The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before this can be
flipped on for those chips (mostly to do with setting up the different
bias values and LNA1/LNA2 RSSI differences) but the first stage is
putting this code into the driver layer so it can be reused.
This has the added benefit of making it easier to expose configuration
options and diagnostic information via the ioctl API. That's not yet
being done but it sure would be nice to do so.
Tested:
* AR9285, with LNA diversity enabled
* AR9285, with LNA diversity disabled in EEPROM
for the WB195 combo NIC - an AR9285 w/ an AR3011 USB bluetooth NIC.
The AR3011 is wired up using a 3-wire coexistence scheme to the AR9285.
The code in if_ath_btcoex.c sets up the initial hardware mapping
and coexistence configuration. There's nothing special about it -
it's static; it doesn't try to configure bluetooth / MAC traffic priorities
or try to figure out what's actually going on. It's enough to stop basic
bluetooth traffic from causing traffic stalls and diassociation from
the wireless network.
To use this code, you must have the above NIC. No, it won't work
for the AR9287+AR3012, nor the AR9485, AR9462 or AR955x combo cards.
Then you set a kernel hint before boot or before kldload, where 'X'
is the unit number of your AR9285 NIC:
# kenv hint.ath.X.btcoex_profile=wb195
This will then appear in your boot messages:
[100482] athX: Enabling WB195 BTCOEX
This code is going to evolve pretty quickly (well, depending upon my
spare time) so don't assume the btcoex API is going to stay stable.
In order to use the bluetooth side, you must also load in firmware using
ath3kfw and the binary firmware file (ath3k-1.fw in my case.)
Tested:
* AR9280, no interference
* WB195 - AR9285 + AR3011 combo; STA mode; basic bluetooth inquiries
were enough to cause traffic stalls and disassociations. This has
stopped with the btcoex profile code.
TODO:
* Importantly - the AR9285 needs ASPM disabled if bluetooth coexistence
is enabled. No, I don't know why. It's likely some kind of bug to do
with the AR3011 sending bluetooth coexistence signals whilst the device
is asleep. Since we don't actually sleep the MAC just yet, it shouldn't
be a problem. That said, to be totally correct:
+ ASPM should be disabled - upon attach and wakeup
+ The PCIe powersave HAL code should never be called
Look at what the ath9k driver does for inspiration.
* Add WB197 (AR9287+AR3012) support
* Add support for the AR9485, which is another combo like the AR9285
* The later NICs have a different signaling mechanism between the MAC
and the bluetooth device; I haven't even begun to experiment with
making that HAL code work. But it should be a lot more automatic.
* The hardware can do much more interesting traffic weighting with
bluetooth and wifi traffic. None of this is currently used.
Ideally someone would code up something to watch the bluetooth traffic
GPIO (via an interrupt) and then watch it go high/low; then figure out
what the bluetooth traffic is and adjust things appropriately.
* If I get the time I may add in some code to at least track this stuff
and expose statistics. But it's up to someone else to experiment with
the bluetooth coexistence support and add the interesting stuff (like
"real" detection of bulk, audio, etc bluetooth traffic patterns and
change wifi parameters appropriately - eg, maximum aggregate length,
transmit power, using quiet time to control TX duty cycle, etc.)
the RX antenna field.
The AR9285/AR9485 use an LNA mixer to determine how to combine the signals
from the two antennas. This is encoded in the RSSI fields (ctl/ext) for
chain 2. So, let's use that here.
This maps RX antennas 0->3 to the RX mixer configuration used to
receive a frame. There's more that can be done but this is good enough
to diagnose if the hardware is doing "odd" things like trying to
receive frames on LNA2 (ie, antenna 2 or "alt" antenna) when there's
only one antenna connected.
Tested:
* AR9285, STA mode
* Grab the reset lock first, so any subsequent interrupt, TX, RX work
will fail
* Then shut down interrupts
* Then wait for TX/RX to finish running
At this point no further work will be running, so it's safe to do the
reset path code.
PR: kern/179232
and if queue mechanism; also fix up (non-11n) TX fragment handling.
This may result in a bit of a performance drop for now but I plan on
debugging and resolving this at a later stage.
Whilst here, fix the transmit path so fragment transmission works.
The TX fragmentation handling is a bit more special. In order to
correctly transmit TX fragments, there's a bunch of corner cases that
need to be handled:
* They must be transmitted back to back, in the same order..
