with macros. This breaks if the functions are replaced by macros with
unsuitable semantics. Define a MAX() macro unconditionally instead.
max() is unsuitable since we need a constant expression. Don't define
MIN() - we never used min().
is "acquired". This fixes a TSC biasing error of about 10 msec when
pcaudio is active.
Update `time' before calling hardclock() when timer0 is being released.
This is not known to be important.
Added some delays in writertc(). Efficiency is not critical here, unlike
in rtcin(), and we already use conservative delays there.
Don't touch the hardware when machdep.i8254_freq is being changed but
the maximum count wouldn't change. This fixes jitter of up to 10 msec
for most small adjustments to machdep.i8254_freq. When the maximum
count needs to change, the hardware should be adjusted more carefully.
this using option "-b" to the boot blocks. It is smartest to compile
a font into your kernel (See LINT), but not mandatory, but apart from
the cursor you will see nothing on the screen until you load a font.
This mode allows XF86_VGA16 to run in 800x600 mode on otherwise unsupported
graphics hardware.
A number of buglets in the cursor handling in syscons may become
visible this way.
mode switch in ioctl.
Possibly related to PR: kern/4271
- A kludge: initialize scp->xpixel and ypixel even in the text mode.
If the console enters the `unknown' graphics mode via the ioctl KDSETMODE
(KD_GRAPHICS), these fields are not set (because syscons cannot know
the correct values), but set_mouse_pos() need to refer to these field
to adjust the mouse position.
- Turn off MOUSE_VISIBLE when switching video mode by ioctl.
- another new option: SC_MOUSE_CHAR
Define the first character code of four consecutive codes to be used for
the mouse cursor. Default codes are 0xd0 through 0xd3. Beware that
if you decide to use any codes outside the range of 0xc0-0xdf,
the mouse cursor may not look good, because of the way VGA displays
characters in 9-dot-wide character cells.
Requested by several people.
(This patch was tested by a person who recently reported, in the -current
ML, a page fault problem in the kernel (draw_mouse_iamge()) after
X server shutdown. The patch cured his problem.)
Don't touch/update the screen while manipulating font data.
Possibly related to PR: kern/4271
- Set up VGA in alphanumeric mode rather than graphics mode when
loading font into video memory. This will drastically reduce flicker.
PR: bin/2977
- Set up scp->font_size properly during video mode switch caused by
ioctl.
separate routine: scupdate() called from scrn_timer().
- Make sure that the screen is updated for the low-level console
routines sccngetc() and sccncheckc(). A new routine, sccnupdate(),
is introduced and will call scupdate() above.
Requested by: bde and msmith
OKed by: sos
from the low-level console routines sccngetc() and sccncheckc().
Submitted by: bde (a long time ago)
- Don't try to ring bell and immediately return from do_bell() while
device probe is in progress at boot time; the timeout queue is not
functional yet.
PR: kern/2424
- Stop running the screen saver after panic() is called: check
if `panicstr' is non-NULL during scrn_timer().
PR: kern/5314
- A new option: SC_DISABLE_REBOOT
The reboot key (usually Ctl-Alt-Del) will be ignored if this option
is defined. You may still have the reboot key defined in the keymap and
it won't cause error when the keymap is loaded, but it will be quietly
treated as nop.
OKed by: sos
This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
so that existing programs which were compiled before the introduction
of the new mouse code and use these ioctls will run unmodified.
Suggested by msmith.
(accent_key + space does still print the accent letter too, as in
the previous commit.)
Requested by a couple of users.
- Clear the accent flag when the next_screen key is pressed.
- Added some comment lines regarding accent key processing.
- IIR_TXRDY is never off even if reading a IIR register.
- Know as PIAFS "Palido 321S", "DC-*S" oemed by Sharp corp.
