based on the destination sleep state. Add a method to restore the old
state on resume. This is needed for the case of suspending to a very low
state disabling a GPE (i.e. S4), resuming, and then suspending to a higher
state (i.e. S3). This case should now keep the proper GPEs enabled.
device can wake the system. For example:
dev.root0.nexus0.acpi0.acpi_lid0.wake: 1
dev.root0.nexus0.acpi0.acpi_button0.wake: 1
dev.root0.nexus0.acpi0.pcib0.wake: 0
dev.root0.nexus0.acpi0.sio0.wake: 0
been developed for use with FreeBSD, version 4.8 and later.
Submitted by: Hema Joyce
Reviewed by: Prafulla Deuskar
Approved by: Prafulla Deuskar
MFC after: 1 week
subsystem lock to avoid tripping over an assertion regarding whether
the lock is held or not. This is likely to be the cause of a panic
tripped over by Andrea Campi.
acpi_wake_init:
Evaluate _PRW and set the GPE type
acpi_wake_set_enable:
Enable or disable a device's GPE.
acpi_wake_sleep_prep:
Perform any last-minute changes to the device to prepare it for
entering the given sleep state.
Also, walk the entire namespace when transitioning to a sleep state,
disabling any GPEs which aren't appropriate for the given state. Transition
acpi_lid and acpi_button to the new API.
This clears the way for non-ACPI-aware devices to wake the system (i.e.
modems) and fixes a problem where systems power up after shutdown when a
GPE is triggered.
In particular, disabling it was likely to break configurations
involving ng_vlan(4) since the latter couldn't control
the parent's VLAN_MTU in the way vlan(4) did.
Pointed out by: ru
does not reliably prevent the triggering of interrupts for all supported
configurations. Thus, the FIFO size probe could cause an interrupt,
which could lead to an interrupt storm in the shared interrupt case.
To prevent this, change ns8250_bus_probe() to use the overflow bit in
the line status register instead of the RX ready bit in the interrupt
identification register to detect whether the FIFO has filled up.
This allows us to clear all bits in the interrupt enable register during
the probe, which should prevent interrupts reliably.
Additionally, the detected FIFO size may be a bit more accurate, because
the overflow bit is only set when the FIFO did actually fill up, while
interrupts would trigger a bit early.
Reviewed and tested on a lot of hardware by: marcel
struct vmspace is freed from cpu_sched_exit() to pmap_release().
This has the advantage of being able to rely on MI code to decide
when a free should occur, instead of having to inspect the reference
count ourselves.
At the same time, turn the per-CPU vmspace pointer into a pmap pointer,
so that pmap_release() can deal with pmaps exclusively.
Reviewed (and embrassing bug spotted) by: jake
gmon and struct gmonhdr was originally just to represent the kernel
(profiling) clock frequency and it remains poorly suited to representing
the frequencies of fast counters like the TSC. It broke a year or two
ago. This quick fix keeps it working for another year or month or two
until TSC frequencies can exceed 2^32, by dividing the frequency by 2.
Dividing the frequency by 4 would work for a little longer but would
lose a little too much precision.
Fixed profiling of trap, syscall and interrupt handlers and some
ordinary functions, essentially by backing out half of rev.1.106 of
i386/exception.s. The handlers must be between certain labels for
the purposes of profiling, and this was broken by scattering them in
separately compiled .s files, especially for ordinary functions that
ended up between the labels. Merge the files by #including them as
before, except with different pathnames and better comments and
organization. Changes to the scattered files are minimal -- just
move the labels to the file that does the #includes.
This also partly fixes profiling of IPIs -- all IPI handlers are now
correctly classified as interrupt handlers, but many are still missing
mcount calls.
vm86bios.s is included as before, but it is now between the labels for
interrupt handlers again, which seems to be wrong since half of it is
for a non-interrupt handler.
converts miidevs to a .h file, so rename to reflect that.
The usb and pccard versions have also been renamed and will be hooked
into the build system shortly (I've made the conversion in my p4
tree).
process is a non-prison root. The security.jail.allow_raw_sockets
sysctl variable is disabled by default, however if the user enables
raw sockets in prisons, prison-root should not be able to interact
with firewall rule sets.
Approved by: rwatson, bmilekic (mentor)
WRT manipulating capabilities of the parent interface:
- use ioctl(SIOCSIFCAP) to toggle VLAN_MTU (the way that was done
before was just wrong);
- use the right order of conditional clauses to set the MTU fudge
(that is logically independent from toggling VLAN_MTU.)