* .. ie, you need to hold the TX lock whilst transmitting this
set of fragments rather than interleaving it with other MSDUs
destined to other nodes;
* The length of the next fragment is required when transmitting, in
order to correctly set the NAV field in the current frame to the
length of the next frame; which requires ..
* .. that we know the transmit duration of the next frame, which ..
* .. requires us to set the rate of all fragments to the same length,
or make the decision up-front, etc.
To facilitate this, I've added a new ath_buf field to describe the
length of the next fragment. This avoids having to keep the mbuf
chain together. This used to work before my 11n TX path work because
the ath_tx_start() routine would be handed a single mbuf with m_nextpkt
pointing to the next frame, and that would be maintained all the way
up to when the duration calculation was done. This doesn't hold
true any longer - the actual queuing may occur at any point in the
future (think ath_node TID software queuing) so this information
needs to be maintained.
Right now this does work for non-11n frames but it doesn't at all
enforce the same rate control decision for all frames in the fragment.
I plan on fixing this in a followup commit.
RTS/CTS has the same issue, I'll look at fixing this in a subsequent
commit.
Finaly, 11n fragment support requires the driver to have fully
decided what the rate scenario setup is - including 20/40MHz,
short/long GI, STBC, LDPC, number of streams, etc. Right now that
decision is (currently) made _after_ the NAV field value is updated.
I'll fix all of this in subsequent commits.
Tested:
* AR5416, STA, transmitting 11abg fragments
* AR5416, STA, 11n fragments work but the NAV field is incorrect for
the reasons above.
TODO:
* It would be nice to be able to queue mbufs per-node and per-TID so
we can only queue ath_buf entries when it's time to assemble frames
to send to the hardware.
But honestly, we should just do that level of software queue management
in net80211 rather than ath(4), so I'm going to leave this alone for now.
* More thorough AP, mesh and adhoc testing.
* Ensure that net80211 doesn't hand us fragmented frames when A-MPDU has
been negotiated, as we can't do software retransmission of fragments.
* .. set CLRDMASK when transmitting fragments, just to ensure.
traffic.
When transmitting non-aggregate traffic, we need to keep the hardware
busy whilst transmitting or small bursts in txdone/tx latency will
kill us.
This restores non-aggregate iperf performance, especially when doing
TDMA.
Tested:
* AR5416<->AR5416, TDMA
* AR5416 STA <-> AR9280 AP
of course.)
There's a few things that needed to happen:
* In case someone decides to set the beacon transmission rate to be
at an MCS rate, use the MCS-aware version of the duration calculation
to figure out how long the received beacon frame was.
* If TxOP enforcing is available on the hardware and we're doing TDMA,
enable it after a reset and set the TDMA guard interval to zero.
This seems to behave fine.
TODO:
* Although I haven't yet seen packet loss, the PHY errors that would be
triggered (specifically Transmit-Override-Receive) aren't enabled
by the 11n HAL. I'll have to do some work to enable these PHY errors
for debugging.
What broke:
* My recent changes to the TX queue handling has resulted in the driver
not keeping the hardware queue properly filled when doing non-aggregate
traffic. I have a patch to commit soon which fixes this situation
(albeit by reminding me about how my ath driver locking isn't working
out, sigh.)
So if you want to test this without updating to the next set of patches
that I commit, just bump the sysctl dev.ath.X.hwq_limit from 2 to 32.
Tested:
* AR5416 <-> AR5416, with ampdu disabled, HT40, 5GHz, MCS12+Short-GI.
I saw 30mbit/sec in both directions using a bidirectional UDP test.
The list-based DMA engine has the following behaviour:
* When the DMA engine is in the init state, you can write the first
descriptor address to the QCU TxDP register and it will work.
* Then when it hits the end of the list (ie, it either hits a NULL
link pointer, OR it hits a descriptor with VEOL set) the QCU
stops, and the TxDP points to the last descriptor that was transmitted.
* Then when you want to transmit a new frame, you can then either:
+ write the head of the new list into TxDP, or
+ you write the head of the new list into the link pointer of the
last completed descriptor (ie, where TxDP points), then kick
TxE to restart transmission on that QCU>
* The hardware then will re-read the descriptor to pick up the link
pointer and then jump to that.
Now, the quirks:
* If you write a TxDP when there's been no previous TxDP (ie, it's 0),
it works.
* If you write a TxDP in any other instance, the TxDP write may actually
fail. Thus, when you start transmission, it will re-read the last
transmitted descriptor to get the link pointer, NOT just start a new
transmission.
