The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
routines and thus assert if one passes in a rate code with the
high bit set.
Since the high bit can indicate either IEEE80211_RATE_BASIC or
IEEE80211_RATE_MCS, it's up to the caller to determine whether
the rate is 11n or not, and either mask out the BASIC bit, or
call a different function.
(Yes, this does mean that net80211 should grow 11n-aware rate2phytype()
and rate2plcp() functions..)
This may need to happen for the other drivers - it's currently only
done (now) for iwn(4) and bwi(4).
PR: kern/181100
This fixes hostap mode for at least ral(4) and run(4), because there is
no sufficient call into drivers which could be used initialize the node
related ratectl variables.
MFC after: 3 days
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
This prevents a kernel fault by dividing with zero because the initial
rate was 0 and didn't be initialized.
Tested by: Warren Block <wblock at wonkity.com>
MFC after: 3 days
changed to RUN because ic->ic_newassoc isn't set anywhere now. In the
previous bwi_newassoc() is used to initialize AMRR rate routines.
Tested by: Warren Block <wblock at wonkity.com>
MFC after: 3 days
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
register 0x52, not ctrl1. This appears to be a mistake in the bcm
reverse engineering page, and has been corrected there. Tracing
through the code, this is more in keeping with the "documented"
register. Sephe thinks it looks interesting and may be worth
fixing. :)
Submitted by: ddkprog at yahoo com
Reviewed by: Sepherosa Ziehau
# Note: The driver doesn't support either these PHY types, so this is
# effectively a nop.
Submitted by: "ddk"
Obtained from: http://paradox.lissyara.su/bwi.diff
believe it was a BCM4319. However, it is the a/b/g variation of the
BCM4318. The chip itself is labelled BCM4318EKFBG, and the board is
BCM94318MKABG.
Paradox's patch includes the type of 802.11 wireless for each card,
but changes all the names (I don't think the latter is quite right).
Import that part of the patch, but keep the current set of BCM names
(with a minor tweak for the 4306 ones). I'll need to verify them via
some other means.
Obtained from: http://paradox.lissyara.su/bwi.diff (partially)
Broadcom BCM43xx chipsets. This driver uses the v3 firmware that
needs to be fetched separately. A port will be committed to create
the bwi firmware module.
The driver matches the following chips: Broadcom BCM4301, BCM4307,
BCM4306, BCM4309, BCM4311, BCM4312, BCM4318, BCM4319
The driver works for 802.11b and 802.11g.
Limitations:
This doesn't support the 802.11a or 802.11n portion of radios.
Some BCM4306 and BCM4309 cards don't work with Channel 1, 2 or 3.
Documenation for this firmware is reverse engineered from
http://bcm.sipsolutions.net/
V4 of the firmware is needed for 11a or 11n support
http://bcm-v4.sipsolutions.net/
Firmware needs to be fetched from a third party, port to be committed
# I've tested this with a BCM4319 mini-pci and a BCM4318 CardBus card, and
# not connected it to the build until the firmware port is committed.
Obtained from: DragonFlyBSD, //depot/projects/vap
Reviewed by: sam@, thompsa@
