This both avoids some dependencies on xinstall.host and allows
bootstrapping on older releases to work due to lack of at least 'install -l'
support.
Sponsored by: EMC / Isilon Storage Division
descriptor to avoid trashing valid file descriptors that access dev->fd at a
later point in time
PR: 192671
Submitted by: Scott Ferris <scott.ferris@isilon.com>
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
Since METAMODE has been added, sys.mk loads bsd.mkopt.mk which ends load loading
bsd.own.mk which then defines SHLIBDIR before all the Makefile.inc everywhere.
This makes /lib being populated again.
Reported by: many
Off by default, build behaves normally.
WITH_META_MODE we get auto objdir creation, the ability to
start build from anywhere in the tree.
Still need to add real targets under targets/ to build packages.
Differential Revision: D2796
Reviewed by: brooks imp
The reasoning behind this, is that if we are consistent in our
documentation about the uint*_t stuff, people will be less tempted to
write new code that uses the non-standard types.
I am not going to bump the man page dates, as these changes can be
considered style nits. The meaning of the man pages is unaffected.
MFC after: 1 month
The index() and rindex() functions were marked LEGACY in the 2001
revision of POSIX and were subsequently removed from the 2008 revision.
The strchr() and strrchr() functions are part of the C standard.
This makes the source code a lot more consistent, as most of these C
files also call into other str*() routines. In fact, about a dozen
already perform strchr() calls.
This includes support in the kernel, camcontrol(8), libcam and the mps(4)
driver for SMP passthrough.
The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00
to determine supported pages, and will now fetch page 0x83 in addition to
page 0x80 if supported.
Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is
intended for SMP requests and responses. The ADVINFO is currently used to
fetch cached VPD page 0x83 data from the transport layer, but is intended
to be extensible to fetch other types of device-specific data.
SMP-only devices are not currently represented in the CAM topology, and so
the current semantics are that the SIM will route SMP CCBs to either the
addressed device, if it contains an SMP target, or its parent, if it
contains an SMP target. (This is noted in cam_ccb.h, since it will change
later once we have the ability to have SMP-only devices in CAM's topology.)
smp_all.c,
smp_all.h: New helper routines for SMP. This includes
SMP request building routines, response parsing
routines, error decoding routines, and structure
definitions for a number of SMP commands.
libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality
is available to userland applications.
camcontrol.8,
camcontrol.c: Add smp passthrough support to camcontrol. Several
new subcommands are now available:
'smpcmd' functions much like 'cmd', except that it
allows the user to send generic SMP commands.
'smprg' sends the SMP report general command, and
displays the decoded output. It will automatically
fetch extended output if it is available.
'smppc' sends the SMP phy control command, with any
number of potential options. Among other things,
this allows the user to reset a phy on a SAS
expander, or disable a phy on an expander.
'smpmaninfo' sends the SMP report manufacturer
information and displays the decoded output.
'smpphylist' displays a list of phys on an
expander, and the CAM devices attached to those
phys, if any.
cam.h,
cam.c: Add a status value for SMP errors
(CAM_SMP_STATUS_ERROR).
Add a missing description for CAM_SCSI_IT_NEXUS_LOST.
Add support for SMP commands to cam_error_string().
cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP
commands are by nature bi-directional, and we may
need to support bi-directional SCSI commands later.
Add the XPT_SMP_IO CCB. Since SMP commands are
bi-directional, there are pointers for both the
request and response.
Add a fill routine for SMP CCBs.
Add the XPT_GDEV_ADVINFO CCB. This is currently
used to fetch cached page 0x83 data from the
transport later, but is extensible to fetch many
other types of data.
cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO
and XPT_GDEV_ADVINFO CCBs.
cam_xpt.c: Add support for executing XPT_SMP_IO CCBs.
cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct
cam_ed.
scsi_all.c: Add scsi_get_sas_addr(), a function that parses
VPD page 0x83 data and pulls out a SAS address.
scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a
prototype for scsi_get_sas_addr().
scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and
XPT_GDEV_ADVINFO CCBs.
scsi_xpt.c: In the SCSI probe code, first ask the device for
VPD page 0x00. If any VPD pages are supported,
that page is required to be implemented. Based on
the response, we may probe for the serial number
(page 0x80) or device id (page 0x83).