So the correct thing to do here is:
* ALWAYS use the holding descriptor (ie, the last transmitted descriptor
that we've kept safe) and use the link pointer in _THAT_ to transmit
the next frame.
* NEVER write to the TxDP after you've done the initial write.
* .. also, don't do this whilst you're also resetting the NIC.
With this in mind, the following patch does basically the above.
* Since this encapsulates Sam's issues with the QCU behaviour w/ TDMA,
kill the TDMA special case and replace it with the above.
* Add a new TXQ flag - PUTRUNNING - which indicates that we've started
DMA.
* Clear that flag when DMA has been shutdown.
* Ensure that we're not restarting DMA with PUTRUNNING enabled.
* Fix the link pointer logic during TXQ drain - we should always ensure
the link pointer does point to something if there's a list of frames.
Having it be NULL as an indication that DMA has finished or during
a reset causes trouble.
Now, given all of this, i want to nuke axq_link from orbit. There's now HAL
methods to get and set the link pointer of a descriptor, so what we
should do instead is to update the right link pointer.
* If there's a holding descriptor and an empty TXQ list, set the
link pointer of said holding descriptor to the new frame.
* If there's a non-empty TXQ list, set the link pointer of the
last descriptor in the list to the new frame.
* Nuke axq_link from orbit.
Note:
* The AR9380 doesn't need this. FIFO TX writes are atomic. As long as
we don't append to a list of frames that we've already passed to the
hardware, all of the above doesn't apply. The holding descriptor stuff
is still needed to ensure the hardware can re-read a completed
descriptor to move onto the next one, but we restart DMA by pushing in
a new FIFO entry into the TX QCU. That doesn't require any real
gymnastics.
Tested:
* AR5210, AR5211, AR5212, AR5416, AR9380 - STA mode.
PS-POLL support.
This implements PS-POLL awareness i nthe
* Implement frame "leaking", which allows for a software queue
to be scheduled even though it's asleep
* Track whether a frame has been leaked or not
* Leak out a single non-AMPDU frame when transmitting aggregates
* Queue BAR frames if the node is asleep
* Direct-dispatch the rest of control and management frames.
This allows for things like re-association to occur (which involves
sending probe req/resp as well as assoc request/response) when
the node is asleep and then tries reassociating.
* Limit how many frames can set in the software node queue whilst
the node is asleep. net80211 is already buffering frames for us
so this is mostly just paranoia.
* Add a PS-POLL method which leaks out a frame if there's something
in the software queue, else it calls net80211's ps-poll routine.
Since the ath PS-POLL routine marks the node as having a single frame
to leak, either a software queued frame would leak, OR the next queued
frame would leak. The next queued frame could be something from the
net80211 power save queue, OR it could be a NULL frame from net80211.
TODO:
* Don't transmit further BAR frames (eg via a timeout) if the node is
currently asleep. Otherwise we may end up exhausting management frames
due to the lots of queued BAR frames.
I may just undo this bit later on and direct-dispatch BAR frames
even if the node is asleep.
* It would be nice to burst out a single A-MPDU frame if both ends
support this. I may end adding a FreeBSD IE soon to negotiate
this power save behaviour.
* I should make STAs timeout of power save mode if they've been in power
save for more than a handful of seconds. This way cards that get
"stuck" in power save mode don't stay there for the "inactivity" timeout
in net80211.
* Move the queue depth check into the driver layer (ath_start / ath_transmit)
rather than doing it in the TX path.
* There could be some naughty corner cases with ps-poll leaking.
Specifically, if net80211 generates a NULL data frame whilst another
transmitter sends a normal data frame out net80211 output / transmit,
we need to ensure that the NULL data frame goes out first.
This is one of those things that should occur inside the VAP/ic TX lock.
Grr, more investigations to do..
Tested:
* STA: AR5416, AR9280
* AP: AR5416, AR9280, AR9160
* Move the node sleep/wake state under the TX lock rather than the
node lock. Let's leave the node lock protecting rate control only
for now.
* When reassociating, various state needs to be cleared. For example,
the aggregate session needs to be torn down, including any pending
aggregation negotiation and BAR TX waiting.
* .. and we need to do a "cleanup" pass since frames in the hardware
TX queue need to be transmitted.
Modify ath_tx_tid_cleanup() to be called with the TX lock held and push
frames into a completion list. This allows for the cleanup to be
done atomically for all TIDs in a node rather than grabbing and
releasing the TX lock each time.
a non-loss reset.
