src/lkm/Makefile.inc. This fixes broken builds of the syscons LKMs
when OBJFORMAT=elf. Removed src/lkm/Makefile.inc since it became
empty and is worse than useless.
arguments as appropriate. This is necessary because setting OBJFORMAT=aout
in the makefile doesn't get exported to the environment. I wish our
make could do that!
- Implement a new copyin/readin interface for loading modules.
This allows the module loaders to become MI, reducing code duplication.
- Simplify the search for an image activator for the loaded kernel.
- Use the common module management code for all module metadata.
- Add an 'unload' command that throws everything away.
- Move the a.out module loader to MI code, add support for a.out
kld modules.
Submitted by: Alpha changes fixed by Doug Rabson <dfr@freebsd.org>
Removed Hauppauge EEPROM 0x10 detection as I think 0x10 should be a
PAL tuner, not NTSC.
Reinstated some Tuner Guesswork code from 1.27
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Added PR kern/7177 for SECAM Video Highway Xtreme with single crystal
PLL configuration submitted by Vsevolod Lobko <seva@alex-ua.com>.
In kernel configuration file add
options OVERRIDE_CARD=2
options OVERRIDE_TUNER=11
options BKTR_USE_PLL
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Normally the full 640x480 (768x576 PAL) image is grabbed. This ioctl
allows a smaller area from anywhere within the video image to be
grabbed, eg a 400x300 image from (50,10).
See restrictions in BT848SCAPAREA.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
cluster from the RX descriptor is passed up to the higher layers and
replaced with an empty buffer for the next time the descriptor comes
up in the RX ring. The xl_newbuf() routine returns ENOBUFS if it can't
obtain a new mbuf cluster, but this return value was being ignored.
Now, if buffer allocation fails, we leave the old one in place and
drop the packet. This is rude, but there's not much else that can be
done in this situation.
Without this, the driver can cause a panic if the system runs out of
MBUF clusters. Now it will complain loudly, but it shouldn't cause a
panic.
Also added another pair of missing newlines to some printf()s.
- moved definition of MACHINE_ARCH from cpu.h to parm.h as alpha.
- Added definitions of _MACHINE and _MACHINE_ARCH.
- Added hw.ispc98. The hw.ispc98 is 1 in PC98 kernel and is 0 in
IBM-PC kernel.
Discussed with: John Birrell <jb@FreeBSD.ORG>
XFree86 server, users need to create the following links in their
/compat/linux/dev directory (assuming kernel configured with 4 VTs).
lrwxrwxrwx 1 root wheel 7 Aug 30 22:59 tty0 -> console
lrwxrwxrwx 1 root wheel 5 Aug 30 22:45 tty1 -> ttyv0
lrwxrwxrwx 1 root wheel 5 Aug 30 22:45 tty2 -> ttyv1
lrwxrwxrwx 1 root wheel 5 Aug 30 22:45 tty3 -> ttyv2
lrwxrwxrwx 1 root wheel 5 Aug 30 22:45 tty4 -> ttyv3
VT switching is still not yet supported. Attempting to switch VT
currently will cause Xserver bus error.
Submitted by: Chain Lee <chain@110.net>
delay controls how long the driver waits for autonegotiation to
complete after setting the 'autoneg restart bit' in a PHY. In some
cases, it seems 3 seconds is not long enough: with 3c905-TX cards
(external PHY), you sometimes see 'autoneg not complete; no carrier'
errors due to the timeout being too short. (3c905B adapters seem to
be happy with 3 seconds though.)
a kernel be built and installed at just the right time. If the system
were to be rebooted after installing the 3.0 binaries without the
new kernel, the system is hosed.
The addition of this config file reserves the name of the config file
that the upgrade procedure uses. If an upgrade is to be performed on
a 2.2.5/6/7 system system for which a GENERIC kernel is inadequate,
this config file must be replace with a suitable one before performing
the upgrade.
On systems which report 'uname -r' as 3.0-CURRENT, the kernel build
is not performed and this file is ignored.
Add a sysctl 'machdep.cs_recv_delay' to specify how long to wait after
receiving a packet in order to check for a subsequent (back-to-back)
packet. The cs8900 has a very small receive buffer, so this helps avoid
overflows at the cost of some extra CPU overhead.
Submitted by: Oleg Sharoiko <os@rsu.ru>, MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
We do the same thing we do with all the other Vadem chips and print the
right identification for these chips. Tested with the 365, and inferred
for the 465.
This allows the cheapo PCMCIA card that I got from necx to print the right
chip number on boot.
