etc.). The tulip_start routine was rewritten to use less stack space (I've
been having problems with wcarchive overflowing the stack and this should
help a little). This version also has preliminary NetBSD support.
Rod Grimes helped in testing this version of the driver. Thanks Rod. It's
additionally been extensively tested here and on wcarchive.
Submitted by: Matt Thomas
to most users (the wrong length is passed to ether_input). The
second is more serious. The multicast hash algorithm uses the wrong
(low) bits instead of the right (high) bits. This is only an issue
if you use >12 multicast addresses but if you are using IP multicast
then it might affect you...
Submitted by: Matt Thomas
thrown out if bpfilter support and no BPF listener. (submitted by Bill
Fenner)
Removed unused variable and changed another from a stack variable to a
static - the variable was a rather large array of structs that consumed
a lot of stack space. (me)
1) If a target initiated a sync negotiation with us and happened to chose a
value above 15, the old code inadvertantly truncated it with an "& 0x0f".
If the periferal picked something really bad like 0x32, you'd end up with
an offset of 2 which would hang the drive since it didn't expect to ever
get something so low. We now do a MIN(maxoffset, given_offset).
2) In the case of Wide cards, we were turning on sync transfers after a
sucessfull wide negotiation. Now we leave the offset alone in the per
target scratch space (which implies asyncronous transfers since we initialize
it that way) until a syncronous negotation occurs.
3) We were advertizing a max offset of 15 instead of 8 for wide devices.
4) If the upper level SCSI code sent down a "SCSI_RESET", it would hang the
system because we would end up sending a null command to the sequencer. Now
we handle SCSI_RESET correctly by having the sequencer interrupt us when it
is about to fill the message buffer so that we can fill it in ourselves.
The sequencer will also "simulate" a command complete for these "message only"
SCBs so that the kernel driver can finish up properly. The cdplay utility
will send a "SCSI_REST" to the cdplayer if you use the reset command.
5) The code that handles SCSIINTs was broken in that if more than one type
of error was true at once, we'd do outbs without the card being paused.
The else clause after the busfree case was also an accident waiting to
happen. I've now turned this into an if, else if, else type of thing, since
in most cases when we handle one type of error, it should be okay to ignore
the rest (ie if we have a SELTO, who cares if there was a parity error on
the transaction?), but the section should really be rewritten after 2.0.5.
This fix was the least obtrusive way to patch the problem.
6) Only tag either SDTR or WDTR negotiation on an SCB. The real problem is
that I don't account for the case when an SCB that is tagged to do a particular
type of negotiation completes or SELTOs (selection timeout) without the
negotiation taking place, so the accounting of sdtrpending and wdtrpending
gets screwed up. In the wide case, if we tag it to do both wdtr and sdtr,
it only performs wdtr (since wdtr must occur first and we spread out the
negotiation over two commands) so we always have sdtrpending set for that
target and we never do a real SDTR. I fill properly fix the accounting
after 2.0.5 goes out the door, but this works (as confirmed by Dan) on
wide targets.
Other stuff that is also included:
1) Don't do a bzero when recycling SCBs. The only thing that must explicitly
be set to zero is the scb control byte which is done in ahc_get_scb. We also
need to set the SG_list_pointer and SG_list_count to 0 for commands that do
not transfer data.
2) Mask the interrupt type printout for the aic7870 case. The bit we were
using to determine interrupt type is only valid for the aic7770.
Submitted by: Justin Gibbs
the 802.3 frames generated by the DC21040 (which does automatic padding
of less-than-minimum frames) and the frames generated by the 'ed'
driver, I've found that there is indeed a bug in the size of "ETHER_MIN_LEN"
as reported by several people, John Hay being the most recent. The driver
was actually setting the length to 6+6+2+50 (64 bytes), which when adding
in the CRC (which is automatically appended to the frame and not included
in the length), the minimum frame is 4 bytes larger than it is supposed to
be. All of this is confirmed by tcpdump showing 50 bytes of data for
minimum frames from the 'ed' cards and 46 bytes from 'de' cards. This
analysis has also revealed that there is garbage in the un-filled in
portion at the end of the minimum frames from the 'ed' driver; I don't
plan to fix this.