When the drain functions are called, the holding descriptor and link pointers
are NULLed out.
But when the processq function is called during a non-loss reset, this
doesn't occur. So the next time a DMA occurs, it's chained to a descriptor
that no longer exists and the hardware gets angry.
Tested:
* AR5416, STA mode; use sysctl dev.ath.X.forcebstuck=1 to force a non-loss
reset.
TODO:
* Further AR9380 testing just to check that the behaviour for the EDMA
chips is sane.
PR: kern/178477
of "right".)
Flip back on the "always continue TX DMA using the holding descriptor"
code - by always setting ATH_BUF_BUSY and never setting axq_link to NULL.
Since the holding descriptor is accessed via txq->axq_link and _that_
is done behind the TXQ lock rather than the TX path lock, the holding
descriptor stuff itself needs to be behind the TXQ lock.
So, do the mental gymnastics needed to do this.
I've not seen any of the hardware failures that I was seeing when
I last tried to do this.
Tested:
* AR5416, STA mode
I'm not sure why this is failing. The holding descriptor should be being
re-read when starting DMA of the next frame. Obviously something here
isn't totally correct.
I'll review the TX queue handling and see if I can figure out why this
is failing. I'll then re-revert this patch out and use the holding
descriptor again.
but partly to just tidy up things.
The problem here - there are too many TX buffers in the queue! By the
time one needs to transmit an EAPOL frame (for this PR, it's the response
to the group rekey notification from the AP) there are no ath_buf entries
free and the EAPOL frame doesn't go out.
Now, the problem!
* Enforcing the TX buffer limitation _before_ we dequeue the frame?
Bad idea. Because..
* .. it means I can't check whether the mbuf has M_EAPOL set.
The solution(s):
* De-queue the frame first
* Don't bother doing the TX buffer minimum free check until after
we know whether it's an EAPOL frame or not.
* If it's an EAPOL frame, allocate the buffer from the mgmt pool
rather than the default pool.
Whilst I'm here:
* Add a tweak to limit how many buffers a single node can acquire.
* Don't enforce that for EAPOL frames.
* .. set that to default to 1/4 of the available buffers, or 32,
whichever is more sane.
This doesn't fix issues due to a sleeping node or a very poor performing
node; but this doesn't make it worse.
Tested:
* AR5416 STA, TX'ing 100+ mbit UDP to an AP, but only 50mbit being received
(thus the TX queue fills up.)
* .. with CCMP / WPA2 encryption configured
* .. and the group rekey time set to 10 seconds, just to elicit the
behaviour very quickly.
PR: kern/138379
just "when the queue is busy."
After talking with the MAC team, it turns out that the linked list
implementation sometimes will not accept a TxDP update and will
instead re-read the link pointer. So even if the hardware has
finished transmitting a chain and has hit EOL/VEOL, it may still
re-read the link pointer to begin transmitting again.
So, always set ATH_BUF_BUSY on the last buffer in the chain (to
mark the last descriptor as the holding descriptor) and never
blank the axq_link pointer.
Tested:
* AR5416, STA mode
TODO:
* much more thorough testing with the pre-11n NICs, just to verify
that they behave the same way.
* test TDMA on the 11n and non-11n hardware.
* That lock isn't actually held during reset - just the whole TX/RX path
is paused. So, remove the assertion.
* Log the TX queue status - how many hardware frames are active in the
MAC and whether the queue is active.
is compiled in or not.
This fixes issues with people running -HEAD but who build modules
without doing a "make buildkernel KERNCONF=XXX", thus picking up
opt_*.h. The resulting module wouldn't have 11n enabled and the
chainmask configuration would just be plain wrong.
* Don't use BUS_DMA_ALLOCNOW for descriptor DMA maps; we never use
bounce buffers for the descriptors themselves.
* Add some XXX's to mark where the ath_buf has its mbuf ripped from
underneath it without actually cleaning up the dmamap. I haven't
audited those particular code paths to see if the DMA map is guaranteed
to be setup there; I'll do that later.
* Print out a warning if the descdma tidyup code is given some descriptors
w/ maps to free. Ideally the owner will free the mbufs and unmap
the descriptors before freeing the descriptor/ath_buf pairs, but
right now that's not guaranteed to be done.
Reviewed by: scottl (BUS_DMA_ALLOCNOW tag)
the buffer is being freed.
* When buffers are cloned, the original mapping isn't copied but it
wasn't freeing the mapping until later. To be safe, free the
mapping when the buffer is cloned.
