by the subsequent mix_setdevs() and friends.
- Minor style(9) declaration arrangement nit.
Requested by: joeld
Submitted by: pluknet <pluknet@gmail.com>
- Double the number of descriptors that a single call to send can use
- Quadruple the number of descriptors that can be reclaimed per pass
- only run reclaim twice per second
- increase coalesce timer from 3.5us to 5us
fix printf warning on 64-bit platforms
Neither me nor Ariff have access to any of this hardware, so all tests
have been made by Konstantin and Artem. Commit message mostly written
by Konstantin.
envy24:
- Add test code to support rear line-in input on 'Terratec DMX 6fire'
audio card. This code is also intended to be used in the future for
support of cards, that have I2C-to-GPIO expanders wired between the
control line of the audio codec and the Envy24, however such cards
are too complex and i can't add that support without hardware sample
of such board, i've already tried and failed.
envy24ht:
- Add support for 'AudioTrak Prodigy HD2'.
- Add support for 'AudioTrak Prodigy 7.1 XT'.
- Add support for 'ESI Juli@' (Works ok, DAC volume is hard-coded for
the time being, so 'mixer vol ...' doesn't work, only 'mixer pcm
...' works). [1]
- Fix bug in the init data for M-Audio Revolution 5.1, that
results in distorted sound.
- Add software volume control (now 'mixer pcm' works, thanks to Ariff).
- Add support for more samples rates - 176.4kHz and 192kHz.
- Fix problem with the 192kHz samples rate playback when 24.576MHz
crystal is used on the board instead of 49.152MHz crystal.
spicds:
- Add support for Asahi Kasei flagship DAC - AK4396 (used in AudioTrak
Prodigy HD2).
Submitted by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Tested by: Artem Antonov [1]
Reviewed by: ariff
the card, panic explicitly if EN_DEBUG is enabled. In the (default)
case of !EN_DEBUG, the driver resets the card. Probably this case
shouldn't exist at all.
SD Simplified specification, as well as other SD and SDIO
implemenations I've examined, suggest this disclaimer may be required.
It is unclear to me exactly what the license would be for, or why it
might be required. Err on the side of caution and include this
disclaimer so anybody deploying this code can judge for themselves. I
have no further unformation about the details.
clusters. This helps quite a bit on my low end machines (improves
performance by about 300Kpps when being blasted by a hardware
packet generator).
- Include one extended f/w counter forgotten in earlier commit
Sponsored by: Myricom Inc.
- upgrade to reflect state of 1.0.0.86
- move from firmware rev 3.2 to 4.0.0
- import driver bits for offload functionality
- remove binary distribution clause from top level files as it
runs counter to the intent of purely supporting the hardware
MFC after: 3 days
back in a simulated resume instead of entering the requested suspend state.
This helps in testing drivers separately from the acpi suspend code. To
test your drivers, set debug.acpi.suspend_bounce=1 and then run
acpiconf -s3 (or 4).
MFC after: 1 day
device's, not the bridge's, softc to be used to check the
PCIB_DISABLE_MSI flag. This resulted in randomly allowing
or denying MSI interrupts based on whatever value the driver
happened to store at sizeof(device_t) bytes into its softc.
I noticed this when I stopped getting MSI interrupts
after slighly re-arranging mxge's softc yesterday.
- Remove code to use the special wc_fifo. It has been disabled by default
in our other drivers as it actually slows down transmit by a small amount
- Dynamically determine the amount of space required for the rx_done
ring rather than hardcoding it.
- Compute the number of tx descriptors we are willing to transmit per
frame as the minimum of 128 or 1/4 the tx ring size.
- Fix a typo in the tx dma tag setup which could lead to unnecessary
defragging of TSO packets (and potentially even dropping TSO packets
due to EFBIG being returned).
- Add a counter to keep track of how many times we've needed to
defragment a frame. It should always be zero.
- Export new extended f/w counters via sysctl
Sponsored by: Myricom, Inc.
- Update to the latest (1.4.18) f/w. This f/w introduces a new
receive mode which allows us to use FreeBSD's physically discontinuous
MJUM9BYTES clusters.
- Switch the driver from chaining MJUMPAGESIZE clusters to using
MJUM9BYTES clusters to avoid mbuf chaining overheads. Due to this
change, people running obsolete f/w images will be limited to an MTU of
PAGE_SIZE - 16.
- Add (disabled by default) support for Large Receive Offload.
Sponsored by: Myricom, Inc.
adapter list still capable, but only PCI-E adapters are now enabled.
The user can enable older PCI-X or PCI adapters using ifconfig.
Secondly, Arthur Hartwig pointed out my MSI change was not working
correctly, changed to something that now does. Thanks Arthur.
There was also a fundamental bug in the 82575 MSIX code, the MSIX
registers had to be mapped, opps :)
Rubber-stamped by: Pdeuskar
