too small panics on PAE machines which have odd > 4GB sizes (4.5 gig
would render a 20MB of KVA for kmem_map instead of 200MB).
Submitted by: John Cagle <john.cagle@hp.com>, jeff
Reviewed by: jeff, peter, scottl, lots of USENIX folks
about the driver version in case of an error report. It conflicts with
some other variable of the same name that has been added to the kernel
just recently and there haven't been any bug reports for quite some
time now, anyway ...
is currently executing when we try to remove it in exit1(). Without this,
it was possible for the callout to bogusly rearm itself and eventually
refire after the process had been free'd resulting in a panic.
PR: kern/51964
Reported by: Jilles Tjoelker <jilles@stack.nl>
Reviewed by: tegge, bde
curthread. Unlike td_flags, this field does not need any locking.
- Replace the td_inktr and td_inktrace variables with equivalent private
thread flags.
- Move TDF_OLDMASK over to the private flags field so it no longer requires
sched_lock.
userland, and the kernel. In the kernel by way of the 'ident[]' variable
akin to all the other stuff generated by newvers.sh. In userland it is
available to sysctl consumers via KERN_IDENT or 'kern.ident'. It is exported
by uname(1) by the -i flag.
Reviewed by: hackers@
second and equalizing the load between the two most imbalanced CPU. This
is intended to clear up long term load imbalances that would not be handled
by the 'pull' method in sched_choose().
- Pull out some bits of sched_choose() into a kseq_move() function that moves
an arbitrary thread from one kseq to another.
adding it to the nice tables. Therefore, in kseq_add_nice, we should
keep in mind that the load will be 1 if we are the only thread, and not
0.
- Assert that the sched lock is held in all the appropriate places.
- Increase the scope of the sched lock in sched_pctcpu_update().
- Hold the sched lock in sched_runnable(). It is not held by the caller.
ia64-specific.
- When trying to re-route interrupts, don't change cfg->intline if the
re-route fails by returning an invalid vector. This fixes machines
without any way of routing interrupts such as older PC's without a
$PIR table.
We do not currently write the new intline value back to the hardware, but
we should. That will likely be added in a later commit.
the caller assumes this to not happen by means of performing an
indirection without checking the return value. Add KASSERTs to
force a kernel with INVARIANTS to panic. This is a short-term
measure. The pmap code is scheduled to be overhauled.
to deliver a signal and the RSE backing store has been exhausted or
the backing store pointer has been clobbered, we need to make sure
we call userret() and do_ast() when we exit from trap(). Not adjusting
the local variable 'user' in this case will prevent the faulty process
from being terminated and we end up in an infinite fault repetition.
Faulty process provided by: bento
if it was already enabled. We don't want to set it
when it shouldn't be set, we just don't want to
inadvertantly turn it off. This should fix a recent
report of the aic7xxx driver repeatedly complaining of
"unexpected busfree while idle" in one configuration.
successfully mapping our registers. This
avoids the disabling of memory mapped I/O
just because some other driver probe happened
to touch our registers.
This drive delays going async after receiving a WDTR
message. We now send an SDTR message after a WDTR even
if our goal is to go async. This should work even for
confused devices.
If we get an unexpected busfree when attempting a WDTR
or SDTR, only set the goal negotiation parameters we were
trying to negotiate to off. This means that should a WDTR
message fail, we will still try an SDTR if our goal is
non-async.
Fix a few more places where we were looking at goal.period
instead of goal.offset for determining if we should be
negotiating sync. This should not have any impact on
our behavior, but the offset is more definitive and should
be used.
aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
aic7xxx.c:
aic7xxx.h:
aic7xxx_pci.c:
Switch ah?_reset() to take an additional "reinit" argument.
Use this instead of init_level to determin if the chip
should be fully reinitialized after a chip reset. This
is required so that ah?_shutdown() can reset the chip
without side-effects.
aic79xx.c:
Implement ahd_suspend() and ahd_resume().
aic7xxx.c:
Change ahc_loadseq() to *not* restart the sequencer.
This brings the loadseq behavior in line with that
of the 7902 driver and also simplifies the init routine.
Correct the resume routine to enable interrupts and
restart the sequencer.