* ath_freebuf() now no longer calls the busdma sync/unmap routines.
* ath_tx_freebuf() now calls sync/unmap.
* Call sync first, before calling unmap.
Tested:
* AR5416, STA mode
Each set of frames pushed into a FIFO is represented by a list of
ath_bufs - the first ath_buf in the FIFO list is marked with
ATH_BUF_FIFOPTR; the last ath_buf in the FIFO list is marked with
ATH_BUF_FIFOEND.
Multiple lists of frames are just glued together in the TAILQ as per
normal - except that at the end of a FIFO list, the descriptor link
pointer will be NULL and it'll be tagged with ATH_BUF_FIFOEND.
For non-EDMA chipsets this is a no-op - the ath_txq frame list (axq_q)
stays the same and is treated the same.
For EDMA chipsets the frames are pushed into axq_q and then when
the FIFO is to be (re) filled, frames will be moved onto the FIFO
queue and then pushed into the FIFO.
So:
* Add a new queue in each hardware TXQ (ath_txq) for staging FIFO frame
lists. It's a TAILQ (like the normal hardware frame queue) rather than
the ath9k list-of-lists to represent FIFO entries.
* Add new ath_buf flags - ATH_TX_FIFOPTR and ATH_TX_FIFOEND.
* When allocating ath_buf entries, clear out the flag value before
returning it or it'll end up having stale flags.
* When cloning ath_buf entries, only clone ATH_BUF_MGMT. Don't clone
the FIFO related flags.
* Extend ath_tx_draintxq() to first drain the FIFO staging queue, _then_
drain the normal hardware queue.
Tested:
* AR9280, hostap
* AR9280, STA
* AR9380/AR9580 - hostap
TODO:
* Test on other chipsets, just to be thorough.
related issues.
Moving the TX locking under one lock made things easier to progress on
but it had one important side-effect - it increased the latency when
handling CABQ setup when sending beacons.
This commit introduces a bunch of new changes and a few unrelated changs
that are just easier to lump in here.
The aim is to have the CABQ locking separate from other locking.
The CABQ transmit path in the beacon process thus doesn't have to grab
the general TX lock, reducing lock contention/latency and making it
more likely that we'll make the beacon TX timing.
The second half of this commit is the CABQ related setup changes needed
for sane looking EDMA CABQ support. Right now the EDMA TX code naively
assumes that only one frame (MPDU or A-MPDU) is being pushed into each
FIFO slot. For the CABQ this isn't true - a whole list of frames is
being pushed in - and thus CABQ handling breaks very quickly.
The aim here is to setup the CABQ list and then push _that list_ to
the hardware for transmission. I can then extend the EDMA TX code
to stamp that list as being "one" FIFO entry (likely by tagging the
last buffer in that list as "FIFO END") so the EDMA TX completion code
correctly tracks things.
Major:
* Migrate the per-TXQ add/removal locking back to per-TXQ, rather than
a single lock.
* Leave the software queue side of things under the ATH_TX_LOCK lock,
(continuing) to serialise things as they are.
* Add a new function which is called whenever there's a beacon miss,
to print out some debugging. This is primarily designed to help
me figure out if the beacon miss events are due to a noisy environment,
issues with the PHY/MAC, or other.
* Move the CABQ setup/enable to occur _after_ all the VAPs have been
looked at. This means that for multiple VAPS in bursted mode, the
CABQ gets primed once all VAPs are checked, rather than being primed
on the first VAP and then having frames appended after this.
Minor:
* Add a (disabled) twiddle to let me enable/disable cabq traffic.
It's primarily there to let me easily debug what's going on with beacon
and CABQ setup/traffic; there's some DMA engine hangs which I'm finally
trying to trace down.
* Clear bf_next when flushing frames; it should quieten some warnings
that show up when a node goes away.
Tested:
* AR9280, STA/hostap, up to 4 vaps (staggered)
* AR5416, STA/hostap, up to 4 vaps (staggered)
TODO:
* (Lots) more AR9380 and later testing, as I may have missed something here.
* Leverage this to fix CABQ hanling for AR9380 and later chips.
* Force bursted beaconing on the chips that default to staggered beacons and
ensure the CABQ stuff is all sane (eg, the MORE bits that aren't being
correctly set when chaining descriptors.)
"complete RX frames."
The 128 entry RX FIFO is really easy to fill up and miss refilling
when it's done in the ath taskq - as that gets blocked up doing
RX completion, TX completion and other random things.