This splits the driver into a bus-independant backend, plus bus-specific
frontends. The old pcf(4) (i386/ISA) frontend is now in pcf_isa.c, the
frontend in envctrl.c is for sparc64/Ebus2 (Sun device name: SUNW,envctrl
from Sun E450 machines). More frontends are expected to appear in future.
This is not yet ready for public consumption, but it basically works.
Nicolas will bring over his ISA-specific fixes soon.
Reviewed by: nsouch
1. Contrary to the Single Unix Specification our implementation of
munlock(2) when performed on an unwired virtual address range has
returned an error. Correct this. Note, however, that the behavior
of "system" unwiring is unchanged, only "user" unwiring is changed.
If "system" unwiring is performed on an unwired virtual address
range, an error is still returned.
2. Performing an errant "system" unwiring on a virtual address range
that was "user" (i.e., mlock(2)) but not "system" wired would
incorrectly undo the "user" wiring instead of returning an error.
Correct this.
Discussed with: green@
Reviewed by: tegge@
* Add calls to AcpiSetGpeType. We use wake/run as the type for lid and
button switches since wake-only causes Thinkpads to immediately wake on
the second suspend. Note that with wake/run, some systems return both
wake and device-specific notifies so we don't register for system notifies
for lid and button switches.
* Remove the hw.acpi.osi_method tunable since it is not needed.
* Always print unknown notifies for all types.
* Add more cleanup for the EC if it fails to attach.
* Use the GPE handle now that we parse it. This allows GPEs to be defined
in AML GPE blocks.
* Always use ACPI_NOT_ISR since it's ok to acquire a mutex in our thread
which processes queued requests.
in the various pci specifications as readonly. vendor, subvendor,
device and subdevice are required to be loaded in hardware by some
means that isn't the system BIOS or other system software (although
some devices do have ways of accomplishing this). class and subclass
are defined to be read-only in section 6.2.1 (v2.2). Apart from the
status register, which we weren't touching, these are the only
read-only registers I could find in the 2.2 spec.
progif is also defined as being read-only in section 6.2.1. However,
the PCI IDE programming document specifically states that some of the
bits are read/write. Since we may have to restore registers before we
have a driver attached, go ahead and restore this one byte when
transitioning between D3 and D0.
The PCI spec also says that writes to reserved and unimplemented
registers must be completed normally. It makes no statements about
writes to read-only registers, so be as conservative as possible,
while covering the exception to the rule that is documented in a
subpart of the standard.
Requested by: socttl
polarity rather than assuming that level triggered IRQs use active low and
edge triggered IRQs use active high. Both the MultiProcessor 1.4
and ACPI 2.0 Specifications state in their examples that level triggered
EISA IRQs are active low, but in practice they seem to be active high.
Reported by: Nik Azim Azam nskyline_r35 at yahoo dot com
ordinary functions, essentially by backing out half of rev.1.115 of
amd64/exception.S. The handlers must be between certain labels for
the purposes of profiling, and this was broken by scattering them in
separately compiled .S files, especially for ordinary functions that
ended up between the labels. Merge the files by #including them as
before, except with different pathnames and better comments and
organization. Changes to the scattered files are minimal -- just
move the labels to the file that does the #includes.
This also partly fixes profiling of IPIs -- all IPI handlers are now
correctly classified as interrupt handlers, but many are still missing
mcount calls.
mechanism so that early processing on mbufs can be performed before
a context switch to the NFS server threads. Because of this, if
the socket code is running without Giant, the NFS server also needs
to be able to run the upcall code without relying on the presence on
Giant. This change modifies the NFS server to run using a "giant
code lock" covering operation of the whole subsystem. Work is in
progress to move to data-based locking as part of the NFSv4 server
changes.
Introduce an NFS server subsystem lock, 'nfsd_mtx', and a set of
macros to operate on the lock:
NFSD_LOCK_ASSERT() Assert nfsd_mtx owned by current thread
NFSD_UNLOCK_ASSERT() Assert nfsd_mtx not owned by current thread
NFSD_LOCK_DONTCARE() Advisory: this function doesn't care
NFSD_LOCK() Lock nfsd_mtx
NFSD_UNLOCK() Unlock nfsd_mtx
Constify a number of global variables/structures in the NFS server
code, as they are not modified and contain constants only:
nfsrvv2_procid nfsrv_nfsv3_procid nonidempotent
nfsv2_repstat nfsv2_type nfsrv_nfsv3_procid
nfsrvv2_procid nfsrv_v2errmap nfsv3err_null
nfsv3err_getattr nfsv3err_setattr nfsv3err_lookup
nfsv3err_access nfsv3err_readlink nfsv3err_read
nfsv3err_write nfsv3err_create nfsv3err_mkdir
nfsv3err_symlink nfsv3err_mknod nfsv3err_remove
nfsv3err_rmdir nfsv3err_rename nfsv3err_link
nfsv3err_readdir nfsv3err_readdirplus nfsv3err_fsstat
nfsv3err_fsinfo nfsv3err_pathconf nfsv3err_commit
nfsrv_v3errmap
There are additional structures that should be constified but due
to their being passed into general purpose functions without const
arguments, I have not yet converted.
