ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
we have the rc4 code already in the kernel (via wlan stuff or awi).
Add a dependency on the rc4 module so if it doesn't exist then load it.
Reviewed by: archie
These makefiles work when building in the sys/modules directory, but
not with the objdir stuff that buildkernel uses. This is because they
used -I../../../blah rather than -I${.CURDIR}/../../../blah.
# I didn't fix the abuse of CFLAGS to specify -g since I wanted the
# barest minimal change since we're in a code freeze.
Approved by: make buildkernel...
Hat for armchair anarchists: core member fixing src tree damage
Has been seen to work on several cards and communicating with
several mobile phones to use them as modems etc.
We are still talking with 3com to try get them to allow us to include
the firmware for their pccard in the driver but the driver is here..
In the mean time
it can be downloaded from the 3com website and loaded using the utility
bt3cfw(8) (supplied) (instructions in the man page)
Not yet linked to the build
Submitted by: Maksim Yevmenkin <myevmenk@exodus.net>
Approved by: re
This is NOT YET CONVERTED TO -current.
This node is a source for preprogrammed packets at a known rate for testing.
I will convert it to -current "in place" but will MFC teh original
pre-conversion variant as that is what is originally submitted.
Man page my me, info from Dave's README.
Submitted by: Dave Chapeskie <dchapeskie@SANDVINE.com>
Obtained from: Sandvine inc.
MFC after: 1 week
These are really only partly netgraph nodes as they do not use the
netgraph interfaces for many of the functions for which they could
be used, however they represent important functionality.
Submitted by: wpaul
MFC after: 2 days
so that /dev/mumble can be the entrypoint to some networking graph,
e.g. a tunnel or a remote tape drive or whatever...
Not fully tested (by me) yet.
Submitted by: Mark Santcroos <marks@ripe.net>
MFC after: 3 weeks
hooks depending on ethertype. Great for prototyping protocols.
connects to the lower and upper hooks of an ethernet type of node.
Obtained from: Monzoon Networks.
Thanks to Andre Oppermann, May 2001.
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
This helps to stop it from geting out of sync.
It is not part of the normal build but I can use it with all the others
when I make changes to netgraph to ensure it is buildable.
packet flow into two unidirectional flows.
Part of a suite of nodes developed for packet flow control.
More to follow as I have time to port them to 5.x or
as others do so. The ipfw node will be the hardest..
Submitted by: "Vitaly V. Belekhov" <vitaly@riss-telecom.ru>
- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