2. Omiting a restrict probing if it's already probed by pccardd.
Note: Define a new id_flags as follows
0x40000 - NO PROBE (Already probed as serial)
0x80000 - Has a bogus IIR_TXRDY register
Sato Junichi <junichi@astec.co.jp>
Nrihiro Kumagai <kuma@slab.tnr.sharp.co.jp>
Hirao Tetsuya <ai.cs.fujitsu.co.jp>
Toshiharu Asai <asai@mbc.infoshere.or.jp>
Shin'ya Kumabuchi <kumabu@t3.rim.or.jp>
Freebsd-users-jp@jp.freebsd.orgbsd-nomads@ai.cs.fujitsu.co.jp
With a keymap with accent key definitions loaded to syscons, you press
an accent key followed by a regular letter key to produce an accented
letter. Press an accent key followed by the space bar to get the
accent letter itself.
Code is based on the ideas and work by jmrueda@diatel.upm.es and
totii@est.is.
PR: i386/4016
console.h
- Defined structures and constants for accent (dead) keys.
syscons.c, kbdtables.h
- When an accent key is pressed, set the corresponding index to
`accents'. If the next key is the space key, produce the accent char
itself. Otherwise search the accent key map entry, indexed by
`accents', for a matching pair of a regular char and an accented char.
- Added ioctl functions to set and get the accent key map (PIO_DEADKEYMAP
and GIO_DEADKEYMAP).
necessary to call it when the tty layer's output state has not been
changed, but siostop() sometimes changes the TS_BUSY state and then
calls comstart() mainly for its side effect of calling ttwwakeup().
MS IntelliMouse, Kensington Thinking Mouse, Genius NetScroll,
Genius NetMouse, Genius NetMouse Pro, ALPS GlidePoint, ASCII
MieMouse, Logitech MouseMan+, FirstMouse+
- The `psm' driver is made to recognize various models of PS/2 mice
and enable their extra features so that their additional buttons and
wheel/roller are recognized. The name of the detected model will be
printed at boot time.
- A set of new ioctl functions are added to the `psm', `mse' and
`sysmouse' drivers so that the userland program (such as the X server)
can query device information and change driver settings.
- The wheel/roller movement is handled as the `Z' axis movement by the
mouse drivers and the moused daemon. The Z axis movement may be mapped
to another axis movement or buttons.
- The mouse drivers support a new, standard mouse data format,
MOUSE_PROTO_SYSMOUSE format which can encode x, y, and x axis movement
and up to 10 buttons.
/sys/i386/include/mouse.h
- Added some fields to `mousestatus_t' to store Z axis movement
and flag bits.
- Added the field `model' to `mousehw_t' to store mouse model code.
Defined model codes.
- Extended `mousemode_t'.
- Added new protocols and some constants for them.
- Added new ioctl functions and structures.
- Removed obsolete ioctl definitions.
/sys/i386/include/console.h
- Added `dz' field to the structure `mouse_data' to pass Z axis movement
to `syscons/sysmouse'.
- Removed LEFT_BUTTON, MIDDLE_BUTTON and RIGHT_BUTTON. Use button bits
defined in `mouse.h' instead.
/sys/i386/isa/psm.c
- Added a set of functions to detect various mice which have additional
features (wheel and buttons) unavailable in the standard PS/2 mouse.
- Refined existing ioctl functions and added new ones. Most important
of all is MOUSE_SETLEVEL which manipulates the output level of the driver.
While the output level remains zero, the output from the `psm' driver is
in the standard PS/2 mouse format (three bytes long). When the level
is set to one, the `psm' driver will send data in the extended format.
At the level two the driver uses the format which is native to the
connected mouse is used. (Meaning that the output from the device is
passed to the caller as is, unmodified.) The `psm' driver will pass
such extended data format as is to the caller if the output level is
two, but emulates the standard format if the output level is zero.
- Added kernel configuration flags to set initial resolution
(PSM_CONFIG_RESOLUTION) and acceleration (PSM_CONFIG_ACCEL).
- Removed the compile options PSM_ACCEL, PSM_CHECKSYNC and PSM_EMULATION.
Acceleration ratio is now specified by the kernel configuration flags
stated above. Sync check logic is refined and now standard.
The sync check can be turned off by the new kernel configuration flags
PSM_CONFIG_NOCHECKSYNC (0x100). PSM_EMULATION has been of little use.
- Summer clean up :-) Removed unused code and obsolete comments.
/sys/i386/isa/mse.c
- Created mseioctl() to deal with ioctl functions MOUSE_XXXX.
