worked in the past only because of good fortune. Anyway, use the contig alloc
routine I wrote awhile ago (vm_page_alloc_contig) for the sound code to do
this allocation. Also, specify read+write on the permissions to pmap_enter().
Specifying just read can have unexpected consquences.
Now floppy tape support is *disabled* unless you specifically
request otherwise. Poul wanted it this way, and I guess I'm not going to argue
though it may seem counter-intuitive. We can always change it back, later.
make the sequencer code fully compatible with the aic7870 (ie 294x adaptors).
I've also added to my local mods putting the sequencer into "FASTMODE" clock.
This gives upwards of 2M/sec write preformance improvement in some scenarios.
There haven't been any reports of this causing problems, and I have been
reaping the benifits of it for more than a week now.
This also includes a new version of the pre-generated file <ugh>
Obtained from: John Aycock (aycock@cpsc.ucalgary.ca) and myself
flags & 0x1. Somebody should build a kernel with this and see if
the floppy-tape damaged people can turn it off properly with userconfig.
I can't reproduce the original problem here.
and into ether_input(). It was silly to have bpf want this one way and
ether_input want it another way. Ripped out trailer support from the few
remaining drivers that still had it.
1) make #includes correct
2) fix bugs in address check macros
3) fixed bugs in, and enabled, recopy if heavily fragmented code
4) moved call to bpf tap to be before enqueing packet (probably gratuitous)
5) fixed bug that caused "abnormal interrupt" at boot time/first use
6) added support for reading Zynx address ROM
7) fixed bug that caused broadcasts to not work shortly after booting (only
manifested if not using multicast - e.g. not in FreeBSD 2.0)
8) fixed spelling errors in comments
Submitted by: Matt Thomas
a discussion going on about removing this code from the burden of the
GPL, but it won't happen before Beta, and this code should be tested
before release.
Supports 27/2842 class adaptec cards and is almost capable of supporting
aic7870 based adapters (294X series cards). It does not support Wide
controllers or the second channel on Twin boards although I have work in
progress on getting both channels and running.
I have also added a few performance improvements to this version that give
us approximately a 25% boost over the original driver. These patches have
been submitted to the author.
Obtained from: Linux aic7770 driver (John Aycock - aycock@cpsc.ucalgary.ca)
of the 1.1.5 driver, a recent version of the NetBSD driver, Andres'
transmission start threshold code, and all other relavent changes to the driver
since it was brought into 2.0. The multicast support from NetBSD has not be
folded in yet. I've tested it under high loads for two weeks and it is now
robust enough to be included in the GENERIC kernel.
Reviewed by: gibbs
Submitted by: vega@sophia.inria.fr (Andres Vega Garcia)
cosmetique) because we already have right things there or his changes
are incorrect.
Fix mcd_subchan to return position, inspired by idea from
bugress@s069.infonet.net, but different implementation.
Here is the improved probe for the mse (Bus Mouse) device driver. I
have been running with this under 1.1.5.1 as well as 2.0 without a hitch for
quite a while.
Submitted by: lars
floppies now. I'm not sure why, but things hang when it gets to the
`changing root to fd0c' part. Without your latest commit, everything works
fine. Maybe you can figure out what you broke after ALPHA! :)
errors at a lower ipl. clist starvation problems can cause hundreds of
tty buffer overflows per second and logging them all amplified the
problems. This problem was less serious in 1.1.5.
Avoid a race in the check for starting a new block of output. com_events
was sometimes messed up and siopoll() looped endlessly. This bug was
introduced in 2.0.
Clean up previous 2 commits. Rename sio_registerdev() to sioregisterdev()
to match the (bad) surrounding naming conventions. There should be a
generic_registerdev().
. avoid resetting the FDC every time the last motor is going off;
instead, give it a 60-second period for possible later reactivation.
This prevents us from needing to recalibrate the FDC too often,
but still allows for an ``automagic error recovery', just in case the
controller is absolutely stuck. (Simply wait for 60 seconds, and
try it again.)
. made the floppy head settle time after a seek a constant
that might be overridden by a config option. (Well, actually the
divisor of the settle time). Pepople often reported problems with
their floppies, so i need a simply mechanism that allows them
to play with that value. (I personally cannot find any problem
on *my* drives.)
