Add support for 4k sector GELI encrypted partitions to the bootloader
This is the default created by the installer
Because the IV is different for each sector, and the XTS tweak carries forward you can not decrypt a partial sector if the starting offset is not 0
Make boot2 and the loader read in 4k aligned chunks
Reviewed by: ed, oshogbo
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D5820
a child of it. This is done in conformity with Linux dts files and
as preparation for rework of BCM2836 interrupt controller for INTRNG.
Reviewed by: gonzo
Differential Revision: https://reviews.freebsd.org/D5807
to the boot.netif.mtu env var, which will be picked up by pre-existing code
in nfs_mountroot() and used to configure the interface accordingly.
This should bring the same functionality when the bootp/dhcp work is done
by loader(8) as r297150 does for the in-kernel BOOTP case.
The following pheripherals are supported: UART, MMC, AHCI, EHCI, PCIe, I2C,
PMIC, GPIO, CPU temperature and clock.
Note: The PCIe driver is pure mash at this moment. It will be reworked
immediately when both D5237 and D2579 enter the current tree.
After ARM_INTRNG introduction, MPIC code needed several modifications:
- IRQ resource and its handler added
- several DEVMETHODs of INTRNG interface implemented
- defines enhanced to ensure code compiles as well for AXP as for A38X
- added dummy MSI_IRQ, ERR_IRQ defines for Armada38x
- MPIC driver was added to files.armada38x, ARM_INTRNG option enabled in
kernconf file and regs of MPIC corrected in dts file.
Instead of modifying Armada38X DTS, offsets to CPU registers defined in
driver were changed. That required restoring 'reg' property of mpic node
in ArmadaXP to state compliant with Linux DTS.
Additionally, required ARM_INTRNG definitions were added to mv_common.c.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian, andrew, ian, skra
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5030
Both objdump and nm are equally capable of reporting undefined symbols.
This gets us a step closer to building without binutils as we have an nm
implementation from ELF Tool Chain.
Reviewed by: bdrewery
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5613
Until now, ubldr has been trying to locate the U-Boot API using a hint
address (U-Boot's current stack pointer), aligning it to 1MiB and going
over a 3MiB (or 1MiB in case of MIPS) memory region searching for a
valid API signature.
This change introduces an alternative way of doing this, namely the
following:
- both U-Boot's bootelf and go commands actually pass argc and argv to
the entry point (e.g., ubldr's start function, but they should also
be passed over to main() transparently)
- so, instead of trying to go and look for a valid API signature, we
look at the parameters passed to main()
- if there's an option '-a' with argument, which is a valid hexadecimal
unsigned long number (x), we try to verify whether we have a valid
API signature at address x. If so - we use it. If not - we fallback
to the original way of locating the API signature.
The U-Boot change, which causes the API structure address to be
exported as an environment variable, was committed to mainline U-Boot
as commit 22aa61f707574dd569296f521fcfc46a05f51c48
Reviewed by: andrew, adrian
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5492
the boot loader should not skip over these anymore while loading images.
Otherwise the kernel can still panic when it doesn't find the .eh_frame
section belonging to the .rela.eh_frame section.
Unfortunately this will require installing boot loaders from sys/boot
before attempting to boot with a new kernel.
Reviewed by: kib
MFC after: 2 weeks
X-MFC-With: r296419
(32 and 64-bit, LE and BE).
The changes were tested with QEMU's 'mips' target.
Most of the implementation was lifted from the ARM version, the appropriate
MIPS-specific things were implemented.
With these changes I am able to go all the way through the u-boot->ubldr->kernel
boot chain in QEMU on all combinations of bit-ness and endian-ness.
For the tests I've used FAT32 disk images (as FAT32 is supported by U-boot),
which include /boot/kernel/kernel and /boot/kernel/ubldr.bin
In U-boot I do:
fatload ide 0 <LOAD_ADDR> /boot/kernel/ubldr.bin; go <LOAD_ADDR>
where LOAD_ADDR is 80800000 for 32-bit and ffffffff80800000 for 64-bit
Then it's the usual ubldr that takes over and loads and starts a kernel.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5313
ubldr.
The changes are mostly dealing with removing unnecessary casts from the U-Boot
API (we're passing only pointers, no obvious reason to cast them to uint32_t),
cleaning up some compiler warnings and using the proper printf format
specifiers in order to be able to compile cleanly for both 32-bit and 64-bit
MIPS targets.
Reviewed by: imp
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5312
translate directly into calls to their namesake API functions in
libvmmapi.
It is an improvement over the existing setreg(), setmsr(), setcr()
setgdt() and exec() callbacks in that the new additions give full
control and don't assume we're booting FreeBSD, like exec() and
don't assume one only wants to set the value of RSP, like setreg().
sys/boot/fdt/Makefile
sys/boot/uboot/fdt/Makefile
sys/boot/uboot/lib/Makefile
This causes compilation issues on MIPS due to trying to link PIC with non-PIC
code. This revision includes bsd.stand.mk in the above files.
Reviewed by: imp
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5311
Although this may not be an issue in practice, it would be more correct if the 64-bit version was used. Also, using the 64-bit version would make it easier to add support for 64-bit ubldr on MIPS.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5310
The HDMI driver will attach a framebuffer device when a display is
connected. If the EDID can be read and contains a preferred mode, it
will be used. Otherwise the framebuffer will default to 800x600.
In addition, if the EDID contains a CEA-861 extension block and the
"basic audio" flag is set, audio playback at 48kHz 16-bit stereo is
enabled on the controller.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5383
These are no longer needed after the recent 'beforebuild: depend' changes
and hooking DIRDEPS_BUILD into a subset of FAST_DEPEND which supports
skipping 'make depend'.
Sponsored by: EMC / Isilon Storage Division
Tested on Spike simulator with 2 and 16 cores (tlb enabled),
so set MAXCPU to 16 at this time.
This uses FDT data to get information about CPUs
(code based on arm64 mp_machdep).
Invalidate entire TLB cache as it is the only way yet.
Sponsored by: DARPA, AFRL
Sponsored by: HEIF5
import it into the loader(8) env as dhcp.root-path, so that it overrides
any dhcp/bootp server-provided path.
Now if you have a dhcp server available you can easily net-boot a u-boot
system even if you don't control the dhcp server config, by setting just
two variables in the u-boot env:
loaderdev=net
rootpath=<nfsserverip>:<pathname>
Previously you had to either accept all the dhcp parameters from the
server without the ability to locally provide the rootpath, or you had
to forego dhcp and set more vars (ipaddr, netmask, serverip, rootpath).
configuration from the FDT data, then set the pins into the requested
state. As part of this the gpio controller now reports the correct number
of pins instead of returning the number of bank * 32.
To allow for a future consolidated kernel we add the SOC_ALLWINNER_A10 and
SOC_ALLWINNER_A20 kernel options. These need to be set as appropriate for
the SoC the kernel will boot on.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5177
A10/A20 SoC. Based loosely on the submitters NetBSD driver, tested on
Cubieboard 2. Playback and capture are supported.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5202