Add support for the XPT_GDEV_ADVINFO CCB.
sys/conf/files: Add smp_all.c.
mps.c: Add support for passing in a uio in mps_map_command(),
so we can map a S/G list at once.
Add support for SMP passthrough commands in
mps_data_cb(). SMP is a special case, because the
first buffer in the S/G list is outbound and the
second buffer is inbound.
Add support for warning the user if the busdma code
comes back with more buffers than will work for the
command. This will, for example, help the user
determine why an SMP command failed if busdma comes
back with three buffers.
mps_pci.c: Add sys/uio.h.
mps_sas.c: Add the SAS address and the parent handle to the
list of fields we pull from device page 0 and cache
in struct mpssas_target. These are needed for SMP
passthrough.
Add support for the XPT_SMP_IO CCB. For now, this
CCB is routed to the addressed device if it supports
SMP, or to its parent if it does not and the parent
does. This is necessary because CAM does not
currently support SMP-only nodes in the topology.
Make SMP passthrough support conditional on
__FreeBSD_version >= 900026. This will make it
easier to MFC this change to the driver without
MFCing the CAM changes as well.
mps_user.c: Un-staticize mpi_init_sge() so we can use it for
the SMP passthrough code.
mpsvar.h: Add a uio and iovecs into struct mps_command for
SMP passthrough commands.
Add a cm_max_segs field to struct mps_command so
that we can warn the user if busdma comes back with
too many segments.
Clear the cm_reply when a command gets freed. If
it is not cleared, reply frames will eventually get
freed into the pool multiple times and corrupt the
pool. (This fix is from scottl.)
Add a prototype for mpi_init_sge().
sys/param.h: Bump __FreeBSD_version to 900026 for the for the
inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO
CAM CCBs.
Remove or re-work support for the several features from the past:
- remove incomplete support for trimming slice/partition names
- remove mapping from old device names "sd" and "st"
- remove whitespace trimming
- remove unconditional skipping of leading 'r' in a device name
- skip leading 'n' or 'e' only if the following device name matches
a list of known devices that support no-rewind and eject-on-close
features; currently this is only sa(4)
- reflect the above changes in comments in code and in cam(3)
- remove a note cautioning against use of cam_get_device and
cam_open_device in cam(3)
Reviewed by: mjacob
Although groff_mdoc(7) gives another impression, this is the ordering
most widely used and also required by mdocml/mandoc.
Reviewed by: ru
Approved by: philip, ed (mentors)
Similar to libexec/, do the same with lib/. Make WARNS=6 the norm and
lower it when needed.
I'm setting WARNS?=0 for secure/. It seems secure/ includes the
Makefile.inc provided by lib/. I'm not going to touch that directory.
Most of the code there is contributed anyway.
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
according to my reading of the CAM draft is mandatory for
all CCB function calls and enforced by xptioctl() since at
least r168752. Previously we happened to use 0 as the Path
ID, causing the XPT_DEV_MATCH call to fail if there's no
SCSI bus 0. Basically the same bug was also fixed the same
way for camcontrol(8) as part of r126514.
PR: 127605
Submitted by: Eygene Ryabinkin
Approved by: silence from ken and scottl
MFC after: 1 week
- It is acceptable to call free(3) when the given pointer itself
is NULL, so we do not need to determine NULL before passing
a pointer to free(3)
- Handle failure of malloc(3)
MT6/5 Candidate
Submitted by: Dan Lukes <dan at obluda cz>
PR: bin/83352
binaries in /bin and /sbin installed in /lib. Only the versioned files
reside in /lib, the .so symlink continues to live /usr/lib so the
toolchain doesn't need to be modified.
and libdevstat, since the new way of doing things is to just list
maintainership in src/MAINTAINERS.
Also, remove duplicate entries in src/MAINTAINERS for those utilities. I
already had entries for them.
- fix a potential overrun made worse by rev 1.5 of camlib.h
- change strncpy() and strcpy() calls to strlcpy()
- use sizeof(string[]) instead of STRING_LEN to avoid future problems
- get rid of an unused variable
Thanks to BDE for pointing out some of the problems.
MFC after: 2 weeks