The ``flags 1'' in the fdc line is now only needed for owners of an
Insight tape (perhaps there aren't any? Mine is disfunctional). All
other probes are safe wrt. to the motor-control line of floppy disk
drives. Document the flag in LINT finally.
fragmented.
Added support for Cogent em100 boards.
Fixed bug that caused BPF to toggle the card to UTP.
Various other improvements.
Submitted by: Matt Thomas and David Greenman
the adapter's selections. Many fast periferals were getting upset when
the sequencer decided to rearbitrate after the device had already won
arbitration. This also forced the creation of a list threaded through
the SCBs (since we don't have enough space anywhere else) of commands that
are awaiting reselection. This list is run down before any new transactions
from the input queue are allowed. The list is appened to whenever we begin
a selection (simple case since the selecting device is always at the head)
and by the kernel driver whenever a request sense occurs. In the common
case, the list is only one element long, but when a reselection wins out
over a selection and that reselection generates a request sense, the
outstanding selection required for the retreval of the sense code grows
the list. On machines with many targets, this might cause the list to grow
large, so this solution, which will allow up to the maximum number of I/O
requests capible of the card elements in the list, was chosen. The list
manipulation is trivial and adds three sequencer instructions of overhead
to the selection phase.
This fixes the "target busy" errors from micropolis drives and the bursty
I/O problem when performing I/O between a Quantum Grand Prix and any other
device. I anticipate that this will correct many of the problems that
have been reported with this driver.
Reviewed by: Wcarchive and David Greenman
don't expect this to work yet.. but at least they're here..
(hey this cvs stuff is fun!)
activate with a line exactly like the isa line in the config file,
(but specifying eisa :)
patches to come..
got a 2.2 version DC21040 chip in my SMC ethernet card! He suggests bumping
the check all the way down to 2.0 since it's pre-2.0 we're actually guarding
against.
Submitted by: Matt Thomas <matt@lkg.dec.com>
is identical to the older version, just the copyright has changed. Many
thanks go to Dean Gehnert of the Linux camp who went the extra mile to make
this happen.
Other changes:
Update assembler man page to include the -v and -D options
Merge in Dean's latest changes to the assembler
Have the sequencer do a MSG_REJECT when the negotiated syncronous rate
is lower than the adapter supports. This forces asyncronous mode which
is faster at these rates anyway.
This code will be moved shortly to the non-gpld portion of the tree.
Dropping into the debugger when a break comes down the serial line is a
>MISFEATURE (1st class)< and has been put under it's own #ifdef. This
should be a magic sequence of chars instead.
For those where it was easy, drivers were also fixed to call
dev_attach() during probe rather than attach (in keeping with the
new design articulated in a mail message five months ago). For
a few that were really easy, correct state tracking was added as well.
The `fd' driver was fixed to correctly fill in the description.
The CPU identify code was fixed to attach a `cpu' device. The code
was also massively reordered to fill in cpu_model with somethingremotely
resembling what identifycpu() prints out. A few bytes saved by using
%b to format the features list rather than lots of ifs.
old type (stty) ioctls can easily bypass locking bits.
It involves manual conversion from old ioctls to new ones,
large piece of code duplicated from tty_compat.c
after ttioctl too, because it can change t_line.
Remove (TS_CNTTB | TS_LNCH) test, it is always inherits from
old tty mode and can't be reach in currently setted mode.
old value.
Remove unnecessary check for active messages in setup SCB. This same test
would also jump to p_mesgin_done which would "ACK" an extra time possibly
confusing the target.
Tell the kernel driver whenever we send an ABORT_TAG message.
