1
0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-24 11:29:10 +00:00
Commit Graph

63 Commits

Author SHA1 Message Date
Sam Leffler
5120abbfb4 Drop the driver lock around calls to if_input to avoid a LOR when
the packets are immediately returned for sending (e.g.  when bridging
or packet forwarding).  There are more efficient ways to do this
but for now use the least intrusive approach.

Reviewed by:	imp, rwatson
2003-11-14 19:00:32 +00:00
David E. O'Brien
4dc52c32bf Remove duplicate FBSDID's, move others to their right place. 2003-11-14 17:16:58 +00:00
David E. O'Brien
aa8255025a Try to create some sort of consistency in how the routings to find the
multicast hash are written.  There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
2003-11-13 20:55:53 +00:00
Brooks Davis
9bf40ede4a Replace the if_name and if_unit members of struct ifnet with new members
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.

This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.

Approved By:	re (in principle)
Reviewed By:	njl, imp
Tested On:	i386, amd64, sparc64
Obtained From:	NetBSD (if_xname)
2003-10-31 18:32:15 +00:00
Warner Losh
19b7ffd1b8 Prefer new location of pci include files (which have only been in the
tree for two or more years now), except in a few places where there's
code to be compatible with older versions of FreeBSD.
2003-08-22 07:20:27 +00:00
Warner Losh
b84e866a18 Due to extreme bogusness in the pci bus layer, these drivers were
forced to do slightly bogus power state manipulation.  However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...

This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
2003-07-03 21:39:53 +00:00
Poul-Henning Kamp
f22cfda31c Remove break after return
Found by:       FlexeLint
2003-05-31 19:59:29 +00:00
Warner Losh
214073e5e4 Use newly minted device_is_attached rather than device_is_alive to see
if attach succeeded.  device_is_alive just tells us that probe
succeeded.  Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.

Symptoms of problem reported by: martin blapp
2003-04-21 18:34:04 +00:00
Nate Lawson
693f4477b1 Revise attach/detach resource cleanup
- Unconditionally call *_stop() if device is in the tree. This is to
  prevent callouts from happening after the device is gone. Checks for
  bus_child_present() should be added in the future to keep from touching
  potentially non-existent hardware in *_detach().  Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
  the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
  that ifmedia_removeall() can be unconditionally called on detach. There
  is no way to detect whether ifmedia has been initialized without using
  a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
Matthew N. Dodd
533294b956 - Don't call pci_enable_io() in drivers (unless needed for resume).
- Don't test memory/port status and emit an error message; the PCI
  bus code will do this now.
2003-04-16 03:16:57 +00:00
Matthew N. Dodd
f246e4a17f - Express hard dependencies on bus (pci, isa, pccard) and
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
  such abuse isn't really needed.  (And if we do need type information
  associated with a module then we should make it explicit and not
  use hacks.)
2003-04-15 06:37:30 +00:00
David E. O'Brien
8368cf8f75 Use __FBSDID rather than rcsid[]. 2003-04-03 21:36:33 +00:00
John Baldwin
59f47d29b7 Add missing ()'s so that these drivers all compile again.
Noticed by:	jake
Tested on:	i386 (compile)
2003-03-31 20:22:00 +00:00
Nate Lawson
54f1f1d1e6 Clean up locking and resource management for pci/if_*
- Remove locking of the softc in the attach method, instead depending on
  bus_setup_intr being at the end of attach (delaying interrupt enable until
  after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
  in detach to only free resources that were allocated.  This puts all
  resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
  be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before.  It was unnecessary
  to move it.  This reverts part of 1.88
- rl: move irq allocation before ether_ifattach.  Problems might have been
  caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
  null pointer.

Reviewed by:	imp, mdodd
2003-03-31 17:29:43 +00:00
Warner Losh
a163d034fa Back out M_* changes, per decision of the TRB.
Approved by: trb
2003-02-19 05:47:46 +00:00
Alfred Perlstein
44956c9863 Remove M_TRYWAIT/M_WAITOK/M_WAIT. Callers should use 0.
Merge M_NOWAIT/M_DONTWAIT into a single flag M_NOWAIT.
2003-01-21 08:56:16 +00:00
Sam Leffler
9ef8b52020 o track either_ifattach/ether_ifdetach API changes
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes

Reviewed by:	many
Approved by:	re
2002-11-14 23:49:09 +00:00
Poul-Henning Kamp
88647b6de5 Be consistent about functions being static.
Properly put macro args in ().

