- Make sure timer0_max_count is set to a correct value in the lapic case.
- Revert i8254_restore() to explicitly reprogram timer 0 rather than
calling set_timer_freq() to do it. set_timer_freq() only reprograms
the counter if the max count changes which it never does on resume. This
unbreaks suspend/resume for several people.
Tested by: marks, others
Reviewed by: bde
MFC after: 3 days
copied and pasted. I had actually tested without this change in my
trees as had the other testers.
Reported by: bde, Rostislav Krasny rosti dot bsd at gmail dot com
Approved by: re (scottl)
Pointy hat to: jhb
as they are already default for I686_CPU for almost 3 years, and
CPU_DISABLE_SSE always disables it. On the other hand, CPU_ENABLE_SSE
does not work for I486_CPU and I586_CPU.
This commit has:
- Removed the option from conf/options.*
- Removed the option and comments from MD NOTES files
- Simplified the CPU_ENABLE_SSE ifdef's so they don't
deal with CPU_ENABLE_SSE from kernel configuration. (*)
For most users, this commit should be largely no-op. If you used to
place CPU_ENABLE_SSE into your kernel configuration for some reason,
it is time to remove it.
(*) The ifdef's of CPU_ENABLE_SSE are not removed at this point, since
we need to change it to !defined(CPU_DISABLE_SSE) && defined(I686_CPU),
not just !defined(CPU_DISABLE_SSE), if we really want to do so.
Discussed on: -arch
Approved by: re (scottl)
timer since irq0 isn't being driven at hz in that case and we don't need to
try to handle edge cases with rollover, etc. that require irq0 to be firing
for the timecounter to actually work.
Submitted by: phk
Tested by: schweikh
Approved by: re (scottl)
files after they were repo-copied to sys/dev/atkbdc. The sources of
atkbdc(4) and its children were moved to the new location in preparation
for adding an EBus front-end to atkbdc(4) for use on sparc64; i.e. in
order to not further scatter them over the whole tree which would have
been the result of adding atkbdc_ebus.c in e.g. sys/sparc64/ebus. Another
reason for the repo-copies was that some of the sources were misfiled,
e.g. sys/isa/atkbd_isa.c wasn't ISA-specific at all but for hanging
atkbd(4) off of atkbdc(4) and was renamed to atkbd_atkbdc.c accordingly.
Most of sys/isa/psm.c, i.e. expect for its PSMC PNP part, also isn't
ISA-specific.
- Separate the parts of atkbdc_isa.c which aren't actually ISA-specific
but are shareable between different atkbdc(4) bus front-ends into
atkbdc_subr.c (repo-copied from atkbdc_isa.c). While here use
bus_generic_rl_alloc_resource() and bus_generic_rl_release_resource()
respectively in atkbdc_isa.c instead of rolling own versions.
- Add sparc64 MD bits to atkbdc(4) and atkbd(4) and an EBus front-end for
atkbdc(4). PS/2 controllers and input devices are used on a couple of
Sun OEM boards and occur on either the EBus or the ISA bus. Depending on
the board it's either the only on-board mean to connect a keyboard and
mouse or an alternative to either RS232 or USB devices.
- Wrap the PSMC PNP part of psm.c in #ifdef DEV_ISA so it can be compiled
without isa(4) (e.g. for EBus-only machines). This ISA-specific part
isn't separated into its own source file, yet, as it requires more work
than was feasible for 6.0 in order to do it in a clean way. Actually
philip@ is working on a rewrite of psm(4) so a more comprehensive
clean-up and separation of hardware dependent and independent parts is
expected to happen after 6.0.
Tested on: i386, sparc64 (AX1105, AXe and AXi boards)
Reviewed by: philip
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
of MCOUNT to have a C version and an asm version with the same name and
not have LOCORE ifdefs to distinguish them. <machine/profile.h> provides
a C version and <machine/asmacros.h> provides an assembler version.
Discussed with: bde
i8253reg.h, and add some defines to control a speaker.
- Move PPI related defines from i386/isa/spkr.c into ppireg.h and use them.
- Move IO_{PPI,TIMER} defines into ppireg.h and timerreg.h respectively.
- Use isa/isareg.h rather than <arch>/isa/isa.h.
Tested on: i386, pc98
- Move MD files into <arch>/<arch>.
- Move bus dependent files into <arch>/<bus>.
Rename some files to more suitable names.
Repo-copied by: peter
Discussed with: imp
Instead, explicitly enable them when we setup the interrupt handler.
Also, move the setting of stathz and profhz down to the same place so
that the code flow is simpler and easier to follow.