In general, acquire nfsd_mtx when accessing any of the global NFS
structures, including struct nfssvc_sock, struct nfsd, struct
nfsrv_descript.
Release nfsd_mtx whenever calling into VFS, and acquire Giant for
calls into VFS. Giant is not required for any part of the
operation of the NFS server with the exception of calls into VFS.
Giant will never by acquired in the upcall code path. However, it
may operate entirely covered by Giant, or not. If debug.mpsafenet
is set to 0, the system calls will acquire Giant across all
operations, and the upcall will assert Giant. As such, by default,
this enables locking and allows us to test assertions, but should not
cause any substantial new amount of code to be run without Giant.
Bugs should manifest in the form of lock assertion failures for now.
This approach is similar (but not identical) to modifications to the
BSD/OS NFS server code snapshot provided by BSDi as part of their
SMPng snapshot. The strategy is almost the same (single lock over
the NFS server), but differs in the following ways:
- Our NFS client and server code bases don't overlap, which means
both fewer bugs and easier locking (thanks Peter!). Also means
NFSD_*() as opposed to NFS_*().
- We make broad use of assertions, whereas the BSD/OS code does not.
- Made slightly different choices about how to handle macros building
packets but operating with side effects.
- We acquire Giant only when entering VFS from the NFS server daemon
threads.
- Serious bugs in BSD/OS implementation corrected -- the snapshot we
received was clearly a work in progress.
Based on ideas from: BSDi SMPng Snapshot
Reviewed by: rick@snowhite.cis.uoguelph.ca
Extensive testing by: kris
This change is possible since all the relevant drivers have been
fixed to set if_capenable properly. The field if_capabilities tracks
supported capabilities, which may be disabled administratively.
Inheriting checksum offload support from the parent interface isn't
that easy because the checksumming capabilities of the parent may be
toggled on the fly. Disable the code for now.
Kernel profiling for amd64's (normal and high resolution) should now
compile and work as (un)well as on i386's. It works better than user
profiling because:
- it uses _cyg_profile_func_*() instead of .mcount(), so it doesn't suffer
from gcc misspelling .mcount as mcount.
- it doesn't neglect saving %rax in .mcount().
The SMP case hasn't been tested. The high resolution subcase of this uses
the i8254, and as on i386's, the locking for this is deficient and the
i8254 is too inefficient. The acpi timer is also too inefficient.
- perfmon headers must be avoided until perfmon is supported.
- all call-used registers including return registers must be preserved
by .mcount(), etc., not quite as in profile.h. __cyg_profile_func_*()
don't require this, but they are (mis)implemented as aliases for
.mcount(), etc. so they preserve the registers.
- i386 ifdefs related to perfmon have not been adjusted yet.
amd64 as necessary. This is routine, except:
- the FAKE_MCOUNT($bintr) in doreti was missing the '$'. This gave a
a garbage address made up of padding bytes (with the nop byte 0x90 as
the MSB) instead of the intended address of bintr. This accidentally
worked on i386's because (0x90 << 24) is close enough to bintr, but
it doesn't work on amd64's because (0x90 << 56) is much further away
from bintr.
- the FAKE_MCOUNT($btrap) in calltrap was similarly broken. It hasn't
been needed since FreeBSD-1, so just delete it.
and high resolution profiling of interrupt handlers. The adjustments
are routine once the magic stack offset 13*4 is decoded to be TF_RIP
(there were originally more types of stack frames so using TF_EIP for
one of them wouldn't have been much simpler).
Removed garbage comments attached to some of the FAKE_MCOUNT()s.
that the usual macro for "ret" hides the detail of calling .mexitcount
before returning.
Fixed missing call to .mexitcount in lgdt(). This was missing on
i386's, mainly because lgdt() uses lret[q] insted of ret. This is
very unimportant since lgdt() is not (normally?) called until after
profiling is initialized.
in all USB ethernet drivers. The qdat structure contains a pointer
to the interface's struct ifnet and is used to process incoming
packets, so simultaneous use of two similar devices caused crashes
and confusion.
The if_udav driver appeared in the tree since Daan's PR, so I made
similar changes to that driver too.
