reasonable defaults.
This avoids confusing and ugly casting to eopnotsupp or making dummy functions.
Bogus casting of filesystem sysctls to eopnotsupp() have been removed.
This should make *_vfsops.c more readable and reduce bloat.
Reviewed by: msmith, eivind
Approved by: phk
Tested by: Jeroen Ruigrok/Asmodai <asmodai@wxs.nl>
return (in signal trampoline code). I plan to do the same on -stable,
so that we have a consistent interface to userland applications.
Reviewed by: bde
2) s/MODLOAD/KMODLOAD/ to be consistent with the rest of the variables
(KMOD, KMODOWN, KMODGRP, etc) and definition of MODLOAD/UNLOAD in the
Makefile of the ATAPI module
3) textual fixups
rewrite the pccard attachment case. This is a work in progress, but
doesn't break the isa case.
I left the #if 0...#endif around the pccard stuff, at Peter's request,
so that normal users don't shoot themselves in the foot.
While I was here:
o Indent a comment to the right location
o Spell Unknown with a final 'n'.
Reviewed by: peter
will allow newbus based drivers to have pccard attachments. Also
start printing out probe messages for pccards stating the resources
used and regularize many of the pccard printfs.
Reviewed by: Peter Wemm.
I have an 82559 card with the same id as the other 8255[78] chips, but
that was made with a date code of 0699 (June 99). The submitter shows
this working with the probe etc, but doesn't actually say it works as
on the ethernet. :-) Assuming it does, this is a RELENG_3 merge candidate.
Submitted by: Steven E Lumos <slumos@sam.ISRI.UNLV.EDU>
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
this PHY and the Davicom DM9101 have exactly the same register definitions.
One of them is probably a clone of the other. I'm not sure which.
This is needed for the Davicom DM9102 10/100 PCI ethernet driver which
will be committed shortly.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
the other XXXFS_DIAGNOSTIC options (not very) and mostly controlled
tracing of normal operation. Use `#ifdef DEBUG' for non-diagnostics
and `#ifdef DIAGNOSTIC' for diagnostics.
- Make as much of the makefile for each of the three flavours
(disk, CDROM, net) common.
- Special-case the libalpha startup module on its use in boot1, not
the other way around.
- Build the loader out of a "loader" directory
Reviewed by: mjacob, dfr
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
MCA SCSI adapters.
bt_mca.c is going to live in sys/dev/buslogic instead of sys/dev/mca
as per a conversation with Peter, Doug and Mike.
Thanks to Andy Farkas <andyf@speednet.com.au> for being such a good
sport and doing all the testing for me (as I don't actually own one
of these cards. Yet.)
the actual work. When USER_LDT is not defined for a kernel, sysarch returns
EOPNOTSUPP. Display a message in that case and return ENOSYS to userland.
Reviewed by: luoqi
1. Move definitions of struct i386_*_args to the header file sysarch.h,
since they are part of the sysarch API. struct i386_get_ldt_args and
i386_set_ldt_args were identical, therefore make them into one
struct i386_ldt_args. Libc should use these definitions as well.
2. Return a more sensible EOPNOTSUPP for unknown operations.
Reviewed by: marcel
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
Fix a bug where video capture locks up on channel changes.
Many thanks to Juha for solving this.
Submitted by: Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
Remove WD formatting code which has never worked in 386bsd or FreeBSD.
Remove DIOCSSTEP and DIOCSRETRIES ioctls as well, they belong in
history, along with the SMD disks.
OK'ed by: bde
* Make it possible to type a filename to boot1 so that it is possible to
recover from fatally broken versions of /boot/loader.
* Make a start at a CD boot program (not yet functional).
external NatSemi PHY chip was programmed to respond to MII address 24.
In the 3c905B ASICs, the transceiver is internal but it's still mapped
to MII address 24. But *some* 3Com 3c905B ASIC revisions map the
transceiver control registers to *all* MII addresses (0 through 31).
The miibus code probes for PHYs at all MII addresses and because of
this unusual behavior, it will attempt to map the same PHY registers
several times over, which doesn't work.
Naturally, the 3c905B NIC that I tested happened not to exhibit this
behavior.
The fix is to tweak xl_miibus_readreg() and xl_miibus_writereg()
to only respond when attempting to read from MII address 24. This
is safe to do since the 3Com documentation indicates that the PHY
and/or internal transceiver will always be mapped to address 24,
and there are no 3Com XL NICs with more than one PHY.
New Features:
Greatly improved VBI capture support. (mainly for the AleVT port)
Supports select() on /dev/vbi
Improved RISC program for RGB+VBI capture to capture both evenodd
VBI data even when only capturing even only (or odd only) video
Based on code from Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
Support for Hauppauge 627 and Temic 4006
Submitted by: Maurice Castro <maurice@atum.castro.aus.net>
Bug Fix:
Fix bug in AverMedia card detection.
an operation, as a kernel client may not have previously checked the CPU
type (it may not be able to).
Also correct the function declaration style for the mem_range functions to
match the rest of this file (oops).
Submitted by: gibbs
- eliminate the fast/slow timeout lists for TCP and instead use a
callout entry for each timer.
- increase the TCP timer granularity to HZ
- implement "bad retransmit" recovery, as presented in
"On Estimating End-to-End Network Path Properties", by Allman and Paxson.
Submitted by: jlemon, wollmann
Break out the detection logic for the aic7855 and properly report
these chips as 7855s instead of 7850s.
The 2940AU_CN is an aic7860 based card, not aic7860.
Not setting CACHETHEN turned out to be a bad idea. It can cause
spurious corruption under heavy PCI load with multiple masters.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best before it kills Matt :-)
Use the specfs routines rather having cloned copies in devfs.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best.
