former more explicitly tells the compiler that you want an empty loop.
There are some lint programs that use this hint to avoid generating
warnings.
No functional change...
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
When I changed kern_conf.c three months ago I made device unit numbers
equal to (unneeded) device minor numbers. We used to require
bitshifting, because there were eight bits in the middle that were
reserved for a device major number. Not very long after I turned
dev2unit(), minor(), unit2minor() and minor2unit() into macro's.
The unit2minor() and minor2unit() macro's were no-ops.
We'd better not remove these four macro's from the kernel, because there
is a lot of (external) code that may still depend on them. For now it's
harmless to remove all invocations of unit2minor() and minor2unit().
Reviewed by: kib
Thanks goes to ITE who provided docs and feedback and made this possible.
Minor fixups to the Intel ICH code for bugs found while doing this.
(ITE8213 is very semilar to an Intel ICH)
MFC after: 1 week
Kick the device into the right mode if it comes up as a flash-disk.
Set the buffers to a sensible 1024 bytes instead of a far too small
default.
Don't attempt to change speed, baud, parity and such, the device does
not understand it.
have hardware ram buffer. The silicon bug seem to be triggered by
pause frames if receive buffer is not aligned on FIFO word(8 bytes).
To workaround the issue, make sure to align Rx buffers on 8 bytes.
Unfortunately this workaround requires yet another Rx fixup for
strict alignment architecture machines to align IP header.
For newer hardwares that lacks ram buffer may not have this bug so
check number of available ram buffer size to see the existence of
ram buffer.
Reported by: Ian Freislich (ianf <at> clue dot co dot za), das
Tested by: Ian Freislich (ianf <at> clue dot co dot za)
containing an Ethernet address fitted as this is yet another thing
that fails in that case in order to avoid the one second delay
until pci_read_vpd_reg() times out.
- Const'ify the bge_devs array.
when it runs on half-duplex media.
While I'm here add register definition for GPREG1. ATM the GPREG1
register is only valid for JMC250 A1/A2.
Submitted by: Ethan at JMicron
o don't use the key index to identify when the driver has been
asked to allocate a key slot, use an explicit flag; allows
drivers to force s/w fallback for entries in the global table
o change callback api to allocate driver resources for a crypto key:
- de-const the key parameter so drivers can muck with the flags
- on callback failure don't automatically try to setup s/w crypto;
instead the driver must now mark the key entry for s/w crypto and
the caller will re-attach the cipher module
NB: api change permits drivers more control over fallback to s/w
crypto (e.g. based on a limited number of h/w key slots)
to vga_pci.c to request on behalf of it's children. This causes vgapci to show
up as the interrupt owner in vmstat -i, rather than the child device.
Approved by: jhb(mentor)
kib@ and I have decided we will MFC the bpf(4)/snp(4) fixes after we've
released 7.1. Make sure the code in HEAD doesn't refer to a flag we
don't need anyway.
snp(4) in the MPSAFE TTY P4 branch already works, but still needs some
polishing before it can be integrated to SVN.
this also can be happened if we pull the USN stick out forcibly.
Currently the ZyDAS driver uses tsleep() when it try to query a read
command to the device and it'd make a timeout if the device doesn't
response within about 1 sec.
In a case of that the USB stick is gone by hand and the driver's
scanning with changing the channel numbers, the thread which is sleeping
until a command requested is responded can be waked up after all
detaching routines finished that means the zyd softc already freed.
Tring to touch the softc freed by the wakeup thread makes a panic.
So make sure that all sleeping threads should be waken up before the
detach is completed and any other new requests to the device should be
prevented.
years by the priv_check(9) interface and just very few places are left.
Note that compatibility stub with older FreeBSD version
(all above the 8 limit though) are left in order to reduce diffs against
old versions. It is responsibility of the maintainers for any module, if
they think it is the case, to axe out such cases.
This patch breaks KPI so __FreeBSD_version will be bumped into a later
commit.
This patch needs to be credited 50-50 with rwatson@ as he found time to
explain me how the priv_check() works in detail and to review patches.
Tested by: Giovanni Trematerra <giovanni dot trematerra at gmail dot com>
Reviewed by: rwatson
Left only parts surely required for basic troubleshooting and configuration
purposes. There is still very long output, but further shrinking makes it
less informative.
Original debugging can be enabled with hw.snd.verbose=4.