So the 128 entry RX FIFO now gets emptied and refilled in the ath_intr()
task (and it grabs / releases locks, so now ath_intr() can't just be
a FAST handler yet!) but the locks aren't held for very long. The
completion part is done in the ath taskqueue context.
Details:
* Create a new completed frame list - sc->sc_rx_rxlist;
* Split the EDMA RX process queue into two halves - one that
processes the RX FIFO and refills it with new frames; another
that completes the completed frame list;
* When tearing down the driver, flush whatever is in the deferred
queue as well as what's in the FIFO;
* Create two new RX methods - one that processes all RX queues,
one that processes the given RX queue. When MSI is implemented,
we get told which RX queue the interrupt came in on so we can
specifically schedule that. (And I can do that with the non-MSI
path too; I'll figure that out later.)
* Convert the legacy code over to use these new RX methods;
* Replace all the instances of the RX taskqueue enqueue with a call
to a relevant RX method to enqueue one or all RX queues.
Tested:
* AR9380, STA
* AR9580, STA
* AR5413, STA
Since this is being done during buffer free, it's a crap shoot whether
the TX path lock is held or not. I tried putting the ath_freebuf() code
inside the TX lock and I got all kinds of locking issues - it turns out
that the buffer free path sometimes is called with the lock held and
sometimes isn't. So I'll go and fix that soon.
Hence for now the holdingbf buffers are protected by the TXBUF lock.
When working on TDMA, Sam Leffler found that the MAC DMA hardware
would re-read the last TX descriptor when getting ready to transmit
the next one. Thus the whole ATH_BUF_BUSY came into existance -
the descriptor must be left alone (very specifically the link pointer
must be maintained) until the hardware has moved onto the next frame.
He saw this in TDMA because the MAC would be frequently stopping during
active transmit (ie, when it wasn't its turn to transmit.)
Fast-forward to today. It turns out that this is a problem not with
a single MAC DMA instance, but with each QCU (from 0->9). They each
maintain separate descriptor pointers and will re-read the last
descriptor when starting to transmit the next.
So when your AP is busy transmitting from multiple TX queues, you'll
(more) frequently see one QCU stopped, waiting for a higher-priority QCU
to finsh transmitting, before it'll go ahead and continue. If you mess
up the descriptor (ie by freeing it) then you're short of luck.
Thanks to rpaulo for sticking with me whilst I diagnosed this issue
that he was quite reliably triggering in his environment.
This is a reimplementation; it doesn't have anything in common with
the ath9k or the Qualcomm Atheros reference driver.
Now - it in theory doesn't apply on the EDMA chips, as long as you
push one complete frame into the FIFO at a time. But the MAC can DMA
from a list of frames pushed into the hardware queue (ie, you concat
'n' frames together with link pointers, and then push the head pointer
into the TXQ FIFO.) Since that's likely how I'm going to implement
CABQ handling in hostap mode, it's likely that I will end up teaching
the EDMA TX completion code about busy buffers, just to be "sure"
this doesn't creep up.
Tested - iperf ap->sta and sta->ap (with both sides running this code):
* AR5416 STA
* AR9160/AR9220 hostap
To validate that it doesn't break the EDMA (FIFO) chips:
* AR9380, AR9485, AR9462 STA
Using iperf with the -S <tos byte decimal value> to set the TCP client
side DSCP bits, mapping to different TIDs and thus different TX queues.
TODO:
* Make this work on the EDMA chips, if we end up pushing lists of frames
to the hardware (eg how we eventually will handle cabq in hostap/ibss
mode.)
The HAL already included the STBC fields; it just needed to be exposed
to the driver and net80211 stack.
This should allow single-stream STBC TX and RX to be negotiated; however
the driver and rate control code currently don't do anything with it.
* Remove ar5416UpdateChainmasks();
* Remove the TX chainmask override code from the ar5416 TX descriptor
setup routines;
* Write a driver method to calculate the current chainmask based on the
operating mode and update the driver state;
* Call the HAL chainmask method before calling ath_hal_reset();
* Use the currently configured chainmask in the TX descriptors rather than
the hardware TX chainmasks.
Tested:
* AR5416, STA/AP mode - legacy and 11n modes
The default is to limit them to what the hardware is capable of.
Add sysctl twiddles for both the non-RTS and RTS protected aggregate
generation.
Whilst here, add some comments about stuff that I've discovered during
my exploration of the TX aggregate / delimiter setup path from the
reference driver.