. implement the FD_DEBUG ioctl command, in case the driver
is compiled with DEBUG turned on.
. removed a bogus parameter from a printf; the remaining warnings
from gcc -Wall seem to be warnings about the %b format gcc cannot
understand
. rearrange Garett's code to fit better in the existing structure
of #define/type/function ordering.
. make everything fit into 79 columns again.
in the far pointers are multiples of 4K (as is normal when the video
BIOS is at seg 0xc000). Disallow mode switching if the pointer is bad.
Use a new pa_to_va() macro for all BIOS and video addresses in syscons.
and all SCSI devices (except that it's not done quite the way I want). New
information added includes:
- A text description of the device
- A ``state''---unknown, unconfigured, idle, or busy
- A generic parent device (with support in the m.i. code)
- An interrupt mask type field (which will hopefully go away) so that
. ``doconfig'' can be written
This requires a new version of the `lsdev' program as well (next commit).
so i hope i've finally removed all the occasions where the driver
got stuck when there's no floppy in the drive.
Also attemmpting to omit the error mesage for ``recalib failed''
for the first time, since people tend to be confused about this.
else has been probed. This feature could go away again, if we can curb the
problem another way.
if_ed.c, syscons.c: Set the above flag. ed# because it needs it, syscons
because it looks stupid to "detect" the display you have already filled up
with text :-)
bt742a.c: Check bt_cmd() return-val during probe, thus failing on adaptec's.
Also silenced various printf's during the probe.
isa.c: Probe devices with the above flag set before the rest. Reduce the
number of "conflict" messages per device to one.
***
Please test the GENERIC-kernel now, if nobody can make it fail, GENERICAH
and GENERICBT has a finite and short life-expectancy...
***
of mb_offset given the right sequence of 1 and 0 byte mbufs. This bug
was discovered by John Hood who also provided this fix - which is a
rewrite of the routine (and is easier to understand than the code I wrote).
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
Fix endless loop in siopoll() for an event on a tty with no tty struct.
Don't generate unwanted interrupts in the serial console driver. These
bugs probably don't matter unless the tty struct is dynamically allocated.
Support polled mode. To use it, leave out the irq and the vector in
the config file. It only causes extra overhead for open polled ports.
The maximum usable speed is approximately 1000 bps for a 16450 and
15000 bps for a 16550.
Other cosmetic changes.
Bug fixed, that caused system hang on first interrupt on some motherboards.
New version of PCI bus configuration code, now supports dynamic interrupt
configuration (using BIOS supplied values).
NCR SCSI and DEC Ethernet driver patched to use this feature.
*** Remove PCI IRQ specifications from your kernel config file ! ***
the first place was so that BPF could grok trailer packets. I've since
decided that this is a job for tcpdump to decipher (if at all). Also
fixed up checks for received packet length to better cope with ancient
starlan boards.
be merged at some point)
New AMD family ethernet driver. Should support BICC,NE2100, TNIC,
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
New version with improved support for WIDE SCSI using the NCR 53c825.
Test for buggy secondary cache implementations.
PCI Int to IRQ mapping now specified per slot.
This is needed for having the fdformat program no longer searching
non-public include paths.
Protect the definitions in fdreg.h against double inclusion.
more work required to grab all fonts
2)Make standard VGA font as default, make HARDFONTS an option
(load iso8859 fonts instead)
3)Check fonts_loaded for all restore (copy_font...palette)
sequences.
when the drive had been left on a cylinder > 67 after kernel boot. The
most common case for this is booting a kernel that is located on
the inner cylinders of a floppy.
Also removed all occurences of spinwait(), replaced by DELAY.
Nuked a return line saying nothing, this might make Bruce happy 8^)
Submitted by: partially by Bruce Evans
date: 1994/05/22 12:35:38; author: joerg; state: Exp; lines: +6 -6
First round of floppy changes. Try making `fd' more robust.
