do not set the virtual address to the bus address when the bus
doesn't have either of the PCI_RF_DENSE or PCI_RF_BWX flags set.
The TGA driver uses the virtual address to access the registers,
which on some machines can cause a memory management fault. Map
the bus address as K0SEG virtual memory instead. Note that with
some hardware combinations involving the TGA2 adapter this change
merely results that the memory management fault is replaced by a
machine check.
this in my tree for a while and in its disabled state there are no
issues. It isn't enabled yet because some drivers (in acpi) have side
effects in their probe routines that need to be resolved in some
manner before this can be turned on. The consensus at the last
developer's summit was to provide a static method for each driver
class that will return characteristics of the driver, one of which is
if can be reprobed idempotently.
address I've lost, that move the location information to the atttach
routine as well. While one could use devinfo to get this data, that
is difficult and error prone and subject to races for short lived
devices.
Would make a good MT5 candidate.
keyword but without 'logamount' limit the amount of their log messages
by net.inet.ip.fw.verbose_limit sysctl value.
RELENG_5 candidate.
PR: kern/46080
Submitted by: Dan Pelleg
MFC after: 1 week
nor are they 3D accelarators as the description would like us to
believe. Since the TGA2 adapter has a VGA mode (unlike the TGA adapter),
one can use the VGA driver instead.
This fixes GENERIC kernels on alpha with TGA2 adapters.
page zeroing thread before it has been created. It was possible for
calls to free() very early in the boot process to panic here because
the sleep queues were not yet initialised. Specifically, sysinit_add()
running at SI_SUB_KLD would trigger this if the array of pointers
became big enough to require uma_large_alloc() allocations.
Submitted by: peter
format modules, which are currently only used on the amd64 platform.
This initial implementation just parses enough of the module to
allow it to extract dependencies and load all the bits into the
right place in memory, so the kernel must still do the full relocation
and linking. The details of the loaded sections are passed to the
kernel by supplying a copy of the ELF section header table as module
metadata with the MODINFOMD_SHDR tag.
better relocation support for the amd64 and i386 platforms. This
should not result in any change in functionality, but moves a step
towards supporting the relocatable object file modules on amd64.
The same hack/trick as load_elf*.c uses is used here to simultaneously
support both elf32 and elf64 on amd64 and i386.
operation using NET_NEEDS_GIANT(). This will result in a boot-time
restoration of Giant-enabled network operation, or run-time warning on
dynamic load (applicable only to the Netgraph component). Additional
components will likely need to be marked with this in the future.
SCSI controllers. The driver was removed before FreeBSD 3.0, so it is
probably time to remove from the Hardware Notes... :-).
Historical clue by: Josh Paetzel <josh@tcbug.org>
MFC after: 3 days
will cause the network stack to operate without the Giant lock by
default. This change has the potential to improve performance by
increasing parallelism and decreasing latency in network processing.
Due to the potential exposure of existing or new bugs, the following
compatibility functionality is maintained:
- It is still possible to disable Giant-free operation by setting
debug.mpsafenet to 0 in loader.conf.
- Add "options NET_WITH_GIANT", which will restore the default value of
debug.mpsafenet to 0, and is intended for use on systems compiled with
known unsafe components, or where a more conservative configuration is
desired.
- Add a new declaration, NET_NEEDS_GIANT("componentname"), which permits
kernel components to declare dependence on Giant over the network
stack. If the declaration is made by a preloaded module or a compiled
in component, the disposition of debug.mpsafenet will be set to 0 and
a warning concerning performance degraded operation printed to the
console. If it is declared by a loadable kernel module after boot, a
warning is displayed but the disposition cannot be changed. This is
implemented by defining a new SYSINIT() value, SI_SUB_SETTINGS, which
is intended for the processing of configuration choices after tunables
are read in and the console is available to generate errors, but
before much else gets going.
This compatibility behavior will go away when we've finished the last
of the locking work and are confident that operation is correct.
Previously, it would recognize it as a valid shell only
if the basename (nologin) was specified. Now, it will
recognize both the basename and the full path.
NOTE: The full path as adduser(8) understands it is /usr/sbin/nologin.
There is a symlink, /sbin/nologin, but that's deprecated and
only there for backwards compatibility.
ru_RU.CP866.src, the previous version of this file contained a strange
conversion error: nostr had U+255C BOX DRAWINGS UP DOUBLE AND LEFT SINGLE
instead of U+0435 CYRILLIC SMALL LETTER IE.
This way of operation is more robust than the "AI" used
before.
Add flags to mbr accessible from make.conf as BOOT_MBR_FLAGS.
Only one flag is defined now, "allow using packet mode", which
is 0x80 in accord with the rest of i386 boot code. The "packet"
flag is on by default.
PR: i386/70241
Submitted by: Valentin Nechayev <netch <@> netch.kiev.ua> (inital version)
Discussed with: jhb (by Valentin Nechayev)
Tested on: bochs (with EDD turned on or off by patching the BIOS), PCs
