- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
already defined. This allows for cross building to work because we
need to lie to make to tell it to use the target names rather than the
host names.
This should have no effect on either architecture. I've confirmed
that the intel build by make buildworld's for the past 3 months.
to an architecture-specific value defined in <machine/elf.h>. This
solves problems on large-memory systems that have a high value for
MAXDSIZ.
The load address is controlled by a new macro ELF_RTLD_ADDR(vmspace).
On the i386 it is hard-wired to 0x08000000, which is the standard
SVR4 location for the dynamic linker.
On the Alpha, the dynamic linker is loaded MAXDSIZ bytes beyond
the start of the program's data segment. This is the same place
a userland mmap(0, ...) call would put it, so it ends up just below
all the shared libraries. The rationale behind the calculation is
that it allows room for the data segment to grow to its maximum
possible size.
These changes have been tested on the i386 for several months
without problems. They have been tested on the Alpha as well,
though not for nearly as long. I would like to merge the changes
into 3.1 within a week if no problems have surfaced as a result of
them.
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
* Move the user stack from VM_MAXUSER_ADDRESS to a place below the 32bit
boundary (needed to support 32bit OSF programs). This should also save
one pagetable per process.
* Add cvtqlsv to the set of instructions handled by the floating point
software completion code.
* Disable all floating point exceptions by default.
* A minor change to execve to allow the OSF1 image activator to support
dynamic loading.
#include <ieeefp.h>
to access these functions instead of the i386 specific
#include <machine/floatingpoint.h>
Submitted by: Hidetoshi Shimokawa <simokawa@sat.t.u-tokyo.ac.jp>
- created internal names for fixed-size integral types, like __int32_t. They
will be used to make several headers self-sufficient.
- <stdlib.h> don't include <machine/types.h> anymore.
- created <sys/inttypes.h>, which can be used as <inttypes.h>.
- declaration of uoff_t and ufs_daddr_t moved to <sys/types.h>.
Reviewed by: bde
alpha, operations involving non-finite numbers or denormalised numbers
or operations which should generate such numbers will cause an arithmetic
exception. For programs which follow some strict code generation rules,
the kernel trap handler can then 'complete' the operation by emulating
the faulting instruction.
To use software completion, a program must be compiled with the arguments
'-mtrap-precision=i' and '-mfp-trap-mode=su' or '-mfp-trap-mode=sui'.
Programs compiled in this way can use non-finite and denormalised numbers
at the expense of slightly less efficient code generation of floating
point instructions. Programs not compiled with these options will receive
a SIGFPE signal when non-finite or denormalised numbers are used or
generated.
Reviewed by: John Polstra <jdp@polstra.com>
structure for the alpha. These give extra information about some
signals (such as SIGSEGV) and should be compatible with Digital Unix.
Submitted by: jdp
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
installed.
Remove cpu_power_down, and replace it with an entry at the end of the
SHUTDOWN_FINAL queue in the only place it's used (APM).
Submitted by: Some ideas from Bruce Walter <walter@fortean.com>
independent elf loader and have access to kld modules. Jordan and I were
not sure how to create boot floppies, and the things we tried just made
SRM laugh in our faces - but it was upset at boot1 which was not touched
by these changes. Essentially this has been untested. :-(
What this does is to steal the last three slots from the nine spare longs
in the bootinfo_v1 struct to pass the module base pointer through.
The startup code now to set up and fills in the module and environment
structures, hopefully close enough to the i386 layout to be able to use
the same kernel code. We now pass though the updated end of the kernel
space used, rather than _end. (like the i386).
If this does not work, it needs to be beaten into shape pronto. Otherwise
it should be backed out before 3.0.
Pre-approved in principle by: dfr
routines are necessary to allow the use of certain types of hardware on
the alpha, particularly a Myrinet card.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
and set_regs() but for the floating point register state. The code
is stolen from procfs_machdep.c, and moved out of there into
machdep.c.
These functions are needed for generating ELF core dumps.
the relevant characteristics of the native machine, for building
and checking Elf_Ehdr structures.
Add structures to represent ELF "note" headers. Add defines for the
note types used in ELF core files.
standard places ("/etc/objformat", ${OBJFORMAT}, argv) for an
indication of the user's preferred object file format. This
consolidates some code that was starting to be duplicated in more
and more places.
Use the new function in ldconfig.
Note: I don't think that gcc should use getobjformat(), even though
it could. The compiler should limit itself to functions that are
widespread, to ease porting and cross-compilation.
Add some overflow checks to read/write (from bde).
Change all modifications to vm_page::flags, vm_page::busy, vm_object::flags
and vm_object::paging_in_progress to use operations which are not
interruptable.
Reviewed by: Bruce Evans <bde@zeta.org.au>
* Support for AlphaStation 200, 250, 255, 400
* Untested support for UDB, Multia, AXPpci33 (Noname)
* Support for Personal Workstation 433a/433au, 500a/500au, 600a/600au (Miata)
* Some minor fixes and improvements to interrupt handling.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu> (AS200, Miata)
Obtained from: NetBSD (some code for AS200, Miata, Noname)
hopefully become a portable driver usable by all architectures. The api
support files have had to be copied to sys/alpha/include since userland
programs expect to find them in <machine/*.h>.
All the revision history of the i386 syscons has been retained by a
repository copy.
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