- Report valid residual byte counts. We actually pause the sequencer
when the residual is non-zero. I thought about using DMA to do this,
bus sequencer program space is tight.
- Fix embarassing off by one error in the computation of a 2's
compliment variable. This was most likely the cause of the
many problems reported with the tagged queuing code.
- Handle "MAX_SYNC" as a special case (ie we are the ones starting
the sync negotiation sequence). This was done so that the target
scratch area can be initialed to 0 offset (asyncronous transfers)
safely. The initialization to 0 (was 15) is necessary since in
some cases a Wide negotiation could run into problems if SCSIRATE
was set wrong and we went into data(in/out).
- Trim the DMA routines a little by using some procedures. Net
effect is more functionality with 3 less instructions after this
update.
- Toggle the WIDEODD bit of the DFCNTRL whenever this is not the
last SG block. It has no effect in the 8bit bus configuration,
but in the Wide configuration ensures that the overlap byte is
held in the SCSI block if the transfer is odd so it will end
up in the next SG (the correct behavior).
* to reduce the number of adapter failures. Transceiver select
* logic changed to use value from EEPROM. Autoconfiguration
* features added.
Submitted by: "Serge A. Babkin" <babkin@hq.icb.chel.su>
update what has actually been touched. This should speed up
screen access on slow hardware.
Introduced setting of "destructive" cursor size, much like
the old hardware cursor.
if (tp->t_line != 0)
test when CS_ODONE, it fails for NTTYDISC, use
if (linesw[tp->t_line].l_start != ttstart)
instead.
Reviewed by:
Submitted by:
Obtained from:
CVS:
BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
include <pci/pcivar.h> without including <sys/devconf.h> and other
drivers include <pci/pcivar.h> before including <sys/devconf.h> if
certain identifiers are defined.
The devconf headers have convoluted interdependencies. <sys/devconf.h>
includes <machine/devconf.h> which includes <pci/pcivar.h>. Most
drivers include <sys/devconf.h> so even isa drivers depend on
<pci/pcivar.h>. For similar reasons, most drivers depend on another
pci header, on an isa header and on two scsi headers.
NOT derived from the Linux code and is thus not GPL'd. It is the author's
express wish that the GPL copyrighted version be removed and this BSD copyright
version take its place. Considering our own stance on this, I'm certainly
not going to argue! [Note to NetBSD folks: You're free to grab it now :-)]
Submitted by: Mikael Hybsch <micke@dynas.se>
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
1) Supports PCI to PCI bridge devices (and tries to initialise them,
even if the BIOS is brain dead).
2) Supports shared PCI interrupts. Interrupt handlers now MUST return
'0' if they found nothing to do, '1' otherwise.
New features tested with i486 systems based on the Intel Saturn and
a DEC 4channel Ethernet card only, but expected to work on most systems.
The option PCI_REMAP has been removed !
Submitted by: Wolfgang Stanglmeier <wolf@kintaro.cologne.de>
a device specific shutdown routine for devconf. Assign the value of this
to the kern_devconf struct. Implement a device shutdown routine for if_de
that disables the device. This will stop the device from corrupting memory
after a reboot.
Let "grey delete" be a function key (default is 0x7f)
Fix the xor cursor again..
Made the backspace key generate del as default
Made CTRL-space generate nul as default.
(a) bring back ttselect, now that we have xxxdevtotty() it isn't dangerous.
(b) remove all of the wrappers that have been replaced by ttselect
(c) fix formatting in syscons.c and definition in syscons.h
(d) add cxdevtotty
NOT DONE:
(e) make pcvt work... it was already broken...when someone fixes pcvt to
link properly, just rename get_pccons to xxxdevtotty and we're done
DEC 21050 chip in particular, don't have specs of other such chips).
This should add support for Multiple-Ethernet PCI cards (e.g. Znyx 314).
