add some logging functionality which I find very useful.
'set debug link' will record just link up/down and address assignments.
'set debug connect' will record the entire chat dialog
'set debug carrier' will record just chat lines including 'CARRIER'
(so that I can be sure I'm getting a 28.8 line).
There was a global change required to permit LogPrintf to take a bit
mask instead of a bit position value (to permit logging some events
on either of two flags, so that no change in 'set debug lcp' would
result from the code supporting 'link'. Thus the diffs are rather
long for such a small change. The man page is also touched.
Oh, and there was a slight syntax problem in route.c
Reviewed by: phk
Submitted by: Tony Kimball <alk@Think.COM>
2) Improve on-line help subsystem
3) Make 'term' mode works even carrier dropped (old code
close line forever here)
4) Make 'term' mode 8bit clean.
5) Improve manual page
6) #ifdef DEBUG diagnostic about missing optional files.
7) Don't put interactive dialing info to logfile
A settable redial timer helps to avoid the problem where both ends
of a link want to dial at the same time and the line winds up busy
for both ends. The process id is logged in /var/run/PPP.system where
system is the name of the called system. When both ends of a link
are running in demand dial mode, you need an easy way to get the pid
of the ppp on the called end so it can be killed and re-started with
-direct or pppd started to handle the incoming ppp session.
2. Add secret description for "set timeout" to man.
Reviewed by: Atsushi Murai <amurai@spec.co.jp>
Submitted by: John Capo <jc@irbs.com>
2. Optimize ModemQlen.
3. Sending ProtoReject for Unknow protocol (i.e. IPX)
4. Avoid select looping by reading tun under the high system load.
5. Adding Local version String for maintenance.
6. Just more speak rather silent ignore if you type invalid key words.
The first problem I found was that descriptor 0 was being closed.
This happens because the modem variable is set to 0 to indicate
that it is not valid but there are not enough tests for the modem
variable being 0. You can see where I have done this in the patch.
Code in OpenModem() dups the modem descriptor if it is < 3. Once
this happened the modem was always open and an incomming call would
have getty and ppp reading the modem.
Descriptor 1 is closed when the quit command was executed from a
telnet connection. The next modem open returns descriptor 1
and this gets duped leaving the modem always open again.
The modem was not being closed when the connection dropped or was
closed from the other end. The UUCP lock was also not removed if
the modem could not be opened.
Reviewed by: Atsushi Murai <amurai@spec.co.jp>
Submitted by: John Capo <jc@irbs.com>
o Supporting SYNC SIO device (But need a device driver)
- add "set speed sync"
o Fixing bug for Predictor-1 function.
o Add new parameter that re-sent interval for set timeout commands.
o Improving RTT (Round Trip Time) and reducing processor time.
- Previous Timer service was using polling, and now using
SIGALRM ;-)
- A 0.94beta2 will not work correctly....
-- Follows are additinal feature not including 0.94beta2
o Support Proxy ARP
- add "enable/disable proxy" commands
o Marging common routine in CHAP/PAP.
o Enhancing LCP/IPCP log information.
o Support local Authfication connection on port 300x and tty.
- You can set up pair of your "hostname -s" and
password in ppp.secret. if either ppp.secret file nor
your hostname line don't exist, It will notify a message
and working as same as previous version.(Backword compatibility)
- If you did set up them, It's allow connection but nothing to do
except help and passwd command.
- add "passwd yourpasswd" commands
o Support afilter - keep Alive filter that a packet can send/receiving
according to ifilter/ofilter but doesn't count it as preventing idle
timer expires.
- Same syntax of other filters.
o Fixing bugs reported by current user for previous one. Thanks !!
Reviewed by: Atsushi Murai (amurai@spec.co.jp)
