beacon or probe-response frames. Fix the condition by checking for the
the array's content instead of the always existing array itself.
Reviewed by: rpaulo, stefanf
MFC after: 3 days
its internal data. This has been used to bypass missing calls in drivers
which do not use the ratectl framework correctly. Issue is, not all algos
use that variable, or even have internal data, therefore valid calls are
not done. Fix this by removing the checks, all driver issues should be
resolved.
MFC after: 1 week
the currently selected rate. The calculations of course need a valid
rate. To make that possible before any call to node_rate() is done,
initialize ni_txrate on none_node_init() calls.
MFC after: 1 week
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
This can happen if the algos are built as modules but are not loaded. If
the selected ratectl algo is not available, try to load it (The load
module functions does nothing currently). Add a dummy ratectl algo which
always selects the first available rate. Use that one if the desired algo
is not available.
MFC after: 1 week
802.11 duplicate detection. Upon looking at the standard, we discover
that 802.11-2007 says:
"A receiving QoS STA is also required to keep only the most recent
cache entry per<Address 2, TID, sequence-number> triple, storing only
the most recently received fragment number for that triple. A receiving
STA may omit tuples obtained from broadcast/multicast or ATIM frames
from the cache."
To fix this, we just disable duplicate detection for multicast/broadcast
frames.
Reviewed by: sam
MFC after: 4 weeks
Obtained from: DragonFly
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
ratectl_node_init() functions and since ni_rtctls was already
malloc'ed() we will panic. Fix this by using the already malloc'ed
pointer.
Found by: bschmidt
Reviewed by: bschmidt
* WPA-None requires ap_scan=2:
The major difference between ap_scan=1 (default) and 2 is, that no
IEEE80211_IOC_SCAN* ioctls/functions are called, though, there is a
dependency on those. For example the call to wpa_driver_bsd_scan()
sets the interface UP, this never happens, therefore the interface
must be marked up in wpa_driver_bsd_associate(). IEEE80211_IOC_SSID
also is not called, which means that the SSID has not been set prior
to the IEEE80211_MLME_ASSOC call.
* WPA-None has no support for sequence number updates, it doesn't make
sense to check for replay violations..
* I had some crashes right after the switch to RUN state, issue is
that sc->sc_lastrs was not yet defined.
Approved by: rpaulo (mentor)
MFC after: 3 weeks
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
iv_recv_mgmt(). iv_recv_mgmt() will generate management frame responses
and pass them to bpf before the management frame that triggered the
response.
PR: 144323
Submitted by: Alexander Egorenkov <egorenar at gmail.com>
MFC after: 2 weeks
Sponsored by: iXsystems, inc.
o Process the BAR frame on the adhoc, mesh and sta modes
o Fix the format of the ADDBA reply frame
o Fix references to the spec section numbers
Also, print the all the MCS rates in bootverbose.
Sponsored by: iXsystems, Inc.
Obtained from: //depot/user/rpaulo/80211n/...
ifmultiaddr structures' reference to the parent interface, unless the parent
interface is really detaching. While here, program only link layer multicast
filters to a wlan's hardware parent interface.
PR: kern/142391, kern/142392
Reviewed by: sam, rpaolo, bms
MFC after: 1 week
the parent wirless interface. If the user passed in a mac address or it was
autogenerated then flag this to avoid trashing it on update.
This will fix wlan+lagg in a post vap world.
