mutex releases to not require flags for the cases when preemption is
not allowed:
The purpose of the MTX_NOSWITCH and SWI_NOSWITCH flags is to prevent
switching to a higher priority thread on mutex releease and swi schedule,
respectively when that switch is not safe. Now that the critical section
API maintains a per-thread nesting count, the kernel can easily check
whether or not it should switch without relying on flags from the
programmer. This fixes a few bugs in that all current callers of
swi_sched() used SWI_NOSWITCH, when in fact, only the ones called from
fast interrupt handlers and the swi_sched of softclock needed this flag.
Note that to ensure that swi_sched()'s in clock and fast interrupt
handlers do not switch, these handlers have to be explicitly wrapped
in critical_enter/exit pairs. Presently, just wrapping the handlers is
sufficient, but in the future with the fully preemptive kernel, the
interrupt must be EOI'd before critical_exit() is called. (critical_exit()
can switch due to a deferred preemption in a fully preemptive kernel.)
I've tested the changes to the interrupt code on i386 and alpha. I have
not tested ia64, but the interrupt code is almost identical to the alpha
code, so I expect it will work fine. PowerPC and ARM do not yet have
interrupt code in the tree so they shouldn't be broken. Sparc64 is
broken, but that's been ok'd by jake and tmm who will be fixing the
interrupt code for sparc64 shortly.
Reviewed by: peter
Tested on: i386, alpha
It is legal to have a device with device type 0x1f, that just means
that the device is of unknown type. Instead, only check the peripheral
qualifier when deciding whether or not to reject a device based on its
inquiry information.
Tested by: julian
MFC after: 3 weeks
time in the cases where it really sends the drive out to lunch, but it also
allows us to catch very wierd edge cases of strange drives that might take
a very long time (emulated disk drives over a network, e.g.).
quirk regarding the C- series makes me suspect that all Olympus models have
the same quirks, but I cannot prove it.
Submitted by: Bernd Walter <ticso@cicely8.cicely.de>
attempts to set buffered mode was printing out "unable to set buffered
mode" no matter what. Oops.
Spotted by: Joerg Wunsch <joerg_wunsch@uriah.heep.sax.de>
MFC after: 3 weeks
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
Clear residual counts after a successful samount (the user doesn't
care that we got an N-kbyte residual on our test read).
Change a lot of error handling code.
1. If we end up in saerror, check more carefully about the kind of
error. If it is a CAM_SCSI_STATUS_ERROR and it is a read/write
command, we'll be handling this in saerror. If it isn't a read/write
command, check to see whether this is just an EOM/EOP check condition-
if it is, just set residual and return normally. A residual and
then a NO SENSE check condiftion with the ASC of 0 and ASCQ of
between 1 and 4 are normal 'signifying' events, not errors per se,
and we shouldn't give the command to cam_periph_error to do something
relatively unpredictable with.
2. If we get a Bus Reset, had a BDR sent, or get the cam status of
CAM_REQUEUE_REQ, check the retry count on the command. The default
error handler, cam_periph_error, doesn't honor retry count in these
cases. This may change in the future, but for now, make sure we
set EIO and return without calling cam_periph_error if the retry
count for the command with an error is zero.
3. Clean up the pending error case goop and handle cases more
sensibly.
The rules are:
If command was a Write:
If we got a SSD_KEY_VOLUME_OVERFLOW, the resid is
propagated and we set ENOSPC as the error.
Else if we got an EOM condition- just mark EOM pending.
And set a residual of zero. For the longest time I was just
propagating residual from the sense data- but my tape
comparison tests were always failing because all drives I
tested with actually *do* write the data anyway- the EOM
(early warning) condition occurred *prior* to all of the
data going out to media- that is, it was still buffered by
the drive. This case is described in SCSI-2, 10.2.14,
paragraph #d for the meaning of 'information field'. A
better fix for this would be to issue a WFM command of zero
to cause the drive to flush any buffered data, but this
would require a fairly extensive rewrite.
Else if the command was a READ:
If we got a SSD_KEY_BLANK_CHECK-
If we have a One Filemark EOT model- mark EOM as pending,
otherwise set EIO as the erorr.
Else if we found a Filemark-
If we're in Fixed Block mode- mark EOF pending.
If we had an ILI (Incorrect Length Indicator)-
If the residual is less than zero, whine about tape record
being too big for user's buffer, otherwise if we were in
Fixed Block mode, mark EIO as pending.
All 'pending' conditions mean that the command in question completes
without error indication. It had succeeded, but a signifying event
occurred during its execution which will apply to the *next* command
that would be exexcuted. Except for the one EOM case above, we always
propagate residual.
Now, way back in sastart- if we notice any of the PENDING bits set,
we don't run the command we've just pulled off the wait queue. Instead,
we then figure out it's disposition based upon a previous command's
association with a signifying event.
If SA_FLAG_EOM_PENDING is set, we don't set an error. We just complete
the command with residual set to the request count (not data moved,
but no error). We continue on.
If SA_FLAG_EOF_PENDING- if we have this, it's only because we're in
Fixed Block mode- in which case we traverse all waiting buffers (which
we can get in fixed block mode because physio has split things up) and
mark them all as no error, but no data moved and complete them.
If SA_FLAG_EIO_PENDING, just mark the buffer with an EIO error
and complete it.
Then we clear all of the pending state bits- we're done.
MFC after: 4 weeks
Handle both old and new TARGIOALLOCUNIT/TARGIOFREEUNIT cases- the new
one allows us to specify inquiry data we want to use.
Handle more of the CAM_DIS_DISCONNECT case.
Move TARGCTLIOALLOCUNIT to OTARGCTLIOALLOCUNIT, TARGCTLIOFREEUNIT
to OTARGCTLIOFREEUNIT and redefine old associated structure to be
old_ioc_alloc_unit- deprecation but preservation of binaries.
Add new structure for same- but this one contains a pointer to
user defined INQUIRY data so you can define what the target
device looks like to the outside world.
1. If we get frozen, unfreeze for disable disconnects.
2. Put CAM_DIS_DISCONNECT commands at the head of the work queue
(we have a target still connected and we can't run anything else
until this command completes).
If we had an error sending the last CTIO, unfreeze the queue anyway.
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
This is useful if you want to dynamically move into a Fibre Channel
or Multi-initiator environment that happens to be particularly noisy
and ugly that requires a lot of retries (with shorter I/O timeouts)
for commands destried by LIPs or Bus Resets.
Reviewed by: deafening silence on audit && scsi on the retry counts
MFC after: 2 weeks