- Don't setup an interrupt handler for IRQ0 if we are using the lapic timer
as it doesn't do anything productive in that case.
o Use IP_NPX in preference to hard coded value to write 0 to clear busy#
o Use md macro for a full reset of the npx
o Use IRQ_NPX in preference to hard coded value for each platform.
# The other two ifdefs in this file are hard to remove
rman_resource_resournce_bound wrt end parameter. The end parameter
here was the same as the start. However, it should be start + count -
1, so make it that instead.
place.
This moves the dependency on GCC's and other compiler's features into
the central sys/cdefs.h file, while the individual source files can
then refer to #ifdef __COMPILER_FEATURE_FOO where they by now used to
refer to #if __GNUC__ > 3.1415 && __BARC__ <= 42.
By now, GCC and ICC (the Intel compiler) have been actively tested on
IA32 platforms by netchild. Extension to other compilers is supposed
to be possible, of course.
Submitted by: netchild
Reviewed by: various developers on arch@, some time ago
Also save the DAC state, increase the maximum save state size from
4k to 8k, and refuse to save the VESA state if the BIOS reports it
is larger than the maximum size we can handle.
It doesn't appear that anything currently uses this code, but it
turns out to be capable of restoring some notebook displays to a
working state after a suspend-resume cycle.
rather than forwarding interrupts from the clock devices around using IPIs:
- Add an IDT vector that pushes a clock frame and calls
lapic_handle_timer().
- Add functions to program the local APIC timer including setting the
divisor, and setting up the timer to either down a periodic countdown
or one-shot countdown.
- Add a lapic_setup_clock() function that the BSP calls from
cpu_init_clocks() to setup the local APIC timer if it is going to be
used. The setup uses a one-shot countdown to calibrate the timer. We
then program the timer on each CPU to fire at a frequency of hz * 3.
stathz is defined as freq / 23 (hz * 3 / 23), and profhz is defined as
freq / 2 (hz * 3 / 2). This gives the clocks relatively prime divisors
while keeping a low LCM for the frequency of the clock interrupts.
Thanks to Peter Jeremy for suggesting this approach.
- Remove the hardclock and statclock forwarding code including the two
associated IPIs. The bitmap IPI handler has now effectively degenerated
to just IPI_AST.
- When the local APIC timer is used we don't turn the RTC on at all, but
we still enable interrupts on the ISA timer 0 (i8254) for timecounting
purposes.
uses the i8237 without trying to emulate the PC architecture move
the register definitions for the i8237 chip into the central include
file for the chip, except for the PC98 case which is magic.
Add new isa_dmatc() function which tells us as cheaply as possible
if the terminal count has been reached for a given channel.
interrupts, read from the interrupt status register to clear any pending
interrupts. Otherwise in some rare cases the RTC would never fire any
interrupts as it constantly thinks it has an interrupt pending.
PR: i386/17800
PR: kern/76776
Submitted by: Jose M. Alcaide jose at we dot lc dot ehu dot es
MFC after: 2 weeks
instead of burying that in the atpic(4) code as atpic(4) is not the only
user of elcr(4). Change the elcr(4) code to export a global elcr_found
variable that other code can check to see if a valid ELCR was found.
MFC after: 1 month
the ISA and CBUS (called isa on pc98) attachments. Eliminate all PC98
ifdefs in the process (the driver in pc98/pc98/mse.c was a copy of the one
in i386/isa/mse.c with PC98 ifdefs). Create a module for this driver.
I've tested this my PC-9821RaS40 with moused. I've not tested this on i386
because I have no InPort cards, or similar such things. NEC standardized
on bus mice very early, long before ps/2 mice ports apeared, so all PC-98
machines supported by FreeBSD/pc98 have bus mice, I believe.
Reviewed by: nyan-san
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
and which takes a M_WAITOK/M_NOWAIT flag argument.
Add compatibility isa_dmainit() macro which whines loudly if
isa_dma_init() fails.
Problem uncovered by: tegge
pic_eoi_source() into one call. This halves the number of spinlock operations
and indirect function calls in the normal case of handling a normal (ithread)
interrupt. Optimize the atpic and ioapic drivers to use inlines where
appropriate in supporting the intr_execute_handlers() change.
This knocks 900ns, or roughly 1350 cycles, off of the time spent servicing an
interrupt in the common case on my 1.5GHz P4 uniprocessor system. SMP systems
likely won't see as much of a gain due to the ioapic being more efficient than
the atpic. I'll investigate porting this to amd64 soon.
Reviewed by: jhb
future:
rename ttyopen() -> tty_open() and ttyclose() -> tty_close().
We need the ttyopen() and ttyclose() for the new generic cdevsw
functions for tty devices in order to have consistent naming.
