And build libdl unconditionally. All supported FreeBSD linkers accept
-F / --filter so there is no need to test for support.
Discussed with: kib
Sponsored by: The FreeBSD Foundation
it appropriately when building share/ctypedef and share/colldef.
This makes the resulting locale data in EL->EB (amd64->powerpc64) cross
build and in the native EB build match. Revert the changes done to libc
in r308170 as they are no longer needed.
PR: 231965
Reviewed by: bapt, emaste, sbruno, 0mp
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D17603
Rather then combining hardlink creation for the geom(8) binary with
shared library build, move libraries to src/lib/geom so they are
built and installed normally. Create a common Makefile.classes
which is included by both lib/geom/Makefile and sbin/geom/Makefile
so the symlink and libraries stay in sync.
The relocation of libraries allows libraries to be build for 32-bit
compat. This also reduces the number of non-standard builds in
the system.
This commit is not sufficent to run a 32-bit /sbin/geom on a 64-bit
system out of the box as it will look in the wrong place for libraries
unless GEOM_LIBRARY_PATH is set appropriatly in the environment.
Reviewed by: bdrewery
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15360
kgdb now handles kernel module state internally, so the asf tool serves
no purpose.
PR: 229046
Reviewed by: brooks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15827
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
has been switched to libedit long ago, libreadline was built as an
internallib for a while and kept only for gdbtui which was broken using
libreadline.
Since gdb has been mostly deorbitted in all arches, gdbtui was only installed
on arm and sparc64, given it has been removed, gdb has been switched to use
libedit, no consumers are left for libreadline. Thus this removal
only installed on arm and sparc64.
It is the only bits that keeps us having libreadline in base
The rest of gdb can be switched to libedit and will be in another
commit
xlint is currently a fossil. We have much more useful and alive tools
to do now what xlint did twenty years ago.
I did not cleared some stuff which makes lint operational, in
sys/x86/include and sys/sys, but I might do it as followup. The
x86/include/ucontext.h and _types.h hacks made to please lint was the
main reason for my initial proposal to classify xlint as obsolete and
to remove it.
Also I do not intend to clear sccs ids.
Reviewed by: bapt, brooks, emaste, jhb, pfg
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D13015
This problem was caused by r325329 and r325350.
For the release(7) targets, some will run mm-mtree.sh which itself runs make
with a MAKEOBJDIRPREFIX. The execution of that script leaks OBJROOT,
MAKEOBJDIR, and MAKELEVEL=1 in the environment. This causes the mm-mtree makes
to not do some basic setup of OBJROOT and only use this special
MAKEOBJDIRPREFIX case which fails to empty out MAKEOBJDIRPREFIX for further
nested makes, such as a tree walk. If that tree walk sets OBJROOT/OBJTOP such
as r325329 is doing, then the wrong OBJDIRs end up being used due to the
unemptied MAKEOBJDIRPREFIX being preferred over the proper MAKEOBJDIR.
Pointyhat to: bdrewery
Sponsored by: Dell EMC Isilon
This still keeps the reduced MAKEOBJDIRPREFIX (SRCTOP) redundancy
removed in the OBJDIR, but now keeps all early phase objects
in the same directory rather than split per phase.
The problem of splitting per phase is that later phases want to link in
libraries from earlier phases and base their location on ${OBJTOP}.
Pointyhat to: bdrewery
Reported by: mjoras, Mark Millard
Sponsored by: Dell EMC Isilon
It was supposed to provide a recovery mechanism against bugs in procfs's
long deprecated tracing capabilities.
Remove the tool as a prerequisite to axing the kernel side.
The tracing facility to use is ptrace(2).
MFC after: 2 weeks
in favor of just rendering the manpage instead of relying on pre-formatted
catpages. Note, this does not impede the ability to use existing catpages,
it just removes the utility to generate them.
Reviewed by: imp, allanjude
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12317
Copy the most important test cases from OpenBSD's corresponding
src/regress/sbin/pfctl, those that run pfctl on a test input file and check
correctness of its output. We have also added some new tests using the same
format.
The tests consist of a collection of input files (pf*.in) and
corresponding output files (pf*.ok). We run pfctl -nv on the input
files and check that the output matches the output files. If any
discrepancy is discovered during future development in the source
tree, we know that a regression bug has been introduced into the tree.
Submitted by: paggas
Sponsored by: Google, Inc (GSoC 2017)
Differential Revision: https://reviews.freebsd.org/D11322
This is useful for having directories behave differently depending
on the phase - such as enabling SUBDIR_PARALLEL or disabling
redundant building of library directories already done by
earlier 'make _libraries'.
Sponsored by: Dell EMC Isilon
The exit status will be 124, as the timeout(1) utility uses.
Reviewed by: jilles
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D9697
Move cxgbetool from tools/tools to usr.sbin. Compile and install it on
platforms where cxgbe(4) is built by default. Knobs (WITH_CXGBETOOL and
WITHOUT_CXGBETOOL) have been added so that the user can override the
default setting.
Reviewed by: ngie@, gnn@, bdrewery@
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D9854
