chip revision often found in the blades and resulting in interfaces
not sensing carrier signal. Looking at all problem reports it
appears that it only affects some very specific silicon revision
(ASIC (0x57081021); Rev (B2)) and version of the PHY that
supports 1000baseSX-FDX media only. Therefore, narrow the scope of
workaround to combination of that revision and media type. Given
that the first report on this issue is dated back to 2007, there is
not much hope that this issue will ever be properly resolved.
Among affected systems are IBM HS21, Intel SBXD132 and HP BL460c.
PR: 118238, 122551, 140970
MFC after: 1 month
88E1149 PHY. This will fix intermittent watchdog timeouts as well
as very slow network performance on 88E8072 Yukon Extreme.
PR: kern/144148
MFC after: 1 week
copper and fiber interfaces over GMII so an explicit check is
necessary to know whether it was configured for fiber interface.
This change make BCM5715S work.
Tested by: olli
MFC after: 1 week
Unlike most other PHYs there is no easy way to know which media
type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now
passed via bus-specific instance variable of a device. While I'm
here add 88E1112 specific work around to set SIGDET polarity low.
Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly
gave remote access to system with DGE-560SX.
value instead of blindly resetting it to 0. However, it seems page
select bits of some 88E1116 PHY is initialized to invalid one such
that restoring page select bits after programming broke MII
register access. The correct solution would be reset page select
bits to 0 in PHY attach stage but it would require more testing.
Since we're in BETA stage such a change would be dangerous so just
back it out.
This change should fix nfe(4) breakage on NVIDIA MCP55.
Reported by: Ryan Rogers < webmaster <> doghouserepair dot com >
Sam Fourman Jr. < sfourman <> gmail dot com >
Tested by: Ryan Rogers < webmaster <> doghouserepair dot com >
Sam Fourman Jr. < sfourman <> gmail dot com >
Approved by: re (kib)
of the DP83861 and DP83891.
- Reset the PHY during attach so it's in a known state.
- Add a comment describing why we hardwire 10baseT support in
the BMSR.
- Always explicitly set IFM_HDX for half-duplex. [1]
Obtained from: OpenBSD [1]
MFC after: 2 weeks
FE+ controller. Due to the severe silicon bugs for Yukon FE+,
88E3016 seems to require more workarounds. However I'm not sure
whether the workaround is PHY specific or only applicable to Yukon
FE+. The datasheet for the PHY is publicly available but it lacks
several details for the workaround used in this change. The
workaround information was obtained from Linux. Many thanks to
Yukon FE+ users who helped me add 88E3016 support.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
advertisement register. Some PHYs such as 88E3016 requires NEXT
Page capability to establish valid link. Also set protocol selector
field which is read only but it makes the intention clearer.
is valid only for auto-negotiation case so check the bit if we know
auto-negotiation is active. While I'm here explicitly checks
current speed with speed mask and set IFM_NONE if resolved speed
is unknown.
checks extended status register to see whether the PHY is fast
ethernet or not. This removes a lot of checks for specific PHY
models and it makes easy to add more PHYs to e1000phy(4).
While I'm here remove setting mii_anegticks as it is set with
mii_phy_add_media().
get default next page configuration. While I'm here explicitly set
IP1000PHY_ANAR_CSMA bit. This bit is read-only and always set
by hardware so setting it has no effect but it would clear the
intention. With this change controllers that couldn't establish
1000baseT link should work.
PR: kern/130846
bank instead of copper/fiber bank which in turn resulted in
wrong registers were accessed during PHY operation. It is
believed that page 0 should be used for copper PHY so reinitialize
E1000_EADR to select default copper PHY.
This fixes link establishment issue of nfe(4) on Sun Fire X4140.
OpenBSD also has similimar patch but they just reset the E1000_EADR
register to page 0. However some Marvell PHYs((88E3082, 88E1000)
don't have the extended address register and the meaning of the
register is quite different for each PHY model. So selecting copper
PHY is limited to 88E1149 PHY which seems to be the only one that
exhibits link establishment problem. If parent device know the type
of PHY(either copper or fiber) that information should be notified
to PHY driver but there is no good way to pass this information yet.
Reported by: thompsa
Reviewed by: thompsa
only mode and restore original value of extended address register
instead of overwriting it with page 1. There are still instance
information passing issue(e.g configured media type: fiber or
copper) from driver to PHY layer but this change make the selected
PHY work with 88E1112 PHY.
Reported by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
Tested by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
When there's an error, we don't want to free the children, since it
will be stack garbage. While we did fail to dereference it by setting
devs to 0, we didn't fail to call free. We never failed to fail, it
was the easiest thing to do.
Also report current link state while auto-negotiation is in
progress.
With this change link loss should be reported within a second
and drivers that rely on link state should work.
Reported by: Pete French < petefrench at ticketswitch dot com >
Tested by: Pete French < petefrench at ticketswitch dot com >
MFC after: 1 week
