Like the PNIC, we have to copy packet headers in the receive handler
because the chip will only DMA to longword aligned buffers.
Also do some mindor cleanups.
the alpha. Now the ThunderLAN driver works on the alpha (both my
sample cards check out.) Update the alpha GENERIC config to include
ThunderLAN driver now that I've tested it.
sys/alpha/conf/GENERIC.
Note: the PNIC ignores the lower few bits of the RX buffer DMA address,
which means we have to add yet another kludge to make it happy. Since
we can't offset the packet data, we copy the first few bytes of the
received data into a separate mbuf with proper alignment. This puts
the IP header where it needs to be to prevent unaligned accesses.
Also modified the PNIC driver to use a non-interrupt driven TX
strategy. This improves performance somewhat on x86/SMP systems where
interrupt delivery doesn't seem to be as fast with an SMP kernel as
with a UP kernel.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Iprobe is an alpha-only system profiling suite which I'm porting from
Linux/alpha to FreeBSD.
Iprobe works by using the hardware profiling support built into
alpha cpus. In a nutshell, what Iprobe does is to setup the alpha
performance counters to sample the pc at a fairly high rate & dumps
those pc samples out to user space. Then some code runs to map the
sampled PCs to functions. You get a bit more than that (like the PSL
word, so you can tell if you're in the kernel or userland, what the
ipl is, etc).
o Add the EB64PLUS systype into the kernel configuration files
and add it to the GENERIC kernel
o Correct mcclock_isa.c's dependence on cia, it should depend on isa.
This will allow avanti and eb64+ kernels to be built without the cia
chipset support code.
than ".so". The old extension conflicted with well-established
naming conventions for dynamically loadable modules.
The "clean" targets continue to remove ".so" files too, to deal with
old systems.
that the generated files are generated before any of the object files.
Also minor cleanup of dependencies in conf/files that I bogusly added
before.
This should fix the requirement that make depend be done starting from
a clean config directory. If you don't have a clean directory, make
depend is still required if you want the proper .o's to be recompiled.
Reviewed by: bde
alpha, operations involving non-finite numbers or denormalised numbers
or operations which should generate such numbers will cause an arithmetic
exception. For programs which follow some strict code generation rules,
the kernel trap handler can then 'complete' the operation by emulating
the faulting instruction.
To use software completion, a program must be compiled with the arguments
'-mtrap-precision=i' and '-mfp-trap-mode=su' or '-mfp-trap-mode=sui'.
Programs compiled in this way can use non-finite and denormalised numbers
at the expense of slightly less efficient code generation of floating
point instructions. Programs not compiled with these options will receive
a SIGFPE signal when non-finite or denormalised numbers are used or
generated.
Reviewed by: John Polstra <jdp@polstra.com>
and dies if it can't find the MFS root whereas the x86 one seems to sail
past. Looking at the code, I can't see how either one works, so I'm
confused. :)
* Support for AlphaStation 200, 250, 255, 400
* Untested support for UDB, Multia, AXPpci33 (Noname)
* Support for Personal Workstation 433a/433au, 500a/500au, 600a/600au (Miata)
* Some minor fixes and improvements to interrupt handling.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu> (AS200, Miata)
Obtained from: NetBSD (some code for AS200, Miata, Noname)
