is permanently expected.
block of free space after existing partition, take into account
provider's stripeoffset, since the result will be adjusted to this
value.
PR: 197989
MFC after: 1 week
properly.
If there is garbage in the flags field, it can sometimes include a
set CDAI_FLAG_STORE flag, which may cause either an error or
perhaps result in overwriting the field that was intended to be
read.
sys/cam/cam_ccb.h:
Add a new flag to the XPT_DEV_ADVINFO CCB, CDAI_FLAG_NONE,
that callers can use to set the flags field when no store
is desired.
sys/cam/scsi/scsi_enc_ses.c:
In ses_setphyspath_callback(), explicitly set the
XPT_DEV_ADVINFO flags to CDAI_FLAG_NONE when fetching the
physical path information. Instead of ORing in the
CDAI_FLAG_STORE flag when storing the physical path, set
the flags field to CDAI_FLAG_STORE.
sys/cam/scsi/scsi_sa.c:
Set the XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE when
fetching extended inquiry information.
sys/cam/scsi/scsi_da.c:
When storing extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_STORE instead of
ORing it into a field that isn't initialized.
sys/dev/mpr/mpr_sas.c,
sys/dev/mps/mps_sas.c:
When fetching extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE instead of
setting it to 0.
sbin/camcontrol/camcontrol.c:
When fetching a device ID, set the XPT_DEV_ADVINFO flags
field to CDAI_FLAG_NONE instead of 0.
sys/sys/param.h:
Bump __FreeBSD_version to 1100061 for the new XPT_DEV_ADVINFO
CCB flag, CDAI_FLAG_NONE.
Sponsored by: Spectra Logic
MFC after: 1 week
sysctl... This is useful for kern.arandom which (without -B) will
happily return 0 bytes, which isn't too useful or random...
fix spelling (thanks igor!) of settable while I'm here...
Reverse the sorting order of the interfaces addresses familise so it should be
the same as getifaddrs(3) order. [2]
Suggested by: hrs [1], bz [2]
Approved by: hrs, bapt
based on the address family. This should help to recognize interfaces with
multiple AF (e.g. ipv4 and ipv6) with many aliases or additional addresses. The
order of addresses inside a single group is strictly preserved.
Improve the scope_id output for AF_INET6 families, as the
current approach uses hexadecimal string that is basically the ID of an
interface, whilst this information is already depicted by getnameinfo(3) call.
Therefore, now ifconfig just prints the scope of address as it is defined in
2.4 of RFC 2373.
PR: 197270
Approved by: bapt
MFC after: 2 weeks
anything until the interface is assigned an address. This fixes
ipfw_nat to do the same by using an IP of INADDR_ANY instead of
aborting the nat setup if the requested interface is not yet configured.
Differential Revision: https://reviews.freebsd.org/D1539
Reviewed by: melifaro, glebius, gnn
MFC after: 1 week
This includes a new summary mode (-s) for camcontrol defects that
quickly tells the user the most important thing: how many defects
are in the requested list. The actual location of the defects is
less important.
Modern drives frequently have more than the 8191 defects that can
be reported by the READ DEFECT DATA (10) command. If they don't
have that many grown defects, they certainly have more than 8191
defects in the primary (i.e. factory) defect list.
The READ DEFECT DATA (12) command allows for longer parameter
lists, as well as indexing into the list of defects, and so allows
reporting many more defects.
This has been tested with HGST drives and Seagate drives, but
does not fully work with Seagate drives. Once I have a Seagate
spec I may be able to determine whether it is possible to make it
work with Seagate drives.
scsi_da.h: Add a definition for the new long block defect
format.
Add bit and mask definitions for the new extended
physical sector and bytes from index defect
formats.
Add a prototype for the new scsi_read_defects() CDB
building function.
scsi_da.c: Add a new scsi_read_defects() CDB building function.
camcontrol(8) was previously composing CDBs manually.
This is long overdue.
camcontrol.c: Revamp the camcontrol defects subcommand. We now
go through multiple stages in trying to get defect
data off the drive while avoiding various drive
firmware quirks.
We start off by requesting the defect header with
the 10 byte command. If we're in summary mode (-s)
and the drive reports fewer defects than can be
represented in the 10 byte header, we're done.
Otherwise, we know that we need to issue the
12 byte command if the drive reports the maximum
number of defects.
If we're in summary mode, we're done if we get a
good response back when asking for the 12 byte header.
If the user has asked for the full list, then we
use the address descriptor index field in the 12
byte CDB to step through the list in 64K chunks.
64K is small enough to work with most any ancient
or modern SCSI controller.
Add support for printing the new long block defect
format, as well as the extended physical sector and
bytes from index formats. I don't have any drives
that support the new formats.
Add a hexadecimal output format that can be turned
on with -X.
Add a quiet mode (-q) that can be turned on with
the summary mode (-s) to just print out a number.
Revamp the error detection and recovery code for
the defects command to work with HGST drives.
Call the new scsi_read_defects() CDB building
function instead of rolling the CDB ourselves.
Pay attention to the residual from the defect list
request when printing it out, so we don't run off
the end of the list.
Use the new scsi_nv library routines to convert
from strings to numbers and back.
camcontrol.8: Document the new defect formats (longblock, extbfi,
extphys) and command line options (-q, -s, -S and
-X) for the defects subcommand.
Explain a little more about what drives generally
do and don't support.
Sponsored by: Spectra Logic
MFC after: 1 week
filesystems. It differs from file(1) in that it gives machine-parseable
output, it outputs filesystem labels, doesn't get confused by other
formats metadata, and runs in Capsicum sandbox.
Differential Revision: https://reviews.freebsd.org/D1255
Relnotes: yes
Sponsored by: The FreeBSD Foundation