New features:
. ioctl command for setting the drive type (density etc.); restricted
to the super-user
. ioctl for getting/seting `drive options'; currently only option
is FDOPT_NORETRY: inhibit the usual retries; used when verifying
a newly formatted track
Fixes:
. function prototypes
. made all internal functions `static'
. cleaned up & corrected .h files
. restructured, to make the chaotic function sequence more rational
. compiled with -Wall, and cleared all warnings
. introduced a mirror for the (write-only) `digital output register',
to avoid the current kludge
. device probing completed by seeking/recalibrating, and looking
for track 0 being found
. holding the controller down in reset state while it is idle (and
thus saving allot of headaches)
. make requests fail that are not a multiple of the (physical)
sector size
. removed the fixed physical sector size (512 bytes), allowing for any
size the controller could handle (128/256/512/1024 bytes)
. replaced some silly messages
. fixed the TRACE* macro usage, debugging reports should be complete
now again (debugging output is HUGE! though)
. removed fd_timeout for SEEK command; seeks are always reported by
the controller to succeed, since the `success' only refers to the
controller's idea of success - there is no hardware line to tell about
the seek end (other than the `track 0' line)
. catch SENSEI's that report about a `terminated due to READY changed'
status - could happen after a controller reset
. converted ``hz / <something>'' divide operations to divisors that are
powers of two, so gcc can optimize them into shifts
. write/format operations are checked against a write-protected medium
now *prior* starting the operation
. error reports of `invalid command' and `wrong cylinder' will cause
shortcuts in the retrier() now
. fixed a bug in the retrier() causing bogus block numbers to be reported
. fdformat() does care for errors now
Known Bugs:
. no attempts have been made (yet) to improve the performance
. sometimes, bogus ``seek/recalib failed'' messages are logged; this
is still a bug in the driver, but it's not harmful since it's
usually caught by the retrier()
Reviewed by:
Submitted by:
Obtained from:
320x200 256col VGA. This is nessesary for the iBCS stuff to work right.
(And we get the benefit of more video modes). Uses the videocard BIOS
to optain mode tables.
Added a "green" saver, switches off the syncs for "green" monitors.
Reviewed by:
Submitted by:
Obtained from:
wider variety of systems. Include the deivers from pci_intel.c in
pci_config.c (I hope this is what was intended; my system works ok).
Use pmap_mapdev(). Automatically map any large linear frame buffers
or whatnot in VGA-style devices which ordinarily would not have their
own drivers, and don't call not_supported() for them. (This shuts up
complaints about my Matrox card.) Include the beginnings of what could
eventually become dynamically-loadable PCI devices. Allow for the
possibility of PCI devices simply providing a PCI veneer over an existing
ISA device, and shut up about them, too.
Make autoconfiguration text conform more to the style of other supported
buses.
you download the microcode to the DSP everytime you power on your system.
They provide a dos-program to do so, but no other support. This commit adds
code to the sio-driver, which implement an ioctl, which will down-load the
micro-code.
To get this functionality, you must define DSI_SOFT_MODEM.
The program to actually employ the ioctl is not included, but the entire
source looks like this:
#include <sys/ioctl.h>
#include <stdio.h>
main()
{
unsigned char buffer[100000];
int i;
read(0,buffer,100000);
if((i = ioctl(1,TIOCDSIMICROCODE,buffer)) < 0)
perror("ioctl");
return i;
}
And you use it like this:
smload < data144b.dsi > /dev/ttyid3
You need to copy the *.DSI files from the dos-media provide with your modem.
You can see what is downloaded by issuing the ATI3 command to the modem.
DSI's scheme for what code you can run on your modem isn't violated by this.
Poul-Henning Kamp
phk@freefall.cdrom.com
Add initialization to the if_ie driver for the Micom Interlan NI5210 card.
This is a very old 82586 based card with only 8Kb or 16Kb on board memory.
Also only 8-bit wide instead of 16-bit like the AT& or 3COM card.
Warning: this thing is only tested so far that it detects all bits
correctly but is not yet on an ethernet. Will do that tomorrow.
Submitted by:
Update the if_ep driver for the 3C579 and bring over some of the
changes from the netbsd driver.
This is not complete: the detection of the irq in the eisa does not
work and sometimes the reset for the 3C509 in ISA in an EISA bus system
don't work ( Need a hard reset to be found again == reset knob).
