the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
if attach succeeded. device_is_alive just tells us that probe
succeeded. Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.
Symptoms of problem reported by: martin blapp
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
- Remove locking of the softc in the attach method, instead depending on
bus_setup_intr being at the end of attach (delaying interrupt enable until
after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
in detach to only free resources that were allocated. This puts all
resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before. It was unnecessary
to move it. This reverts part of 1.88
- rl: move irq allocation before ether_ifattach. Problems might have been
caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
null pointer.
Reviewed by: imp, mdodd
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
prevent/workaround TX lockups in this driver. The secret seems to be to
not let the TX DMA queue become too full. If we have too many packets
in the queue, we should wait for them to drain a bit before trying to
queue more. This should prevent the lockup from occurring, and if it
does occur, there is special code in sf_start() to kick the NIC in the
head and get it going again.
Special thanks to Glen Neff for helping me test this fix.
night of testing before merging to -stable.
Also added to code to detect TX underruns and automatically increase the
TX threshold to avoid them. Carefully placed diagnostig printf() about
this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from
confused users, like I always do with the xl and dc drivers.
something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
before selecting a mode. The Seeq PHY chips on the Adaptec cards that
use the AIC-6915 controller seem to need it in order to get them to
change modes correctly.
This corrects a problem that I noticed where my ANA-62022 board failed
to correctly program the full duplex bit in the macconfig1 register
when the interface was brought up. Running ifconfig sf0 would mask this
problem in some cases because polling the PHY status would cause the
miibus code to notice that full duplex was now needed and the statchg
callback would be invoked to configure the duplex setting. However it
would still get it wrong other times.
Also changed sf_miibus_statchg() to program the IPG register to match
the duplex setting in accordance with Adaptec manual's recommendations
(0x15 for full duplex, 0x11 for half duplex).
is documented to be 0x18 in the Adaptec manual, however there appears to
be a newer board rev with code 0x19. I added a #define for this and
updated the probe code so that this board will be properly identified
in the probe messages. (Currently it's just identified generically as
an AIC-6915 chip.)