Spotted by:	FlexeLint.
2002-10-16 09:14:59 +00:00
Bernd Walter
82026026e0 add missing \n to printf
Approved by:	gallatin (mentor)
2002-09-09 17:39:48 +00:00
Alfred Perlstein
e3d2833a26 style:
put return values on a line by themselves.
 fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
John Baldwin
6008862bc2 Change callers of mtx_init() to pass in an appropriate lock type name. In
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.

Tested on:	i386, alpha, sparc64
2002-04-04 21:03:38 +00:00
Alfred Perlstein
e51a25f850 Remove __P. 2002-03-20 02:08:01 +00:00
Luigi Rizzo
268cc03905 Remove printf's on mbuf/cluster allocation failures. There are now
equivalent and less dangerous (rate limited) messages in
the mbuf allocation code.

MFC after: 3 days
2001-12-14 05:56:35 +00:00
Jonathan Lemon
cd62a9cb38 Do not call mii_pollstat() from within device tick routines; the status
information is updated by mii_tick().

Pointed out by: wpaul (a while back)
2001-09-29 19:28:31 +00:00
Bill Paul
d3ab0d02cf After one more day of testing, make what I hope are the final tweaks to
prevent/workaround TX lockups in this driver. The secret seems to be to
not let the TX DMA queue become too full. If we have too many packets
in the queue, we should wait for them to drain a bit before trying to
queue more. This should prevent the lockup from occurring, and if it
does occur, there is special code in sf_start() to kick the NIC in the
head and get it going again.

Special thanks to Glen Neff for helping me test this fix.
2001-08-16 20:15:16 +00:00
Bill Paul
fa97ab323c Still more changes to try to prevent TX lockups. Will wait for one more
night of testing before merging to -stable.

Also added to code to detect TX underruns and automatically increase the
TX threshold to avoid them. Carefully placed diagnostig printf() about
this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from
confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
Bill Paul
0a4b345e9f Tweak the interrupt handler so that we call the txeof handler more often,
to hopefully prevent the TX DMA queue from filling up and never getting
flushed.
2001-08-15 17:46:57 +00:00
Bill Paul
75ff968cd5 Apply patch supplied by Jonathan Chen: use the correct arguments to
pci_enable_io(). We need to use SYS_RES_IOPORT/SYS_RES_MEMORY instead
of PCIM_CMD_PORTEN/PCIM_CMD_MEMEN.
2001-07-09 17:58:42 +00:00
Bosko Milekic
f5eece3fb9 Change m_devget()'s outdated and unused `offset' argument to actually mean
something: offset into the first mbuf of the target chain before copying
the source data over.

Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).

The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.

Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
2001-06-20 19:48:35 +00:00
Bill Paul
07f65363cd Big round of minor updates:
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
  that need them so we don't have to fiddle with the PCI power management
  registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
  PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
  a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
  mode in sis_reset(). This apparently fixes a problem on some
  motherboards where the DP83815 chip fails to receive packets.
  (Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
2001-02-21 20:54:22 +00:00
Poul-Henning Kamp
6817526d14 Convert if_multiaddrs from LIST to TAILQ so that it can be traversed
backwards in the three drivers which want to do that.

Reviewed by:    mikeh
2001-02-06 10:12:15 +00:00
Poul-Henning Kamp
37d4006626 Another round of the <sys/queue.h> FOREACH transmogriffer.
Created with:   sed(1)
Reviewed by:    md5(1)
2001-02-04 16:08:18 +00:00
Poul-Henning Kamp
fc2ffbe604 Mechanical change to use <sys/queue.h> macro API instead of
fondling implementation details.

Created with: sed(1)
Reviewed by: md5(1)
2001-02-04 13:13:25 +00:00
Poul-Henning Kamp
78d82c8c59 Use LIST_FOREACH() to traverse ifp->if_multiaddrs list, instead of
<sys/queue.h> implementation details.