Reviewed by: se
Submitted by: <wolf@kintaro.cologne.de> Wolfgang Stanglmeier
is close to 1000000 / 960 usec so the confusion probably didn't matter.
Test for COMCONSOLE before testing for RB_SERIAL so that the RB_SERIAL
test can be optimized away if COMCONSOLE is 1.
Simplify and Uniformize style of previous commit.
(b) add a function callback vector to tty drivers that will return a pointer
to a valid tty structure based upon a dev_t
(c) make syscons structures the same size whether or not APM is enabled so
utilities don't crash if NAPM changes (and make the damn kernel compile!)
(d) rewrite /dev/snp ioctl interface so that it is device driver and i386
independant
labels.
Please test the slice/label features:
cd /dev; sh MAKEDEV svn0
cd /var/tmp; dd if=/dev/zero of=vnfile bs=8192 count=1024
vnconfig -c /dev/rvn0 /var/tmp/vnfile
fdisk /dev/rvn0 # invent a geometry, create one BSD partition
disklabel -r -w vn0 floppy # a convenient (bogus) label
disklabel -e vn0 # edit label to match device
newfs /dev/rvn0a
mount /dev/vn0a /mnt
...
The steps after the fdisk could name the device vn0s1 instead of vn0.
PCI BIOS mappings are retained, except if option PCI_REMAP
is specified in the kernel config file.
There is now a list of attach addresses, and the first
address that seems to make some device registers appear
is chosen.
Reviewed by: se
Submitted by: wolf
Removed screensavers from syscons, they are now LKM's. This makes it
possible to do some really "interesting" screensavers...
Fixed bug that sometimes caused garbage to appear when leaving
"scroll-lock" history.
Reformattet indentation, it got too deep for a normal 80 pos screen.
Split up in syscons.c & syscons.h for use with the saver-lkm's.
Temporarily removed -s option from vidcontrol, savers should now
be loaded with modload.
briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <hosokawa@mt.cs.keio.ac.jp>
when ttselect() is improved. This requires using an array of tty structs
and not using ttymalloc().
Fix an off by 1 error. Some caclulations seem to be off by a factor
of NCY. NCY defaults to 16, which gives 256 tty structs occupying
0xd000 bytes. The minor number encoding only allows 16 ttys.
Update the types of timeout functions to 2.0.
- Overflow now calculated right
- Close works ok,does not looses tty
- Better overflow handling now the snooping stops
on overflow,but programm notified and can reconnect if
it want to..Default maximal buffer set to 664 K and this
is probably too much..:)))
Utility still to come
New config option "NCR_IOMAPPED" makes the driver use port I/O.
Put back in 53c815 defines, submitted by Mikael Hybsch <micke@dynas.se>.
These had got lost between cvs rev. 1.14 and now ...
pci.c:
Really write config space register.
Assign ports starting at 0xbc00.
Submitted by: wolf
Reviewed by: se
Users-beware..
It is tested and working for me but probably have some bugs i
didn't noticed so test it and reply...
It can:
look at what's sent to the user from tty device
snoop on pty's,vty's and serial tty's
It (still) can't:
write to tty
see what user types in local echo mode
It is probably bad styled and
very dependant on tty_pty.c,sio.c and syscons.c
I would be really happy if another ppl would make their
changes because i am not sure this is the best snoop
we can have..but it is good..:)))))
so that the interface won't have the effect of blocking other senders
during bulk transfers (i.e. hogging the ethernet). It improves performance
in all of my tests by reducing collisions and I believe it to be a Good
Thing.
adapted to FreeBSD by Heikki Suonsivu <hsu@cs.hut.fi>.
Submitted by: Andrew Werple <andrew@werple.apana.org.au> and
Heikki Suonsivu <hsu@cs.hut.fi>
Obtained from: NetBSD
definitions taken from the PCI specs. Part of them were typed
in by Wolfgang Stanglmeier, the (at that time unneeded) rest
by Charles Hannum (thanks !).
