Get counting volume I/Os right.
launch_requests: Be macho, throw away the safety net and walk the
tightrope with no splbio().
Add some comments explaining the smoke and mirrors.
Remove some redundant braces.
sdio: Set the state of an accessed but down subdisk correctly. This
appears to duplicate an earlier commit that I hadn't seen.
Get counting volume I/Os right.
Count buffer sizes correctly for architectures where ints are not 32 bits.
complete_rqe: Move decrementing active count until after call to
complete_raid5_write, thus possibly avoiding a race condition.
Suggested-by: dillon
Rename user bp to ubp to avoid confusion.
Tidy up comments.
PRs!" So here I go.
Add definitions for some of the AMD CPU feature bits. Also add a comment on
where to find the rest of them. This is a purely cosmetic change.
PR: i386/14438
Submitted by: Kelly Yancey <kbyanc@egroups.net>
is used to control whether the debug messages are output at runtime.
It defaults to on so that if you define BUS_DEBUG in your kernel
then you get all the debugging info when you boot.
It's very useful for disabling all the debugging info when you're
developing a loadable device driver and you're doing lots of loads
and unloads but don't always want to see all the debugging info.
a struct buf. Don't try to examine B_ASYNC, it is a layering violation
to do so. The only current user of this interface is vn(4) which, since
it emulates a disk interface, operates on struct bio already.
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
provide locking over extended attribute operations, requiring that
individual operations be atomic. Allowing non-zero starting offsets
permits applications/etc to put themselves at risk for inconsistent
behavior. As VOP_SETEXTATTR already prohibited non-zero write offsets,
this makes sense.
Suggested by: Andreas Gruenbacher <a.gruenbacher@bestbits.at>
calling in_pcbbind so that in_pcbbind sees a valid address if no
address was specified (since divert sockets ignore them).
PR: 17552
Reviewed by: Brian
from the sys Makefile's SUBDIRs. This is conditioned in make.conf by the
NO_MODULES variable and the existence of the modules directory. The
actual location of the modules is not modified. Changes in Makefiles
only, this does not affect Peter's recent changes.
Reviewed by: Peter Wemm, who warned me I would get some flack, and
he had the good idea for the NO_MODULES variable.
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
via the MODULE_VERSION() and MODULE_DEPEND() macros that both the loader
and kld system know how to deal with. The old DT_NEEDED tag is still
supported by the loader (and will remain supported for a while) - but the
kernel side presently doesn't know how to deal with DT_NEEDED.
Remove evil allocation macros from machdep.c (why was that there???) and
use malloc() instead.
Move paramters out of param.h and into the code itself.
Move a bunch of internal definitions from public sys/*.h headers (without
#ifdef _KERNEL even) into the code itself.
I had hoped to make some of this more dynamic, but the cost of doing
wakeups on all sleeping processes on old arrays was too frightening.
The other possibility is to initialize on the first use, and allow
dynamic sysctl changes to parameters right until that point. That would
allow /etc/rc.sysctl to change SEM* and MSG* defaults as we presently
do with SHM*, but without the nightmare of changing a running system.
