old type (stty) ioctls can easily bypass locking bits.
It involves manual conversion from old ioctls to new ones,
large piece of code duplicated from tty_compat.c
after ttioctl too, because it can change t_line.
Remove (TS_CNTTB | TS_LNCH) test, it is always inherits from
old tty mode and can't be reach in currently setted mode.
old value.
Remove unnecessary check for active messages in setup SCB. This same test
would also jump to p_mesgin_done which would "ACK" an extra time possibly
confusing the target.
Tell the kernel driver whenever we send an ABORT_TAG message.
- Report valid residual byte counts. We actually pause the sequencer
when the residual is non-zero. I thought about using DMA to do this,
bus sequencer program space is tight.
- Fix embarassing off by one error in the computation of a 2's
compliment variable. This was most likely the cause of the
many problems reported with the tagged queuing code.
- Handle "MAX_SYNC" as a special case (ie we are the ones starting
the sync negotiation sequence). This was done so that the target
scratch area can be initialed to 0 offset (asyncronous transfers)
safely. The initialization to 0 (was 15) is necessary since in
some cases a Wide negotiation could run into problems if SCSIRATE
was set wrong and we went into data(in/out).
- Trim the DMA routines a little by using some procedures. Net
effect is more functionality with 3 less instructions after this
update.
- Toggle the WIDEODD bit of the DFCNTRL whenever this is not the
last SG block. It has no effect in the 8bit bus configuration,
but in the Wide configuration ensures that the overlap byte is
held in the SCSI block if the transfer is odd so it will end
up in the next SG (the correct behavior).
* to reduce the number of adapter failures. Transceiver select
* logic changed to use value from EEPROM. Autoconfiguration
* features added.
Submitted by: "Serge A. Babkin" <babkin@hq.icb.chel.su>
update what has actually been touched. This should speed up
screen access on slow hardware.
Introduced setting of "destructive" cursor size, much like
the old hardware cursor.
if (tp->t_line != 0)
test when CS_ODONE, it fails for NTTYDISC, use
if (linesw[tp->t_line].l_start != ttstart)
instead.
Reviewed by:
Submitted by:
Obtained from:
CVS:
BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
include <pci/pcivar.h> without including <sys/devconf.h> and other
drivers include <pci/pcivar.h> before including <sys/devconf.h> if
certain identifiers are defined.
The devconf headers have convoluted interdependencies. <sys/devconf.h>
includes <machine/devconf.h> which includes <pci/pcivar.h>. Most
drivers include <sys/devconf.h> so even isa drivers depend on
<pci/pcivar.h>. For similar reasons, most drivers depend on another
pci header, on an isa header and on two scsi headers.
NOT derived from the Linux code and is thus not GPL'd. It is the author's
express wish that the GPL copyrighted version be removed and this BSD copyright
version take its place. Considering our own stance on this, I'm certainly
not going to argue! [Note to NetBSD folks: You're free to grab it now :-)]
Submitted by: Mikael Hybsch <micke@dynas.se>
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
1) Supports PCI to PCI bridge devices (and tries to initialise them,
even if the BIOS is brain dead).
2) Supports shared PCI interrupts. Interrupt handlers now MUST return
'0' if they found nothing to do, '1' otherwise.
New features tested with i486 systems based on the Intel Saturn and
a DEC 4channel Ethernet card only, but expected to work on most systems.
The option PCI_REMAP has been removed !
Submitted by: Wolfgang Stanglmeier <wolf@kintaro.cologne.de>
a device specific shutdown routine for devconf. Assign the value of this
to the kern_devconf struct. Implement a device shutdown routine for if_de
that disables the device. This will stop the device from corrupting memory
after a reboot.
