Also, optimize out a mess of #if's that were duplicating work already
done by config(8). For example, if a file is marked as
"dev/sound/pci/foo.c optional pcm pci" then it's only added if pcm *and*
pci are present, so #if NPCM > 0 and #if NPCI > 0 are totally redundant.
A bit more work is still needed.
Discussed with: cg (a few weeks ago)
Without this, ioctl commands for setting formats and speeds were
essentially ignored for simplex devices until the application actually
performed a read or write.
* Make sure that both channels are set in the SB mixer code and provide a
mixer table specifically for the ess18xx which supports the extended
accuracy available on this part.
* Fix a stupid bug in ess_format() which ignored the passed-in format and
changed the hardware based on the value which was set last time. This
meant that the hardware setting was often not set correctly at all.
* Add a custom identify driver for the ESS1888 which automagically detects
and adds the device in a pseudo-PnP way. This driver also emits the magic
sequence which enables the sound hardware after a hard reset, allowing
it to work correctly for the sound hardware of a PWS 433au (and probably
all other PWS class alpha machines).
With these changes, I was able to play back simple sounds on my 433au. I
have not tested recording or any other formats other than 8bit ulaw and
16bit stereo.
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
DEB macro). There are probably quite a few other messages that warrant
a similar treatment, and many more that should be converted to plain
log messages (e.g. "WARNING: wrintr but write DMA inactive!"). Now
that I think of it, same goes for the CAM code (e.g. the famed "tagged
openings" message)
add support for Vibra16X, OPTi925, and bring in several assorted
fixes to the code and documentation.
Also present here are apm hooks so that laptops can properly
reconfigure the hardware after suspend (tested on the Libretto50).
Reviewed by: jordan
select/poll and DEVFS changes, which are limited to an include/define
in sound.h and the actual select/poll implementation in sound.c
[ This commit is blind, but the code is similar enough that there will
hopefully be no problems. ]
changes:
o rip the old select from his distribution to prevent extra pollution
o the code now uses audio dma, helps reduce clicks
o improved card support, should work in full duplex on sb16 cards
o add better voxware ioctl support pointed out by Joao Carlos Mendes
Luis <jonny@coppe.ufrj.br>
o remove an unused file that I included for more complete history
o and MANY other changes
I have personally tested this code with a CS4237 based card and an AWE32
(non-PnP). Both cards worked fine in 8bit and 16bit mode.