Most importantly, the MOUSE_SETLEVEL ioctl will change the
output format from the 5 byte format to the new, extended format
so that the caller can take advantage of Z axis movement and additional
buttons.
- Use constants defined in `mouse.h' rather than magic numbers.
/sys/i386/isa/syscons.c
- Changed scioctl() to reflect the new `console.h' and some of the new
ioctls defined in `mouse.h'. Most importantly, the MOUSE_SETLEVEL
ioctl will change the `sysmouse' output format from the MouseSystems
5 byte format to the new, extended format so that the caller can
take advantage of Z axis movement and additional buttons.
- Added support for double/triple click actions of the left button and
single click action of the right button in the virtual console. The
left button double click will select a word under the mouse pointer.
The triple click will select a line and the single click of the right
button will extend the selected region to the current position of
the mouse pointer. This will make the cut/paste support more compatible
with xterm.
/sys/i386/isa/kbdio.h
- Added PSM_INTELLI_ID.
checking the BIOS video mode paramter table. Now syscons uses the
parameter table even if some bits in the table are different from the
current VGA register settings.
Even if comp_vgaregs() finds that the BIOS video parameter table looks
totally unfamiliar to it, syscons allows the user to change the
current video mode to some modes which are based on the VGA 80x25
mode. They are VGA 80x30, VGA 80x50, VGA 80x60. In this case the user
will be warned, during boot, that video mode switching is only
paritally supported on his machine.
PR: bin/4477
in <machine/cpu.h>. Moved the declarations to <machine/cputypes.h>.
Fixed style bugs in the moved code. Fixed everything that depended on
the nested include. Don't include <machine/cpu.h> (in the changed files)
unless something in it is used directly.
use a Linker Set. Note, if a driver is loaded as an LKM if will have
to use the function call, but since none of the existing drivers
are loadable, this made things cleaner and boot messages nicer.
Obtained from: PAO-970616
flicker won't occur when set_border() is called.
- Properly restore the border color when switching virtual consoles.
Pointed out by: tony@dell.com
OKed by: sos
* Kill individual drivers 'suspend' routines, since there's no simple/safe
way to suspend/resume a card w/out going through the complete probe
at initialization time.
* Default to using the apm_pccard_resume sysctl code, which basically
pretends the card was removed, and then re-inserted. Suspend/resume
is now 'emulated' with a fake insert/removal. (Hence we no longer
need the driver-specific suspend routines.)
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
check the value and caused kernel panic when a large value was given.
- Move the configuration option SC_HISTORY_SIZE from syscons.h to
syscons.c.
- Define the maximum total number of history lines of all consoles.
It is SC_HISTORY_SIZE*MAXCONS or 1000*MAXCONS; whichever is larger.
CONS_HISTORY will allow the user to set the history size up to
SC_HISTORY_SIZE unconditionally (or the current height of the console
if it is larger than SC_HISTORY_SIZE). If the user requests a larger
buffer, it will be granted only if the total number of all allocated
history lines and the requested number of lines won't exceed the maximum.
- Don't free the previous history buffer and leave the history buffer
pointer holding a invalid pointer. Set the pointer to NULL first, then
free the buffer.
PR: bin/4592
floppy drive #0, regardless of what the CMOS says. This is intended
as a bandaid for those plagued with Compaq's idea to not announce the
floppy drive on their `Aero' notebook.
Using the device flags is not very nice (in particular since they
aren't per-drive but per-controller), but still looks a lot better to
me than the disgusting guesswork hack that was recently posted to
-hackers.
Doc update will follow shortly.
Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
internal modems. Currently detects a USR modem, and a couple Supra
modems... vendor id's for sio capabile cards welcomed...
document new option EXTRA_SIO that will increase sio's internal data
structures to support X more serial ports... these are used by the
PnP part of sio for attaching... If you don't have it specified, it
will default to 2... This is defaulted to 0 if you don't have PnP
compiled into your kernel...
also document that if you set the PnP flags (pnp x flags y) to 0x1 that
the modem will be refused to be recognized by the sio driver... this
is for people that want the traditional isa driver to probe and attach
the modem... (for keeping legacy sio numbering)