Use the specfs routines rather having cloned copies in devfs.
statement to put the rcsid into the .comment section. This allows
the comments (ie:version id's of compiler, headers, source, etc) to be
stripped out with the standard tools (strip/objcopy). SVR4 has a
tool called 'mcs' (manipulate comment section) which allows you to
add/remove/compact strings. Removing duplicate strings helps a lot
if the headers generate them.
Using __attribute__((section(".comment"))) would probably also work,
but that still leaves the RCSID occupying C name space somewhere.
due to the fact that there are non-MII cards supported by the same
driver and I don't have all of the cards available for testing. There's
also the 3c905B-COMBO which has MII, AUI and BNC media ports all in one
package. Supporting the COMBO is difficult because we have to add the
10base5 and 10base2 media types to the same ifmedia struct as the
MII-attached types, however there is no way to force the miibus and
child PHYs into existence before xl_attach() completes, so there is
no ifmedia struct available in xl_attach(). What we do inistead is
use the mediainit method as a callback: when a child PHY is attached,
it calls the miibus mediainit routine which selects a default media.
This routing also calls the NIC driver's mediainit method (if it
implements one) at which point we can safely add the other media
types.
ones were made by Lucent). The Broadcom chip also appears to use an
internal PHY made by Broadcom which uses the Broadcom OUI. This is different
from previous ASICs which always returned 0 in the PHY ID registers.
To account for this, I added the necessary ID values for the Broadcom
PHY so that it can be detected and attached using the 3Com PHY driver
instead of defaulting to the generic one.
UMAPFS_DIAGNOSTIC and UNION_DIAGNOSTIC. Uncommented NULLFS_DIAGNOSTIC.
It is as bogus as the above three but since it is already a new-style
option it is easier to use it than to fix it.
format errors exposed by this. It has nothing to do with diagnostics
since it does little more than control tracing of normal operation.
Actual diagnostics for the union file system are still controlled by
the DIAGNOSTIC option.
or DDB and fixed printf format errors exposed by this. The options had
little to do with diagnostics; they mostly controlled tracing of normal
operation.
This fixes, at least, panics in ncr_attach() on i386's with about 5MB
of memory. The restriction was a hack to leave some low memory for ISA
DMA, but on i386's we now allocate pages from the top down, so all the
restriction did was cause our allocations to fail when there is no free
memory above 1MB.
some swapper problems analogous to those experienced with ccd.
This fix is a kludge: since we currently don't track the "sector size"
in a volume label, we guess a worst case (4 kB, as used by vnode
devices). If the concept of sector size is here to stay, I'll make
some changes to track the "sector size" of a volume. This will
probably be the maximum of the sector sizes of all component drives,
but things could get ugly if we start allowing non-standard sector
sizes such as 524 bytes.
Unkludged-version-submitted-by: phk
discussed on current.
The following variables are defined (for now):
osname (defaults to "Linux")
Allow users to change the name of the OS as returned by uname(2),
specially added for all those Linux Netscape users and statistics
maniacs :-) We now have what we all wanted!
osrelease (defaults to "2.2.5")
Allow users to change the version of the OS as returned by uname(2).
Since -current supports glibc2.1 now, change the default to 2.2.5
(was 2.0.36).
oss_version (defaults to 198144 [0x030600])
This one will be used by the OSS_GETVERSION ioctl (PR 12917) which I
can commit now that we have the MIB. The default version number is the
lowest version possible with the current 'encoding'.
A note about imprisoned processes (see jail(2)):
These variables are copy-on-write (as suggested by phk). This means that
imprisoned processes will use the system wide value unless it is written/set
by the process. From that moment on, a copy local to the prison will be
used.
A note about the implementation:
I choose to add a single pointer to struct prison, because I didn't like the
idea of changing struct prison every time I come up with a new variable. As
a side effect, the extra storage is only needed when a variable is set from
within the prison. This also minimizes kernel bloat when the Linuxulator is
not used; both compiled in or as a module.
Reviewed by: bde (first version only) and phk
had to get the ML 6692 PHY driver working correctly, which is harder than
it sounds. "Bitrate" ThunderLAN devices should still be supported (i.e
the older 10Mbps Netflex 3/P, which use the TNETE110 chip that has no
MII support). The ThunderLAN has an internal PHY which makes things a
little complicated, but these are the basic rules:
- For devices with just the ThunderLAN, the internal PHY is used to
provide 10baseT, and 10base5/10baseT support. Autonegotiation will
work, but only with 10baseT links. The only thing that really gets
negotiated is whether the link is full or half duplex.
- For devices with the ThunderLAN and an external 10/100 PHY (like the
Compaq Netelligent 100Mbps cards, or the internal Netflex 3/P with
100Mbps upgrade daughter card), the external PHY is used for 10baseT
and 100baseTX modes. The internal PHY is still used to support
10base5/10base2, though you have to select them manual with ifconfig.
- For devices with the ThunderLAN and the ML6692 PHY, both the internal
and external PHYs are used, though it will appear as though the 6692
PHY will be used to support 10baseT and 100baseTX modes. In reality,
the internal PHY will be used for 10baseT, but this fact will be hidden
from the user. The 10base5/10base2 modes can also be selected manually
as with above.
ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is
a port of the NetBSD driver with various hacks. The ML driver is necessary
to support the Olicom OC-2326 ThunderLAN-based NIC.
Also regenerated miidevs.h to pick up the proper 'obtained from'
revision string.
in the child. This corrects a problem where linux/alpha binaries see
the child's return value of fork as the parent's pid. This happens because
linux/alpha binaries apparently check the return value directly, rather
than looking for a non-zero value in a4, as *BSD & OSF/1 do.
Reviewed by:dfr@nlsystems.com