DIOCGDINFO, DIOCGPART, DIOCWDINFO, DIOCSDINFO, CDIOCPLAYMSF, CDIOCRESET,
CDIOCEJECT.
CDIOCPLAYBLOCKS removed (old implementation completely wrong and I don't
know how to implement it correctly).
All routines now detects media change correctly.
DELAY_GETREPLAY increased for long time access from first track
to last.
mcd_waitrdy() now use MIN_DELAY=15 as minimal delay which independs
of machine speed.
mcd_doread() now uses real status (old code uses obsoleted soft copy of it).
clear XBSY on error in mcd_doread()
mcd_statrt(): add missing splx(s), cause dead hang with unmatched slpbio()
optimize mcd_doread(), don't set CD mode each time, keep soft copy of mode.
call getdisklabel() _after_ mcdsize() for proper sizes
mcdopen(): old code forget to set MCDREADRAW in flags when open RAW
partition, doread check it for setting RAW CD mode.
Do nothing on stray interrupt (which sometimes occurse, because driver
read data block too slow, DOS driver use 'insb' here). Old stray code
cause timeouts.
Read toc entries code rewritten to return many requested entries
(as supposed) instead of one entry with incorrect structure.
CMDREAD2 requests covered with disable_intr()/enable_intr()
(from DOS driver)
Read junk code added after read block code in doread (from DOS driver)
mcd_read_toc() code fixed to read all needed entries, old code cause
some audio tracks is not played.
mcd_playtracks() code fixed to proper check valid track range.
New binary read modes implemented (from DOS driver).
Submitted by:
Put the printf("can't map 3c507 ram.. into an ifdef DEBUG. This will
confuse only normal users and the ie0 found/not found is sufficient.
Submitted by:
1) if_ie.c:
Changed a printf and put a space in it. Formerly the "<3C507>"
confused the syslog. He tried to see that as the priority to
log that message.
2) isa_device.h:
Changed the iobase variable from short to u_short. EISA
Adresses can go up to 0xf000 and the sign extension doesn't
look good in the probe output. Example:
ep1 at 0xffff8000-0xffff8000f is not good :-), i like more a
ep1 at 0x8000-0x8000f.
3) isa.c:
Changed a string constant from "probe" to "prob", it gets
later already an "ed" tagged on the end.
in your kernel config now).
2) Added ps ddb function from 1.1.5. Cleaned it up a bit and moved into its
own file.
3) Added \r handing in db_printf.
4) Added missing memory usage stats to statclock().
5) Added dummy function to pseudo_set so it will be emitted if there
are no other pseudo declarations.
2) DELAY(1) does nothing, it affects audio playing f.e:
driver can't play second half of disk, changed to DELAY(10)
3) Debugging messages #ifdef DEBUGed
find something useful to do other than taking credit for other people's
work. Also make the 3C507 bits match the indentation style of the rest of
the code.
Merged changes from 2.0 version (revisions 1.46-1.50) by hand.
Finished conversion to clists: removed flush of tty output buffer
in comflush() (most writes were truncated to 256 bytes) and restored
bypass of ttyinput() in siopoll().
Finished conversion to 2.0 types - more void *'s, less caddr_t's,
less casts, no Dev_t's.
Only these things are seriously broken now compared with 1.1.5:
waiting for output complete is impossible so ttywait() can deadlock;
sioclose() isn't called enough so sioopen() sometimes returns EBUSY
unnecessarily; input flow control is not implemented.
Submitted by:
Add the 3com 3C507 card to the if_ie.c driver. The files elink.c and
elink.h are helding routines that are shared between the 3C507 and the
3C509/3C579. if_ie507.h are constant declarations unique to the 3C507.
The code is based on the NetBSD driver if_ie.c donated to NetBSD by
Rafal Boni and then modified by Charles Hannum.
Added a missing #ifdef INET wrapper in lpt.c
Main change:
Removed the timeout_func_t casts from timeout calls and
correctly defined the timeout routines to conform to
the new format.
lpt.c doesn't have this change.
Reviewed by:
Submitted by:
use of timeout_t -> timeout_func_t in aha1542 and aha1742 drivers.