Created with:   /usr/sbin/sed
Reviewed with:  /sbin/md5
2001-02-03 16:29:10 +00:00
Bill Paul
89689ecb7c Check the return value of sf_encap() and handle errors accordingly. 2001-01-20 00:50:51 +00:00
Bosko Milekic
08812b3925 Implement MTX_RECURSE flag for mtx_init().
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.

The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.

The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.

Reviewed by: jhb
2001-01-19 01:59:14 +00:00
Bill Paul
031fc810ab Initialize/grab the mutex earlier in the attach phase, so that
bailing out to the fail: label where we release/destroy the mutex
will work without exploding.
2000-12-04 22:46:50 +00:00
Poul-Henning Kamp
db7e3af111 Remove unneeded #include <machine/clock.h> 2000-10-15 14:19:01 +00:00
Bill Paul
1e856a7b34 Use device_get_nameunit(dev) as the mutex string when calling
mtx_init() instead of hard-coded string constant. Also remember to do
the mutex changes to the ste driver, which I forgot in the first commit.
2000-10-13 18:35:49 +00:00
Bill Paul
d1ce910572 First round of converting network drivers from spls to mutexes. This
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
2000-10-13 17:54:19 +00:00
Bill Paul
eddceb0d2b Close PR# 19904: remember to call sf_setmulti() when initializing the
interface so the multicast filter will be programmed correctly.
2000-07-14 19:11:02 +00:00
Archie Cobbs
21b8ebd926 Make all Ethernet drivers attach using ether_ifattach() and detach using
ether_ifdetach().

The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.

Reviewed by:	julian, freebsd-net
2000-07-13 22:54:34 +00:00
Peter Wemm
86b0a953e2 Use the correct register name. s/PCI_COMMAND_STATUS_REG/PCIR_COMMAND/ 2000-05-28 16:13:43 +00:00
Archie Cobbs
2e2de7f23f Move code to handle BPF and bridging for incoming Ethernet packets out
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.

The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.

The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.

Reviewed by:	freebsd-net
2000-05-14 02:18:43 +00:00
Peter Wemm
95a1645553 Depend on miibus.
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point.  if_aue does
strictly depend on miibus as it will fail to link if it is missing.
2000-04-29 13:41:57 +00:00
Bill Paul
d25bb2d026 Modify the Adaptec "starfire" driver to reset the PHY on the MII bus
before selecting a mode. The Seeq PHY chips on the Adaptec cards that
use the AIC-6915 controller seem to need it in order to get them to
change modes correctly.

This corrects a problem that I noticed where my ANA-62022 board failed
to correctly program the full duplex bit in the macconfig1 register
when the interface was brought up. Running ifconfig sf0 would mask this
problem in some cases because polling the PHY status would cause the
miibus code to notice that full duplex was now needed and the statchg
callback would be invoked to configure the duplex setting. However it
would still get it wrong other times.

Also changed sf_miibus_statchg() to program the IPG register to match
the duplex setting in accordance with Adaptec manual's recommendations
(0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
Bill Paul
5fb449fd94 Minor tweak: the subsystem device ID code for the quad port 62044 card
is documented to be 0x18 in the Adaptec manual, however there appears to
be a newer board rev with code 0x19. I added a #define for this and
updated the probe code so that this board will be properly identified
in the probe messages. (Currently it's just identified generically as
an AIC-6915 chip.)
1999-11-20 18:29:44 +00:00
Bill Paul
c63d3a6678 Update the Starfire driver comments and man page to include the URL of
the AIC-6915 Programmer's Manual which I finally found online at Adaptec's
site.
1999-09-26 18:35:30 +00:00
Bill Paul
784733e9ec Change contigmalloc() lower memory bound from 1MB to 0 to improve
chances of allocations succeeding on systems with small amounts of
RAM.

Pointed out by: bde
1999-09-25 17:29:02 +00:00
Bill Paul
98a229f65e As suggested by phk, unconditionalize BPF support in these drivers. Since
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
1999-09-23 03:32:57 +00:00