PR: kern/59290
Submitted by: Daan Vreeken <Danovitsch@Vitsch.net>
MFNetBSD 1.177; author: toshii
Use the correct wValue to get hub desriptors.
Also, make wValue checks of root hub codes less strict.
MFNetBSD 1.178: author: martin
Interrupt descriptors might become invalid while being processed in
uhci_check_intr - so remember their next pointer before calling it.
Patch provided by Matthew Orgass in PR kern/24542.
Obtained from: NetBSD
KERN_PROC_SESSION option which had been previously defined but
never implemented.
PR: bin/65803 (a very tiny piece of the PR)`
Submitted by: Cyrille Lefevre
return value for BUS_READ_IVAR and thus don't generate the proper NULL
in cases where a device (i.e. on PCI) does not have a handle.
Found by: peadar, tjr
identifiers, to openfirmio.h as OFIOCMAXNAME, so programs can use it
for buffer sizes etc.
Note: Although this is only a rough upper limit to make the code more
robust and to prevent the allocation of ridiculous amounts of memory,
the current limit of one page (8191 + '\0' in openfirm_getstr()) still
appears a bit high. The maximum length of OFW property names is 31.
I didn't find a maximum length for the device identifiers in the OFW
documentation but it certainly is much smaller than 8191, too.
- Enable the OFIOCSET ioctl, i.e. move it out from under #if 0.
- Don't use openfirm_getstr() for the property value in OFIOCSET, there
are also properties whose values aren't strings and it makes sense to
use a different maximum length for property values than OFW_NAME_MAX/
OFIOCMAXNAME. The maximum accepted property value is defined in
openfirmio.h as OFIOCMAXVALUE (currently the maximum size of the value
of the nvramrc property).
- Make OFIOCSET not return EINVAL when OF_setprop() returns a different
length for the written value than it was told to write, this is normal
for the text string values of the properties in the OFW /options node.
Instead, only return EINVAL if OF_setprop() returned -1 (value could
not be written or property could not be created). Add a comment about
the specialty of the OFW /options node.
- Make OFIOCSET return the length of the written value returned by
OF_setprop(), just like OF_getprop() does. Quite useful, at least for
debugging.
Reviewed by: tmm
is being turned off, or else TCP/IP will keep assigning the job to us.
Drivers themselves should consult if_capenable, not if_hwassist--the
latter is for the TCP/IP stack.
being that PHYS_TO_VM_PAGE() returns the wrong vm_page for fictitious
pages but unwiring uses PHYS_TO_VM_PAGE(). The resulting panic
reported an unexpected wired count. Rather than attempting to fix
PHYS_TO_VM_PAGE(), this fix takes advantage of the properties of
fictitious pages. Specifically, fictitious pages will never be
completely unwired. Therefore, we can keep a fictitious page's wired
count forever set to one and thereby avoid the use of
PHYS_TO_VM_PAGE() when we know that we're working with a fictitious
page, just not which one.
In collaboration with: green@, tegge@
PR: kern/29915
and improved some comments). Also, made the documented {f,s}uword()
functions the standard entry points and the undocumented {f,s}uword64()
functions alternative entry points, like {f,s}uword32() for i386's. The
bitrot in the comments was a little larger here -- there are new undocumented
32-bit sub-word functions, not just renaming of 16-bit functions from
documented ones to undocumented ones.
of not clearing the flags for execv() syscall will result that a new
program runs in KSE thread mode without enabling it.
Submitted by: tjr
Modified by: davidxu
fixes was applicable to HEAD, originally it was thought this
should only be done in RELENG_4. Implement IO_INVAL in the vnode
op for writing by marking the buffer as "no cache". This fix
has already been applied to RELENG_4 as Rev. 1.65.2.15 of
ufs/ufs/ufs_readwrite.c.
Reviewed by: alc, tegge
Split the baby. For idepci devices, now both legacy mode bits need
not be set. We can run an idepci in a split mode. However, it only
works better than before, not works. It works better in that when one
device is legacy and the other isn't and disabled, we now operate
correctly.
sos submitted a version of this patch.
subclass, progif and revid. While these are typically read
only fields, they aren't always read-only. progif is writable
for ata devices, for example. It does no harm when they are
read only, and helps when they aren't.
to try to allocate things on my parent can be taken out. It duplicates code.
Also, add comment about why the power state stuff is here (type 2
devices don't participate in the power state save/restore due to
larger Bx issues).
chattiness was left in for debugging, but now that nearly all of the
problems relating to the changes have been fixed, it is only annoying. It
is still available via bootverbose.
Prodded by: jhb