2) fix a bug in the portalfs that was uncovered by better prototyping -
specifically, the time must be converted from timeval to timespec
before storing in va_atime.
3) fixed/added some miscellaneous prototypes
- Delete redundant declarations.
- Add -Wredundant-declarations to Makefile.i386 so they don't come back.
- Delete sloppy COMMON-style declarations of uninitialized data in
header files.
- Add a few prototypes.
- Clean up warnings resulting from the above.
NB: ioconf.c will still generate a redundant-declaration warning, which
is unavoidable unless somebody volunteers to make `config' smarter.
/usr/src/sys/i386/isa/clock.c:
o Garrett's statclock changes.
o Wire xxxintr, not Vclk.
o Wire using register_intr(), not setidt().
/usr/src/sys/i386/isa/icu.s:
o Garrett's statclock changes.
o Removed unused variable high_imask.
o Fake int 8 for rtc as well as int 0 for clk. Required for kernel
profiling with statclock, harmless otherwise.
/usr/src/sys/i386/isa/isa.c:
o Allow isdp->id_irq and other things in *isdp to be changed by
probes. Changing interrupts later requires direct calls to
register_intr() and unregister_intr() and more care.
ALLOW_CONFLICT_* is brought over from 1.1.5, except
ALLOW_CONFLICT_IRQ is not supported. IRQ conflict checking is
delayed until after probing so that drivers can change the IRQ
to a free one; real conflicts require more cooperation between
drivers to handle.
o Too many details to list.
o This file requires splitting and a lot more work.
/usr/src/sys/i386/isa/isa_device.h:
o Declare more things more completely.
/usr/src/sys/i386/isa/sio.c:
o Prepare to register interrupt handlers as fast.
/usr/src/sys/i386/isa/vector.s:
o Generate entry code for 16 fast interrupt handlers and 16 normal
interrupt handlers. Changed some constants to variables:
# $unit is now intr_unit[intr]. Type is int. Someday it should
be a cookie suitable for the handler (e.g., a struct com_s for
sio).
# $handler is now intr_handler[intr].
# intrcnt_actv[id_num] is now *intr_countp[intr]. The indirection
is required to get a contiguous range of counters for vmstat
and so that the drivers depend more in the driver than on the
interrupt number (drivers could take turns using an interrupt
and the counts would remain correct). There is a separate
counter for each device and for each stray interrupt. In
1.1.5, stray interrupt 7 clobbers the count for device 7 or
something worse if there is no device 7 :-(.
# mask is now intr_mask[intr] (was already indirect).
o Entry points are now _XintrI and _XfastintrI (I = intr = 0-15),
not _VdevU (U = unit).
o Removed BUILD_VECTORS stuff. There's a trace of it left for
the string table for vmstat but config now generates the
string in one piece because nothing more is required.
o Removed old handling of stray interrupts and older comments
about it.
Submitted by: Bruce Evans
``changes'' are actually not changes at all, but CVS sometimes has trouble
telling the difference.
This also includes support for second-directory compiles. This is not
quite complete yet, as `config' doesn't yet do the right thing. You can
still make it work trivially, however, by doing the following:
rm /sys/compile
mkdir /usr/obj/sys/compile
ln -s M-. /sys/compile
cd /sys/i386/conf
config MYKERNEL
cd ../../compile/MYKERNEL
ln -s /sys @
rm machine
ln -s @/i386/include machine
make depend
make
change all of these to be timeout_funt_t and remove the casts and
typedef?
Remove secound argument (uban) from ifp->if_reset routines since it is now
obsolete.
Reviewed by: David Greenman
1) check va before clearing the page clean flag. Not doing so was
causing the vnode pager error 5 messages when paging from
NFS. (pmap.c)
2) put back interrupt protection in idle_loop. Bruce didn't think
it was necessary, John insists that it is (and I agree). (swtch.s)
3) various improvements to the clustering code (vm_machdep.c). It's
now enabled/used by default.
4) bad disk blocks are now handled properly when doing clustered IOs.
(wd.c, vm_machdep.c)
5) bogus bad block handling fixed in wd.c.
6) algorithm improvements to the pageout/pagescan daemons. It's amazing
how well 4MB machines work now.
