and fixed everything that depended on getting it from the wrong
place. Most of the broken things actually only depended on getting
the declaration of their interrupt handler from "ioconf.h".
supports All Cyrix CPUs, IBM Blue Lightning CPU and NexGen (now AMD)
Nx586 CPU, and initialize special registers of Cyrix CPU and msr of
IBM Blue Lightning CPU.
If revision of Cyrix 6x86 CPU < 2.7, CPU cache is enabled in
write-through mode. This can be disabled by kernel configuration
options.
Reviewed by: Bruce Evans <bde@freebsd.org> and
Jordan K. Hubbard <jkh@freebsd.org>
form `tv = time'. Use a new function gettime(). The current version
just forces atomicicity without fixing precision or efficiency bugs.
Simplified some related valid accesses by using the central function.
can't perform overlapping commands on both of its channels.
To enable the CMD640B work-around, the kernel must be compiled with
"options CMD640". Without that option there should be no difference
in the code produced compared to the previous revision of wd.c.
Submitted by: Wolfgang Helbig <helbig@ba-stuttgart.de>
effect immediately, but required a following (normally redundant) G0
into GL mapping. This adds one layer of indirection (thus might make it
slower), but fixes the broken box character drawing in pcvt.
Hellmuth and Bruce are unfortunately too busy too review this right now,
but i wanna have it in 2.2 since it has often been asked in the past.
Warning: this won't work yet with PCVT_SCANSET=2 along in early
console mode (boot -c, or boot -d).
A big thanks to Kazutaka, and a word of apologies for delaying the
review for that long time...
Submitted by: yokota@zodiac.mech.utsunomiya-u.ac.jp (Kazutaka YOKOTA)
valid signals, else return EINVAL for ioctl VT_SETMODE.
this fixes a problem that anybody with vty access can panic the system.
2.2-Candidate (and 2.1.0 I believe)
Reviewed-by: sos
available in buffer when buffer was completely empty.
It now correctly reports the total buffer space available.
Reviewed by: jkh, davidg
Obtained from: Linux 1.3.20's sound driver code
changes, so don't expect to be able to run the kernel as-is (very well)
without the appropriate Lite/2 userland changes.
The system boots and can mount UFS filesystems.
Untested: ext2fs, msdosfs, NFS
Known problems: Incorrect Berkeley ID strings in some files.
Mount_std mounts will not work until the getfsent
library routine is changed.
Reviewed by: various people
Submitted by: Jeffery Hsu <hsu@freebsd.org>
The PS/2 mouse device responds to a reset command with a sequence of
ACK(fa), RESULT(aa) and ID(00). Most PS/2 mice immediately returns
ACK, but spend sometime before sending RESULT. The Armada takes time
before ACK; extra delay is necessary before the call to read ACK.
The problem was reported in comp.unix.bsd.freebsd.misc and the patch
was tested by the reporter. No PR was filed, by the way.
with <= 100 usec between each character arrival time. This didn't happen
until rev.1.75 of clock.c because DELAY(100) used to delay for closer to
80 usec than 100 usec, and the minimum time between character arrivals is
87.8 usec at the maximum supported speed of 115200 bps 8N1.
Clear DCD timestamp flag on close (the input timestamp flag is already
cleared).
key "print scrn".
It used to stop at the first non-open vty, now it skips the non-open
ones and thereby enable one to cycle around all open vty by pressing
"print scrn".
I have code to calibrate the overhead fairly accurately, but there
is little point in using it since it is most accurate on machines
where an estimate of 0 works well. On slow machines, the accuracy
of DELAY() has a large variance since it is limited by the resolution
of getit() even if the initial delay is calibrated perfectly.
Use fixed point and long longs to speed up scaling in DELAY().
The old method slowed down a lot when the frequency became variable.
Assume the default frequency for short delays so that the fixed
point calculation can be exact.
Fast scaling is only important for small delays. Scaling is done
after looking at the counter and outside the loop, so it doesn't
decrease accuracy or resolution provided it completes before the
delay is up. The comment in the code is still confused about this.
- don't uselessly initialize the fifo "DMA" bit at attach time.
- initialize the fifo "DMA" bit at open time. Without this, the device
interrupts for every character received, reducing input performance
to that of an 8250.
- don't uselessly initialize the fifo trigger level to 8 (scaled to
256) at attach time.
- don't scale the fifo trigger level to 512 bytes. The driver's pseudo-
dma buffer has size 256, so it can't handle bursts of size 512 or 256.
It should be able to handle the second lowest ftl (2 scaled to 64).
- don't reset the fifos in siostop(). Reset triggers a hardware bug
involving wedging of the output interrupt bit This workaround
unfortunately requires ESP support to be configured.
an X seesion. Really stupid error of me, and I've been looking at
this code SO many times. Thanks to Kazutaka YOKOTA for seeing this..
Submitted by: Kazutaka YOKOTA
one in draw_mouse causes spontanious hangs on my p5-100 when I
move the mouse excessively. Forgot that on the last commit, so
using the mouse or destructive cursor would produce large amounts
of flicker..
cur_console is NULL when copy_font() is first called from scinit(). This
is apparently harmless when scinit() is called early from sccninit() -
page 0 is apparently mapped r/w then, and 0->status contains suitable
garbage. However, when there is a serial console, scinit() is first
called from scattach() when the page tables are completely initialized,
so the NULL pointer causes a panic.
Submitted by: bruce
called early for console i/o. The timer is usually in BIOS mode
if it isn't explicitly initialized. Then it counts twice as fast
and has a max count of 65535 instead of 11932. The larger count
tended to cause infinite loops for delays of > 20 us. Such delays
are rare. For syscons and kbdio, DELAY() is only called early
enough to matter for ddb input after booting with -d, and the delay
is too small to matter (and too small to be correct) except in the
PC98 case. For pcvt, DELAY() is not used for small delays (pcvt
uses its own broken routine instead of the standard broken one),
but some versions call DELAY() with a large arg when they unnecessarily
initialize the keyboard for doing console output. The problem is
more serious for pcvt because there is always some early console
output.
Guard against the i8254 timer being partially or incorrectly
initialized. This would have prevented the endless loop.
Should be in 2.2.
I have no idea if this works since I don't have one of the cards to test.
I also don't know what the LINT and GENERIC entries should look like,
so I just made up some values for now and left them commented out.
Someone who knows the factory settings for a Pro/10, please contact me!
Submitted-By: Javier Martín Rueda <jmrueda@diatel.upm.es>
